[PATCH v5 9/10] ARM: LPC32xx: Device tree support
Roland Stigge
stigge at antcom.de
Sat Apr 21 05:34:27 EDT 2012
This patch does the actual device tree switch for the LPC32xx SoC.
Signed-off-by: Roland Stigge <stigge at antcom.de>
---
Applies to v3.4-rc3
Documentation/devicetree/bindings/arm/lpc32xx-mic.txt | 38 +++
Documentation/devicetree/bindings/arm/lpc32xx.txt | 8
arch/arm/Kconfig | 1
arch/arm/mach-lpc32xx/common.c | 192 ------------------
arch/arm/mach-lpc32xx/common.h | 14 -
arch/arm/mach-lpc32xx/irq.c | 78 +++++--
arch/arm/mach-lpc32xx/phy3250.c | 138 ++++--------
7 files changed, 158 insertions(+), 311 deletions(-)
--- /dev/null
+++ linux-2.6/Documentation/devicetree/bindings/arm/lpc32xx-mic.txt
@@ -0,0 +1,38 @@
+* NXP LPC32xx Main Interrupt Controller
+ (MIC, including SIC1 and SIC2 secondary controllers)
+
+Required properties:
+- compatible: Should be "nxp,lpc3220-mic"
+- interrupt-controller: Identifies the node as an interrupt controller.
+- interrupt-parent: Empty for the interrupt controller itself
+- #interrupt-cells: The number of cells to define the interrupts. Should be 2.
+ The first cell is the IRQ number
+ The second cell is used to specify mode:
+ 1 = low-to-high edge triggered
+ 2 = high-to-low edge triggered
+ 4 = active high level-sensitive
+ 8 = active low level-sensitive
+ Default for internal sources should be set to 4 (active high).
+- reg: Should contain MIC registers location and length
+
+Examples:
+ /*
+ * MIC
+ */
+ mic: interrupt-controller at 40008000 {
+ compatible = "nxp,lpc3220-mic";
+ interrupt-controller;
+ interrupt-parent;
+ #interrupt-cells = <2>;
+ reg = <0x40008000 0xC000>;
+ };
+
+ /*
+ * ADC
+ */
+ adc at 40048000 {
+ compatible = "nxp,lpc3220-adc";
+ reg = <0x40048000 0x1000>;
+ interrupt-parent = <&mic>;
+ interrupts = <39 4>;
+ };
--- /dev/null
+++ linux-2.6/Documentation/devicetree/bindings/arm/lpc32xx.txt
@@ -0,0 +1,8 @@
+NXP LPC32xx Platforms Device Tree Bindings
+------------------------------------------
+
+Boards with the NXP LPC32xx SoC shall have the following properties:
+
+Required root node property:
+
+compatible: must be "nxp,lpc3220", "nxp,lpc3230", "nxp,lpc3240" or "nxp,lpc3250"
--- linux-2.6.orig/arch/arm/Kconfig
+++ linux-2.6/arch/arm/Kconfig
@@ -597,6 +597,7 @@ config ARCH_LPC32XX
select USB_ARCH_HAS_OHCI
select CLKDEV_LOOKUP
select GENERIC_CLOCKEVENTS
+ select USE_OF
help
Support for the NXP LPC32XX family of processors
--- linux-2.6.orig/arch/arm/mach-lpc32xx/common.c
+++ linux-2.6/arch/arm/mach-lpc32xx/common.c
@@ -32,198 +32,6 @@
#include "common.h"
/*
- * Watchdog timer
- */
-static struct resource watchdog_resources[] = {
- [0] = {
- .start = LPC32XX_WDTIM_BASE,
- .end = LPC32XX_WDTIM_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-struct platform_device lpc32xx_watchdog_device = {
- .name = "pnx4008-watchdog",
- .id = -1,
- .num_resources = ARRAY_SIZE(watchdog_resources),
- .resource = watchdog_resources,
-};
-
-/*
- * I2C busses
- */
-static struct resource i2c0_resources[] = {
- [0] = {
- .start = LPC32XX_I2C1_BASE,
- .end = LPC32XX_I2C1_BASE + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_LPC32XX_I2C_1,
- .end = IRQ_LPC32XX_I2C_1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c1_resources[] = {
- [0] = {
- .start = LPC32XX_I2C2_BASE,
- .end = LPC32XX_I2C2_BASE + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_LPC32XX_I2C_2,
- .end = IRQ_LPC32XX_I2C_2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c2_resources[] = {
- [0] = {
- .start = LPC32XX_OTG_I2C_BASE,
- .end = LPC32XX_OTG_I2C_BASE + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_LPC32XX_USB_I2C,
- .end = IRQ_LPC32XX_USB_I2C,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device lpc32xx_i2c0_device = {
- .name = "pnx-i2c.0",
- .id = 0,
- .num_resources = ARRAY_SIZE(i2c0_resources),
- .resource = i2c0_resources,
-};
-
-struct platform_device lpc32xx_i2c1_device = {
- .name = "pnx-i2c.1",
- .id = 1,
- .num_resources = ARRAY_SIZE(i2c1_resources),
- .resource = i2c1_resources,
-};
-
-struct platform_device lpc32xx_i2c2_device = {
- .name = "pnx-i2c.2",
- .id = 2,
- .num_resources = ARRAY_SIZE(i2c2_resources),
- .resource = i2c2_resources,
-};
-
-/* TSC (Touch Screen Controller) */
-
-static struct resource lpc32xx_tsc_resources[] = {
- {
- .start = LPC32XX_ADC_BASE,
- .end = LPC32XX_ADC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_LPC32XX_TS_IRQ,
- .end = IRQ_LPC32XX_TS_IRQ,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device lpc32xx_tsc_device = {
- .name = "ts-lpc32xx",
- .id = -1,
- .num_resources = ARRAY_SIZE(lpc32xx_tsc_resources),
- .resource = lpc32xx_tsc_resources,
-};
-
-/* RTC */
-
-static struct resource lpc32xx_rtc_resources[] = {
- {
- .start = LPC32XX_RTC_BASE,
- .end = LPC32XX_RTC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },{
- .start = IRQ_LPC32XX_RTC,
- .end = IRQ_LPC32XX_RTC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device lpc32xx_rtc_device = {
- .name = "rtc-lpc32xx",
- .id = -1,
- .num_resources = ARRAY_SIZE(lpc32xx_rtc_resources),
- .resource = lpc32xx_rtc_resources,
-};
-
-/*
- * ADC support
- */
-static struct resource adc_resources[] = {
- {
- .start = LPC32XX_ADC_BASE,
- .end = LPC32XX_ADC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_LPC32XX_TS_IRQ,
- .end = IRQ_LPC32XX_TS_IRQ,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device lpc32xx_adc_device = {
- .name = "lpc32xx-adc",
- .id = -1,
- .num_resources = ARRAY_SIZE(adc_resources),
- .resource = adc_resources,
-};
-
-/*
- * USB support
- */
-/* The dmamask must be set for OHCI to work */
-static u64 ohci_dmamask = ~(u32) 0;
-static struct resource ohci_resources[] = {
- {
- .start = IO_ADDRESS(LPC32XX_USB_BASE),
- .end = IO_ADDRESS(LPC32XX_USB_BASE + 0x100 - 1),
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_LPC32XX_USB_HOST,
- .flags = IORESOURCE_IRQ,
- },
-};
-struct platform_device lpc32xx_ohci_device = {
- .name = "usb-ohci",
- .id = -1,
- .dev = {
- .dma_mask = &ohci_dmamask,
- .coherent_dma_mask = 0xFFFFFFFF,
- },
- .num_resources = ARRAY_SIZE(ohci_resources),
- .resource = ohci_resources,
-};
-
-/*
- * Network Support
- */
-static struct resource net_resources[] = {
- [0] = DEFINE_RES_MEM(LPC32XX_ETHERNET_BASE, SZ_4K),
- [1] = DEFINE_RES_MEM(LPC32XX_IRAM_BASE, SZ_128K),
- [2] = DEFINE_RES_IRQ(IRQ_LPC32XX_ETHERNET),
-};
-
-static u64 lpc32xx_mac_dma_mask = 0xffffffffUL;
-struct platform_device lpc32xx_net_device = {
- .name = "lpc-eth",
- .id = 0,
- .dev = {
- .dma_mask = &lpc32xx_mac_dma_mask,
- .coherent_dma_mask = 0xffffffffUL,
- },
- .num_resources = ARRAY_SIZE(net_resources),
- .resource = net_resources,
-};
-
-/*
* Returns the unique ID for the device
*/
void lpc32xx_get_uid(u32 devid[4])
--- linux-2.6.orig/arch/arm/mach-lpc32xx/common.h
+++ linux-2.6/arch/arm/mach-lpc32xx/common.h
@@ -23,26 +23,12 @@
#include <linux/platform_device.h>
/*
- * Arch specific platform device structures
- */
-extern struct platform_device lpc32xx_watchdog_device;
-extern struct platform_device lpc32xx_i2c0_device;
-extern struct platform_device lpc32xx_i2c1_device;
-extern struct platform_device lpc32xx_i2c2_device;
-extern struct platform_device lpc32xx_tsc_device;
-extern struct platform_device lpc32xx_adc_device;
-extern struct platform_device lpc32xx_rtc_device;
-extern struct platform_device lpc32xx_ohci_device;
-extern struct platform_device lpc32xx_net_device;
-
-/*
* Other arch specific structures and functions
*/
extern struct sys_timer lpc32xx_timer;
extern void __init lpc32xx_init_irq(void);
extern void __init lpc32xx_map_io(void);
extern void __init lpc32xx_serial_init(void);
-extern void __init lpc32xx_gpio_init(void);
extern void lpc23xx_restart(char, const char *);
--- linux-2.6.orig/arch/arm/mach-lpc32xx/irq.c
+++ linux-2.6/arch/arm/mach-lpc32xx/irq.c
@@ -22,6 +22,11 @@
#include <linux/irq.h>
#include <linux/err.h>
#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
#include <mach/irqs.h>
#include <mach/hardware.h>
@@ -44,6 +49,9 @@
#define SIC1_ATR_DEFAULT 0x00026000
#define SIC2_ATR_DEFAULT 0x00000000
+static struct irq_domain *lpc32xx_mic_domain;
+static struct device_node *lpc32xx_mic_np;
+
struct lpc32xx_event_group_regs {
void __iomem *enab_reg;
void __iomem *edge_reg;
@@ -203,7 +211,7 @@ static void lpc32xx_mask_irq(struct irq_
{
unsigned int reg, ctrl, mask;
- get_controller(d->irq, &ctrl, &mask);
+ get_controller(d->hwirq, &ctrl, &mask);
reg = __raw_readl(LPC32XX_INTC_MASK(ctrl)) & ~mask;
__raw_writel(reg, LPC32XX_INTC_MASK(ctrl));
@@ -213,7 +221,7 @@ static void lpc32xx_unmask_irq(struct ir
{
unsigned int reg, ctrl, mask;
- get_controller(d->irq, &ctrl, &mask);
+ get_controller(d->hwirq, &ctrl, &mask);
reg = __raw_readl(LPC32XX_INTC_MASK(ctrl)) | mask;
__raw_writel(reg, LPC32XX_INTC_MASK(ctrl));
@@ -223,14 +231,14 @@ static void lpc32xx_ack_irq(struct irq_d
{
unsigned int ctrl, mask;
- get_controller(d->irq, &ctrl, &mask);
+ get_controller(d->hwirq, &ctrl, &mask);
__raw_writel(mask, LPC32XX_INTC_RAW_STAT(ctrl));
/* Also need to clear pending wake event */
- if (lpc32xx_events[d->irq].mask != 0)
- __raw_writel(lpc32xx_events[d->irq].mask,
- lpc32xx_events[d->irq].event_group->rawstat_reg);
+ if (lpc32xx_events[d->hwirq].mask != 0)
+ __raw_writel(lpc32xx_events[d->hwirq].mask,
+ lpc32xx_events[d->hwirq].event_group->rawstat_reg);
}
static void __lpc32xx_set_irq_type(unsigned int irq, int use_high_level,
@@ -274,22 +282,22 @@ static int lpc32xx_set_irq_type(struct i
switch (type) {
case IRQ_TYPE_EDGE_RISING:
/* Rising edge sensitive */
- __lpc32xx_set_irq_type(d->irq, 1, 1);
+ __lpc32xx_set_irq_type(d->hwirq, 1, 1);
break;
case IRQ_TYPE_EDGE_FALLING:
/* Falling edge sensitive */
- __lpc32xx_set_irq_type(d->irq, 0, 1);
+ __lpc32xx_set_irq_type(d->hwirq, 0, 1);
break;
case IRQ_TYPE_LEVEL_LOW:
/* Low level sensitive */
- __lpc32xx_set_irq_type(d->irq, 0, 0);
+ __lpc32xx_set_irq_type(d->hwirq, 0, 0);
break;
case IRQ_TYPE_LEVEL_HIGH:
/* High level sensitive */
- __lpc32xx_set_irq_type(d->irq, 1, 0);
+ __lpc32xx_set_irq_type(d->hwirq, 1, 0);
break;
/* Other modes are not supported */
@@ -298,7 +306,7 @@ static int lpc32xx_set_irq_type(struct i
}
/* Ok to use the level handler for all types */
- irq_set_handler(d->irq, handle_level_irq);
+ irq_set_handler(d->hwirq, handle_level_irq);
return 0;
}
@@ -307,33 +315,33 @@ static int lpc32xx_irq_wake(struct irq_d
{
unsigned long eventreg;
- if (lpc32xx_events[d->irq].mask != 0) {
- eventreg = __raw_readl(lpc32xx_events[d->irq].
+ if (lpc32xx_events[d->hwirq].mask != 0) {
+ eventreg = __raw_readl(lpc32xx_events[d->hwirq].
event_group->enab_reg);
if (state)
- eventreg |= lpc32xx_events[d->irq].mask;
+ eventreg |= lpc32xx_events[d->hwirq].mask;
else {
- eventreg &= ~lpc32xx_events[d->irq].mask;
+ eventreg &= ~lpc32xx_events[d->hwirq].mask;
/*
* When disabling the wakeup, clear the latched
* event
*/
- __raw_writel(lpc32xx_events[d->irq].mask,
- lpc32xx_events[d->irq].
+ __raw_writel(lpc32xx_events[d->hwirq].mask,
+ lpc32xx_events[d->hwirq].
event_group->rawstat_reg);
}
__raw_writel(eventreg,
- lpc32xx_events[d->irq].event_group->enab_reg);
+ lpc32xx_events[d->hwirq].event_group->enab_reg);
return 0;
}
/* Clear event */
- __raw_writel(lpc32xx_events[d->irq].mask,
- lpc32xx_events[d->irq].event_group->rawstat_reg);
+ __raw_writel(lpc32xx_events[d->hwirq].mask,
+ lpc32xx_events[d->hwirq].event_group->rawstat_reg);
return -ENODEV;
}
@@ -353,6 +361,7 @@ static void __init lpc32xx_set_default_m
}
static struct irq_chip lpc32xx_irq_chip = {
+ .name = "MIC",
.irq_ack = lpc32xx_ack_irq,
.irq_mask = lpc32xx_mask_irq,
.irq_unmask = lpc32xx_unmask_irq,
@@ -386,9 +395,23 @@ static void lpc32xx_sic2_handler(unsigne
}
}
+static int __init __lpc32xx_mic_of_init(struct device_node *node,
+ struct device_node *parent)
+{
+ lpc32xx_mic_np = node;
+
+ return 0;
+}
+
+static const struct of_device_id mic_of_match[] __initconst = {
+ { .compatible = "nxp,lpc3220-mic", .data = __lpc32xx_mic_of_init },
+ { }
+};
+
void __init lpc32xx_init_irq(void)
{
unsigned int i;
+ int irq_base;
/* Setup MIC */
__raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_MIC_BASE));
@@ -448,4 +471,19 @@ void __init lpc32xx_init_irq(void)
LPC32XX_CLKPWR_PIN_RS);
__raw_writel(__raw_readl(LPC32XX_CLKPWR_INT_RS),
LPC32XX_CLKPWR_INT_RS);
+
+ of_irq_init(mic_of_match);
+
+ irq_base = irq_alloc_descs(-1, 0, NR_IRQS, 0);
+ if (irq_base < 0) {
+ pr_warn("Cannot allocate irq_descs, assuming pre-allocated\n");
+ irq_base = 0;
+ }
+
+ lpc32xx_mic_domain = irq_domain_add_legacy(lpc32xx_mic_np, NR_IRQS,
+ irq_base, 0,
+ &irq_domain_simple_ops,
+ NULL);
+ if (!lpc32xx_mic_domain)
+ panic("Unable to add MIC irq domain\n");
}
--- linux-2.6.orig/arch/arm/mach-lpc32xx/phy3250.c
+++ linux-2.6/arch/arm/mach-lpc32xx/phy3250.c
@@ -1,8 +1,9 @@
/*
- * arch/arm/mach-lpc32xx/phy3250.c
+ * Platform support for LPC32xx SoC
*
* Author: Kevin Wells <kevin.wells at nxp.com>
*
+ * Copyright (C) 2012 Roland Stigge <stigge at antcom.de>
* Copyright (C) 2010 NXP Semiconductors
*
* This program is free software; you can redistribute it and/or modify
@@ -25,11 +26,16 @@
#include <linux/device.h>
#include <linux/spi/spi.h>
#include <linux/spi/eeprom.h>
-#include <linux/leds.h>
#include <linux/gpio.h>
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
#include <linux/amba/pl022.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/clk.h>
+#include <linux/amba/pl08x.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
@@ -47,7 +53,6 @@
#define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
-#define LED_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 1)
/*
* AMBA LCD controller
@@ -150,9 +155,6 @@ static struct clcd_board lpc32xx_clcd_da
.remove = lpc32xx_clcd_remove,
};
-static AMBA_AHB_DEVICE(lpc32xx_clcd, "dev:clcd", 0,
- LPC32XX_LCD_BASE, { IRQ_LPC32XX_LCD }, &lpc32xx_clcd_data);
-
/*
* AMBA SSP (SPI)
*/
@@ -180,8 +182,11 @@ static struct pl022_ssp_controller lpc32
.enable_dma = 0,
};
-static AMBA_APB_DEVICE(lpc32xx_ssp0, "dev:ssp0", 0,
- LPC32XX_SSP0_BASE, { IRQ_LPC32XX_SSP0 }, &lpc32xx_ssp0_data);
+static struct pl022_ssp_controller lpc32xx_ssp1_data = {
+ .bus_id = 1,
+ .num_chipselect = 1,
+ .enable_dma = 0,
+};
/* AT25 driver registration */
static int __init phy3250_spi_board_register(void)
@@ -221,73 +226,20 @@ static int __init phy3250_spi_board_regi
}
arch_initcall(phy3250_spi_board_register);
-static struct i2c_board_info __initdata phy3250_i2c_board_info[] = {
- {
- I2C_BOARD_INFO("pcf8563", 0x51),
- },
+static struct pl08x_platform_data pl08x_pd = {
};
-static struct gpio_led phy_leds[] = {
- {
- .name = "led0",
- .gpio = LED_GPIO,
- .active_low = 1,
- .default_trigger = "heartbeat",
- },
+static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = {
+ OF_DEV_AUXDATA("arm,pl022", 0x20084000, "dev:ssp0", &lpc32xx_ssp0_data),
+ OF_DEV_AUXDATA("arm,pl022", 0x2008C000, "dev:ssp1", &lpc32xx_ssp1_data),
+ OF_DEV_AUXDATA("arm,pl110", 0x31040000, "dev:clcd", &lpc32xx_clcd_data),
+ OF_DEV_AUXDATA("arm,pl080", 0x31000000, "pl08xdmac", &pl08x_pd),
+ { }
};
-static struct gpio_led_platform_data led_data = {
- .leds = phy_leds,
- .num_leds = ARRAY_SIZE(phy_leds),
-};
-
-static struct platform_device lpc32xx_gpio_led_device = {
- .name = "leds-gpio",
- .id = -1,
- .dev.platform_data = &led_data,
-};
-
-static struct platform_device *phy3250_devs[] __initdata = {
- &lpc32xx_rtc_device,
- &lpc32xx_tsc_device,
- &lpc32xx_i2c0_device,
- &lpc32xx_i2c1_device,
- &lpc32xx_i2c2_device,
- &lpc32xx_watchdog_device,
- &lpc32xx_gpio_led_device,
- &lpc32xx_adc_device,
- &lpc32xx_ohci_device,
- &lpc32xx_net_device,
-};
-
-static struct amba_device *amba_devs[] __initdata = {
- &lpc32xx_clcd_device,
- &lpc32xx_ssp0_device,
-};
-
-/*
- * Board specific functions
- */
-static void __init phy3250_board_init(void)
+static void __init lpc3250_machine_init(void)
{
u32 tmp;
- int i;
-
- lpc32xx_gpio_init();
-
- /* Register GPIOs used on this board */
- if (gpio_request(SPI0_CS_GPIO, "spi0 cs"))
- printk(KERN_ERR "Error requesting gpio %u",
- SPI0_CS_GPIO);
- else if (gpio_direction_output(SPI0_CS_GPIO, 1))
- printk(KERN_ERR "Error setting gpio %u to output",
- SPI0_CS_GPIO);
-
- /* Setup network interface for RMII mode */
- tmp = __raw_readl(LPC32XX_CLKPWR_MACCLK_CTRL);
- tmp &= ~LPC32XX_CLKPWR_MACCTRL_PINS_MSK;
- tmp |= LPC32XX_CLKPWR_MACCTRL_USE_RMII_PINS;
- __raw_writel(tmp, LPC32XX_CLKPWR_MACCLK_CTRL);
/* Setup SLC NAND controller muxing */
__raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
@@ -300,6 +252,12 @@ static void __init phy3250_board_init(vo
tmp |= LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT16;
__raw_writel(tmp, LPC32XX_CLKPWR_LCDCLK_CTRL);
+ /* Set up USB power */
+ tmp = __raw_readl(LPC32XX_CLKPWR_USB_CTRL);
+ tmp |= LPC32XX_CLKPWR_USBCTRL_HCLK_EN |
+ LPC32XX_CLKPWR_USBCTRL_USBI2C_EN;
+ __raw_writel(tmp, LPC32XX_CLKPWR_USB_CTRL);
+
/* Set up I2C pull levels */
tmp = __raw_readl(LPC32XX_CLKPWR_I2C_CLK_CTRL);
tmp |= LPC32XX_CLKPWR_I2CCLK_USBI2CHI_DRIVE |
@@ -321,33 +279,35 @@ static void __init phy3250_board_init(vo
/*
* AMBA peripheral clocks need to be enabled prior to AMBA device
* detection or a data fault will occur, so enable the clocks
- * here. However, we don't want to enable them if the peripheral
- * isn't included in the image
+ * here.
*/
-#ifdef CONFIG_FB_ARMCLCD
tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL);
__raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN),
LPC32XX_CLKPWR_LCDCLK_CTRL);
-#endif
-#ifdef CONFIG_SPI_PL022
+
tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL);
__raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN),
LPC32XX_CLKPWR_SSP_CLK_CTRL);
-#endif
- platform_add_devices(phy3250_devs, ARRAY_SIZE(phy3250_devs));
- for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
- struct amba_device *d = amba_devs[i];
- amba_device_register(d, &iomem_resource);
- }
+ tmp = __raw_readl(LPC32XX_CLKPWR_DMA_CLK_CTRL);
+ __raw_writel((tmp | LPC32XX_CLKPWR_DMACLKCTRL_CLK_EN),
+ LPC32XX_CLKPWR_DMA_CLK_CTRL);
/* Test clock needed for UDA1380 initial init */
__raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC |
LPC32XX_CLKPWR_TESTCLK_TESTCLK2_EN,
LPC32XX_CLKPWR_TEST_CLK_SEL);
- i2c_register_board_info(0, phy3250_i2c_board_info,
- ARRAY_SIZE(phy3250_i2c_board_info));
+ of_platform_populate(NULL, of_default_bus_match_table,
+ lpc32xx_auxdata_lookup, NULL);
+
+ /* Register GPIOs used on this board */
+ if (gpio_request(SPI0_CS_GPIO, "spi0 cs"))
+ printk(KERN_ERR "Error requesting gpio %u",
+ SPI0_CS_GPIO);
+ else if (gpio_direction_output(SPI0_CS_GPIO, 1))
+ printk(KERN_ERR "Error setting gpio %u to output",
+ SPI0_CS_GPIO);
}
static int __init lpc32xx_display_uid(void)
@@ -363,12 +323,20 @@ static int __init lpc32xx_display_uid(vo
}
arch_initcall(lpc32xx_display_uid);
-MACHINE_START(PHY3250, "Phytec 3250 board with the LPC3250 Microcontroller")
- /* Maintainer: Kevin Wells, NXP Semiconductors */
+static char const *lpc32xx_dt_compat[] __initdata = {
+ "nxp,lpc3220",
+ "nxp,lpc3230",
+ "nxp,lpc3240",
+ "nxp,lpc3250",
+ NULL
+};
+
+DT_MACHINE_START(LPC32XX_DT, "LPC32XX SoC (Flattened Device Tree)")
.atag_offset = 0x100,
.map_io = lpc32xx_map_io,
.init_irq = lpc32xx_init_irq,
.timer = &lpc32xx_timer,
- .init_machine = phy3250_board_init,
+ .init_machine = lpc3250_machine_init,
+ .dt_compat = lpc32xx_dt_compat,
.restart = lpc23xx_restart,
MACHINE_END
More information about the linux-arm-kernel
mailing list