at91: Status of NAND flash access
Bryan Evenson
bevenson at melinkcorp.com
Tue Dec 4 11:24:39 EST 2012
> -----Original Message-----
> From: Josh Wu [mailto:josh.wu at atmel.com]
> Sent: Tuesday, December 04, 2012 5:54 AM
> To: Bryan Evenson
> Cc: linux-arm-kernel at lists.infradead.org
> Subject: Re: at91: Status of NAND flash access
>
> Hi, Bryan
>
> On 12/3/2012 10:39 PM, Bryan Evenson wrote:
> > I have a kernel build of 3.7-rc5 that is built for the AT91SAM9G25.
> The kernel has issues when it tries to read the filesystem from NAND
> flash. If I change to an NFS setup then the filesystem loads.
> According to your question, it is not very clear to me, so could you
> give more detail then I can help.
>
> What type (ubi, jffs2, or others) of your filesystem is used? How do
> you flush the file system into the nand flash, by SAM-BA, or U-Boot?
> With or without pmecc?
> And what ecc type (pmecc, soft, none) do you enabled in the kernel?
>
I have a UBI filesystem, built using OE (2011.03-maintenance branch).
I've been burning the filesystem to flash using SAM-BA, following the
instructions on the Atmel Linux4SAM site (on this page here: http://www.at91.com/linux4sam/bin/view/Linux4SAM/FlashRootFs_9x5).
Here are all my MTD and filesystem related flags I have enabled in my
kernel configuration. If you see any missing that I should have set
for UBI access of NAND flash, please let me know.
Also note that I am using the instructions found here to build this
kernel: http://www.eewiki.net/display/linuxonarm/AT91SAM9x5, which
means I am using the kernel extracted from the listed fork with the
listed patches applied.
#
# Bus devices
#
CONFIG_MTD=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_OF_PARTS=y
#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLKDEVS=y
CONFIG_MTD_BLOCK=y
#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
#
# Disk-On-Chip Device Drivers
#
CONFIG_MTD_NAND_ECC=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_IDS=y
CONFIG_MTD_NAND_ATMEL=y
#
# LPDDR flash memory drivers
#
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_LIMIT=20
CONFIG_MTD_UBI_GLUEBI=y
CONFIG_DTC=y
CONFIG_OF=y
#
# Device Tree and Open Firmware support
#
CONFIG_PROC_DEVICETREE=y
CONFIG_OF_FLATTREE=y
CONFIG_OF_EARLY_FLATTREE=y
CONFIG_OF_ADDRESS=y
CONFIG_OF_IRQ=y
CONFIG_OF_DEVICE=y
CONFIG_OF_I2C=y
CONFIG_OF_NET=y
CONFIG_OF_MDIO=y
CONFIG_OF_MTD=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_LOOP_MIN_COUNT=8
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_DEFAULTS_TO_ORDERED=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_EXT4_FS=y
CONFIG_EXT4_FS_XATTR=y
CONFIG_EXT4_FS_POSIX_ACL=y
CONFIG_EXT4_FS_SECURITY=y
CONFIG_JBD=y
CONFIG_JBD2=y
CONFIG_FS_MBCACHE=y
CONFIG_FS_POSIX_ACL=y
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY_USER=y
CONFIG_FANOTIFY=y
CONFIG_GENERIC_ACL=y
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
CONFIG_TMPFS_XATTR=y
CONFIG_MISC_FILESYSTEMS=y
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_FS_DEBUG=0
CONFIG_JFFS2_FS_WRITEBUFFER=y
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_RTIME=y
CONFIG_UBIFS_FS=y
CONFIG_UBIFS_FS_ADVANCED_COMPR=y
CONFIG_UBIFS_FS_LZO=y
CONFIG_UBIFS_FS_ZLIB=y
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V2=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
CONFIG_NFS_USE_KERNEL_DNS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_ACL_SUPPORT=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_850=y
CONFIG_NLS_ISO8859_1=y
> > I've seen some patches on this list lately related to AT91 NAND flash
> (specifically this thread: http://lists.infradead.org/pipermail/linux-
> arm-kernel/2012-November/133748.html) and I believe my problems may be
> related to this issue. But, I'm having trouble following the thread to
> find the current status.
> >
> > Can anyone tell me what the status is on NAND flash access for the
> AT91 series with the 3.7-rc5 kernel? If this version has a known bug,
> is there a different suggested version I use that fixes the issue?
> In 3.7-rc5, I think the atmel nand driver should work well with
> AT91SAM9G25EK board even without the patch you mentioned in above URL.
>
> Just for PMECC, you need add following code in
> arch/arm/boot/dts/at91sam9x5cm.dtsi:
> - nand-ecc-mode = "soft";
> + nand-ecc-mode = "hw";
> + atmel,has-pmecc; /* Enable PMECC */
> + atmel,pmecc-cap = <2>; /* PMECC error
> bits*/
> + atmel,pmecc-sector-size = <512>; /* sector
> size for PMECC, it is not page size */
>
> Also you can check the readme file in:
> Documentation/devicetree/bindings/mtd/atmel-nand.txt
>
I did not have the NAND flash setup correctly in the dtsi. I applied the patch
that you provided, rebuilt and reloaded my kernel. Unfortunately, the filesystem
is still not being read from flash correctly. It looks like the kernel
correctly identifies the NAND flash and sets up the partitions, but has problems
when it attempts to read out the filesystem. Here is the kernel boot output.
Do you see anything that tells you what may be going wrong?
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.7.0-rc7-armv5-x0.11 (xxxx at xxxx) (gcc versio
n 4.6.2 20121016 (release) [ARM/embedded-4_6-branch revision 192487] (GNU Tools
for ARM Embedded Processors) ) #1 Tue Dec 4 10:29:17 EST 2012
[ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Atmel AT91SAM (Device Tree), model: Atmel AT91SAM9G25-EK
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] AT91: Detected soc type: at91sam9x5
[ 0.000000] AT91: Detected soc subtype: at91sam9g25
[ 0.000000] AT91: sram at 0x300000 of 0x8000 mapped at 0xfef70000
[ 0.000000] Clocks: CPU 400 MHz, master 133 MHz, main 12.000 MHz
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 32512
[ 0.000000] Kernel command line: mem=128M console=ttyS0,115200 mtdparts=atmel
_nand:8M(bootstrap/uboot/kernel)ro,-(rootfs) root=/dev/mtdblock1 rw rootfstype=u
bifs ubi.mtd=1 root=ubi0:rootfs
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 124312k/124312k available, 6760k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc04b01d8 (4769 kB)
[ 0.000000] .init : 0xc04b1000 - 0xc04dc304 ( 173 kB)
[ 0.000000] .data : 0xc04de000 - 0xc050e9a0 ( 195 kB)
[ 0.000000] .bss : 0xc050e9c4 - 0xc056dd1c ( 381 kB)
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] sched_clock: 32 bits at 256 Hz, resolution 3906250ns, wraps every
3892314108ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.035156] Calibrating delay loop... 199.80 BogoMIPS (lpj=389120)
[ 0.035156] pid_max: default: 32768 minimum: 301
[ 0.035156] Mount-cache hash table entries: 512
[ 0.039062] CPU: Testing write buffer coherency: ok
[ 0.039062] Setting up static identity map for 0x2036cb00 - 0x2036cb58
[ 0.039062] devtmpfs: initialized
[ 0.042968] NET: Registered protocol family 16
[ 0.042968] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.070312] No ATAGs?
[ 0.070312] AT91: Power Management
[ 0.070312] AT91: Starting after power-restored wakeup
[ 0.125000] bio: create slab <bio-0> at 0
[ 0.128906] SCSI subsystem initialized
[ 0.132812] usbcore: registered new interface driver usbfs
[ 0.132812] usbcore: registered new interface driver hub
[ 0.132812] usbcore: registered new device driver usb
[ 0.136718] at91_i2c f8010000.i2c: AT91 i2c bus driver.
[ 0.136718] at91_i2c f8014000.i2c: AT91 i2c bus driver.
[ 0.140625] at91_i2c f8018000.i2c: AT91 i2c bus driver.
[ 0.144531] Switching to clocksource tcb_clksrc
[ 0.199218] NET: Registered protocol family 2
[ 0.203125] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.203125] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.203125] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.203125] TCP: reno registered
[ 0.203125] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.203125] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.203125] NET: Registered protocol family 1
[ 0.203125] RPC: Registered named UNIX socket transport module.
[ 0.203125] RPC: Registered udp transport module.
[ 0.203125] RPC: Registered tcp transport module.
[ 0.203125] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.210937] NFS: Registering the id_resolver key type
[ 0.210937] Key type id_resolver registered
[ 0.210937] Key type id_legacy registered
[ 0.210937] jffs2: version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
[ 0.210937] msgmni has been set to 242
[ 0.210937] io scheduler noop registered (default)
[ 0.222656] fffff200.serial: ttyS0 at MMIO 0xfffff200 (irq = 18) is a ATMEL_S
ERIAL
[ 0.613281] console [ttyS0] enabled
[ 0.617187] f801c000.serial: ttyS1 at MMIO 0xf801c000 (irq = 22) is a ATMEL_S
ERIAL
[ 0.632812] brd: module loaded
[ 0.652343] loop: module loaded
[ 0.667968] atmel_nand: Use On Flash BBT
[ 0.671875] atmel_nand 40000000.nand: No DMA support for NAND access.
[ 0.679687] ONFI param page 0 valid
[ 0.683593] ONFI flash detected
[ 0.687500] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G
08AAD), page size: 2048, OOB size: 64
[ 0.699218] Bad block table found at page 131008, version 0x01
[ 0.703125] Bad block table found at page 130944, version 0x01
[ 0.710937] nand_read_bbt: bad block at 0x000009380000
[ 0.714843] 2 cmdlinepart partitions found on MTD device atmel_nand
[ 0.722656] Creating 2 MTD partitions on "atmel_nand":
[ 0.726562] 0x000000000000-0x000000800000 : "bootstrap/uboot/kernel"
[ 0.734375] 0x000000800000-0x000010000000 : "rootfs"
[ 0.753906] macb f802c000.ethernet (unregistered net_device): invalid hw addr
ess, using random
[ 0.765625] libphy: MACB_mii_bus: probed
[ 0.769531] macb f802c000.ethernet eth0: Cadence MACB at 0xf802c000 irq 23 (4
a:b7:82:09:12:d7)
[ 0.781250] macb f802c000.ethernet eth0: attached PHY driver [Davicom DM9161A
] (mii_bus:phy_addr=f802c000.etherne:00, irq=-1)
[ 0.792968] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.800781] atmel-ehci 700000.ehci: Atmel EHCI UHP HS
[ 0.804687] atmel-ehci 700000.ehci: new USB bus registered, assigned bus numb
er 1
[ 0.812500] atmel-ehci 700000.ehci: irq 30, io mem 0x00700000
[ 0.828125] atmel-ehci 700000.ehci: USB 2.0 started, EHCI 1.00
[ 0.832031] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.839843] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 0.847656] usb usb1: Product: Atmel EHCI UHP HS
[ 0.851562] usb usb1: Manufacturer: Linux 3.7.0-rc7-armv5-x0.11 ehci_hcd
[ 0.859375] usb usb1: SerialNumber: 700000.ehci
[ 0.863281] hub 1-0:1.0: USB hub found
[ 0.867187] hub 1-0:1.0: 3 ports detected
[ 0.875000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.878906] at91_ohci 600000.ohci: AT91 OHCI
[ 0.882812] at91_ohci 600000.ohci: new USB bus registered, assigned bus numbe
r 2
[ 0.890625] at91_ohci 600000.ohci: irq 30, io mem 0x00600000
[ 0.957031] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.960937] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 0.968750] usb usb2: Product: AT91 OHCI
[ 0.972656] usb usb2: Manufacturer: Linux 3.7.0-rc7-armv5-x0.11 ohci_hcd
[ 0.980468] usb usb2: SerialNumber: at91
[ 0.984375] hub 2-0:1.0: USB hub found
[ 0.988281] hub 2-0:1.0: 2 ports detected
[ 0.996093] usbcore: registered new interface driver cdc_acm
[ 1.000000] cdc_acm: USB Abstract Control Model driver for USB modems and ISD
N adapters
[ 1.011718] usbcore: registered new interface driver uas
[ 1.015625] Initializing USB Mass Storage driver...
[ 1.019531] usbcore: registered new interface driver usb-storage
[ 1.027343] USB Mass Storage support registered.
[ 1.031250] usbcore: registered new interface driver ums-alauda
[ 1.039062] usbcore: registered new interface driver ums-cypress
[ 1.046875] usbcore: registered new interface driver ums-datafab
[ 1.050781] usbcore: registered new interface driver ums_eneub6250
[ 1.058593] usbcore: registered new interface driver ums-freecom
[ 1.066406] usbcore: registered new interface driver ums-isd200
[ 1.070312] usbcore: registered new interface driver ums-jumpshot
[ 1.078125] usbcore: registered new interface driver ums-karma
[ 1.085937] usbcore: registered new interface driver ums-onetouch
[ 1.089843] usbcore: registered new interface driver ums-realtek
[ 1.097656] usbcore: registered new interface driver ums-sddr09
[ 1.105468] usbcore: registered new interface driver ums-sddr55
[ 1.109375] usbcore: registered new interface driver ums-usbat
[ 1.117187] usbcore: registered new interface driver usbserial
[ 1.125000] usbcore: registered new interface driver usbserial_generic
[ 1.132812] usbserial: USB Serial support registered for generic
[ 1.136718] usbcore: registered new interface driver ftdi_sio
[ 1.144531] usbserial: USB Serial support registered for FTDI USB Serial Devi
ce
[ 1.152343] usbcore: registered new interface driver pl2303
[ 1.156250] usbserial: USB Serial support registered for pl2303
[ 1.164062] mousedev: PS/2 mouse device common for all mice
[ 1.171875] i2c /dev entries driver
[ 1.183593] usbcore: registered new interface driver usbhid
[ 1.191406] usbhid: USB HID core driver
[ 1.195312] TCP: cubic registered
[ 1.195312] NET: Registered protocol family 10
[ 1.203125] sit: IPv6 over IPv4 tunneling driver
[ 1.210937] NET: Registered protocol family 17
[ 1.214843] Key type dns_resolver registered
[ 1.226562] UBI: attaching mtd1 to ubi0
[ 1.230468] uncorrectable error :
[ 1.234375] UBI warning: ubi_io_read: error -74 (ECC error) while reading 64
bytes from PEB 0:0, read only 64 bytes, retry
[ 1.242187] uncorrectable error :
[ 1.246093] UBI warning: ubi_io_read: error -74 (ECC error) while reading 64
bytes from PEB 0:0, read only 64 bytes, retry
[ 1.257812] uncorrectable error :
[ 1.261718] UBI warning: ubi_io_read: error -74 (ECC error) while reading 64
bytes from PEB 0:0, read only 64 bytes, retry
[ 1.273437] uncorrectable error :
[ 1.277343] UBI error: ubi_io_read: error -74 (ECC error) while reading 64 by
tes from PEB 0:0, read 64 bytes
[ 1.285156] [<c000d2bc>] (unwind_backtrace+0x0/0xe0) from [<c0243764>] (ubi_i
o_read+0x1d4/0x2a4)
[ 1.292968] [<c0243764>] (ubi_io_read+0x1d4/0x2a4) from [<c0243a74>] (ubi_io_
read_ec_hdr+0x68/0x214)
[ 1.304687] [<c0243a74>] (ubi_io_read_ec_hdr+0x68/0x214) from [<c0247da0>] (u
bi_attach+0x104/0x13e4)
[ 1.312500] [<c0247da0>] (ubi_attach+0x104/0x13e4) from [<c023e268>] (ubi_att
ach_mtd_dev+0x5a4/0xb94)
[ 1.320312] [<c023e268>] (ubi_attach_mtd_dev+0x5a4/0xb94) from [<c04c88d4>] (
ubi_init+0x1d8/0x2d8)
[ 1.332031] [<c04c88d4>] (ubi_init+0x1d8/0x2d8) from [<c0008860>] (do_one_ini
tcall+0x90/0x168)
[ 1.339843] [<c0008860>] (do_one_initcall+0x90/0x168) from [<c0363f10>] (kern
el_init+0xe4/0x298)
[ 1.347656] [<c0363f10>] (kernel_init+0xe4/0x298) from [<c00093f0>] (ret_from
_fork+0x14/0x24)
[ 1.355468] UBI error: validate_ec_hdr: bad VID header offset 2048, expected
512
[ 1.363281] UBI error: validate_ec_hdr: bad EC header
[ 1.367187] Erase counter header dump:
[ 1.371093] magic 0x55424923
[ 1.375000] version 1
[ 1.378906] ec 4
[ 1.382812] vid_hdr_offset 2048
[ 1.386718] data_offset 4096
[ 1.390625] image_seq 191777507
[ 1.390625] hdr_crc 0xecd7a545
[ 1.394531] erase counter header hexdump:
[ 1.398437] [<c000d2bc>] (unwind_backtrace+0x0/0xe0) from [<c024303c>] (valid
ate_ec_hdr+0x148/0x168)
[ 1.410156] [<c024303c>] (validate_ec_hdr+0x148/0x168) from [<c0243bc4>] (ubi
_io_read_ec_hdr+0x1b8/0x214)
[ 1.417968] [<c0243bc4>] (ubi_io_read_ec_hdr+0x1b8/0x214) from [<c0247da0>] (
ubi_attach+0x104/0x13e4)
[ 1.429687] [<c0247da0>] (ubi_attach+0x104/0x13e4) from [<c023e268>] (ubi_att
ach_mtd_dev+0x5a4/0xb94)
[ 1.437500] [<c023e268>] (ubi_attach_mtd_dev+0x5a4/0xb94) from [<c04c88d4>] (
ubi_init+0x1d8/0x2d8)
[ 1.445312] [<c04c88d4>] (ubi_init+0x1d8/0x2d8) from [<c0008860>] (do_one_ini
tcall+0x90/0x168)
[ 1.453125] [<c0008860>] (do_one_initcall+0x90/0x168) from [<c0363f10>] (kern
el_init+0xe4/0x298)
[ 1.464843] [<c0363f10>] (kernel_init+0xe4/0x298) from [<c00093f0>] (ret_from
_fork+0x14/0x24)
[ 1.472656] UBI error: ubi_io_read_ec_hdr: validation failed for PEB 0
[ 1.476562] UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -22
[ 1.484375] UBI error: ubi_init: cannot attach mtd1
[ 1.492187] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.496093] atmel_mci f0008000.mmc: version: 0x504
[ 1.503906] atmel_mci f0008000.mmc: using PIO
[ 1.539062] atmel_mci f0008000.mmc: Atmel MCI controller at 0xf0008000 irq 28
, 1 slots
[ 1.546875] atmel_mci f000c000.mmc: version: 0x504
[ 1.550781] atmel_mci f000c000.mmc: using PIO
[ 1.585937] atmel_mci f000c000.mmc: Atmel MCI controller at 0xf000c000 irq 29
, 1 slots
[ 1.593750] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", erro
r -19
[ 1.601562] VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0):
error -19
[ 1.609375] Please append a correct "root=" boot option; here are the availab
le partitions:
[ 1.617187] 1f00 8192 mtdblock0 (driver?)
[ 1.621093] 1f01 253952 mtdblock1 (driver?)
[ 1.628906] Kernel panic - not syncing: VFS: Unable to mount root fs on unkno
wn-block(0,0)
Thanks,
Bryan
> Best Regards,
> Josh Wu
>
> >
> > Thanks,
> > Bryan
> >
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel at lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
More information about the linux-arm-kernel
mailing list