[PATCH 33/33] ARM: i.MX6: implement clocks using common clock framework

[Sascha Hauer]

On Thu, Apr 26, 2012 at 10:48:38AM +0800, Richard Zhao wrote:
> The below code is removed from mx6q_clocks_init implicitly.
> Why? If it's reasonable, it needs to be on a separate patch too.
> 
> /* only keep necessary clocks on */
> writel_relaxed(0x3 << CG0  | 0x3 << CG1  | 0x3 << CG2,  CCGR0);
> writel_relaxed(0x3 << CG8  | 0x3 << CG9  | 0x3 << CG10, CCGR2);
> writel_relaxed(0x3 << CG10 | 0x3 << CG12,               CCGR3);
> writel_relaxed(0x3 << CG4  | 0x3 << CG6  | 0x3 << CG7,  CCGR4);
> writel_relaxed(0x3 << CG0,                              CCGR5);
> writel_relaxed(0,                                       CCGR6);
> writel_relaxed(0,                                       CCGR7);

The clock framework will turn them off automatically.
For the first time the hardware state will be consistent with the
software state. Hurray!

> 
> clk_enable(&uart_clk);

This is not needed anymore. For the early debug case we depend on the
uart being enabled by the bootloader anyway, so it's safe to assume that
the clock is turned on also. Otherwise the uart driver turns on this
clock when needed.

> clk_enable(&mmdc_ch0_axi_clk);

This reminds me on something. This clock is turned on in the loop around
clks_init_on. Since we now have pointers to each clock we don't need the
clk_get_sys() anymore but can use the pointers directly. Will fix this
one.

> 
> clk_set_rate(&pll4_audio, FREQ_650M);
> clk_set_rate(&pll5_video, FREQ_650M);
> clk_set_parent(&ipu1_di0_clk, &ipu1_di0_pre_clk);
> clk_set_parent(&ipu1_di0_pre_clk, &pll5_video);
> clk_set_parent(&gpu3d_shader_clk, &pll2_pfd_594m);
> clk_set_rate(&gpu3d_shader_clk, FREQ_594M);
> clk_set_parent(&gpu3d_core_clk, &mmdc_ch0_axi_clk);
> clk_set_rate(&gpu3d_core_clk, FREQ_528M);
> clk_set_parent(&asrc_serial_clk, &pll3_usb_otg);
> clk_set_rate(&asrc_serial_clk, 1500000);
> clk_set_rate(&enfc_clk, 11000000);
> 
> /*
>  * Before pinctrl API is available, we have to rely on the pad
>  * configuration set up by bootloader.  For usdhc example here,
>  * u-boot sets up the pads for 49.5 MHz case, and we have to lower
>  * the usdhc clock from 198 to 49.5 MHz to match the pad configuration.
>  *
>  * FIXME: This is should be removed after pinctrl API is available.
>  * At that time, usdhc driver can call pinctrl API to change pad
>  * configuration dynamically per different usdhc clock settings.
>  */
> clk_set_rate(&usdhc1_clk, 49500000);
> clk_set_rate(&usdhc2_clk, 49500000);
> clk_set_rate(&usdhc3_clk, 49500000);
> clk_set_rate(&usdhc4_clk, 49500000);

Can't say anything to these, probably Shawn has simply lost them while
porting.

> 
> clk_set_parent(&cko1_clk, &ahb_clk);

Why this? The cko pin has different usecases on each board, mostly I
think for debugging. We shouldn't touch it here.

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |