[PATCH 08/10] MXS: Add separate MXS EHCI HCD driver

[Sascha Hauer]

On Wed, Apr 18, 2012 at 07:46:32PM +0200, Marek Vasut wrote:
> This driver will handle i.MX233/i.MX28 and I hope soon i.MX6Q. I tried to keep
> this separate from the MXC EHCI to avoid further polution of the MXC EHCI,
> though eventually these two might be merged.
> 
> NOTE: I still haven't figured out how to enable/disable the disconnection
> detector, it can't be enabled all the time, so I toggle PHY stuff from this
> driver, which I doubt is correct.
> 

[...]

> +static int ehci_mxs_drv_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct imx_usb *data = pdev->dev.platform_data;
> +	struct usb_hcd *hcd;
> +	struct ehci_hcd *ehci;
> +	struct usb_phy *phy;
> +	int ret;
> +
> +	dev_info(dev, "Initializing i.MX28 USB Controller\n");

This is not (only) i.MX28

> +
> +	if (!data) {
> +		dev_err(dev, "USB Host platform data missing!\n");
> +		return -ENODEV;
> +	}
> +
> +	/* Create HCD controller instance. */
> +	hcd = usb_create_hcd(&ehci_mxs_hc_driver, dev, dev_name(dev));
> +	if (!hcd) {
> +		dev_err(dev, "Failed to create HCD instance!\n");
> +		return -ENOMEM;
> +	}
> +
> +	hcd->rsrc_start = data->mem_res->start;
> +	hcd->rsrc_len = resource_size(data->mem_res);
> +	hcd->regs = data->mem;
> +	hcd->irq = data->irq;
> +
> +	clk_enable(data->clk);

The clock shouldn't be here. move this to imx-otg.c

> +
> +	/* Wait for the controller to stabilize. */
> +	mdelay(10);
> +
> +	ehci = hcd_to_ehci(hcd);
> +
> +	/* EHCI registers start at offset 0x100 */
> +	ehci->caps = hcd->regs + 0x100;
> +	ehci->regs = hcd->regs + 0x100 +
> +		HC_LENGTH(ehci, ehci_readl(ehci, &ehci->caps->hc_capbase));
> +
> +	platform_set_drvdata(pdev, hcd);
> +
> +	/* Initialize the transceiver */
> +#ifdef CONFIG_USB_OTG_UTILS
> +	phy = usb_get_transceiver();
> +	if (!phy) {
> +		dev_err(dev, "Unable to find transceiver.\n");
> +		ret = -ENODEV;
> +		goto err_phy;
> +	}
> +
> +	ret = otg_set_host(phy->otg, &hcd->self);
> +	if (ret < 0) {
> +		dev_err(dev, "Unable to set transceiver host\n");
> +		ret = -ENODEV;
> +		goto err_phy_set_host;
> +	}
> +
> +	ret = usb_phy_init(phy);
> +	if (ret < 0) {
> +		dev_err(dev, "Unable init transceiver\n");
> +		ret = -ENODEV;
> +		goto err_phy_init;
> +	}
> +#else
> +	dev_info(dev, "USB_MXS_PHY must have CONFIG_USB_OTG_UTILS enabled\n");
> +	goto err_phy;
> +#endif

If your code does not work without CONFIG_USB_OTG_UTILS then why doesn't
the driver depend on this option?
It doesn't matter, all code inside these ifdefs should go to imx-otg.c.

> +
> +	/* Set up the PORTSCx register */
> +	ehci_writel(ehci, 0, &ehci->regs->port_status[0]);
> +

Should also be in imx-otg.c

> +err_phy_init:
> +err_phy_set_host:
> +#ifdef CONFIG_USB_OTG_UTILS
> +	if (phy)
> +		usb_put_transceiver(phy);
> +#endif
> +err_phy:
> +	clk_disable(data->clk);
> +	usb_put_hcd(hcd);
> +	return ret;
> +}
> +
> +static int __exit ehci_mxs_drv_remove(struct platform_device *pdev)
> +{
> +	struct imx_usb *data = pdev->dev.platform_data;
> +	struct usb_hcd *hcd = platform_get_drvdata(pdev);
> +	struct usb_phy *phy = usb_get_transceiver();
> +
> +	if (phy)
> +		usb_phy_shutdown(phy);
> +
> +	usb_remove_hcd(hcd);

usb_add_hcd is in imx-otg.c so usb_remove_hcd should be aswell.

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |