[PATCH 2/4] AT91: Add machine header file for AT91SAM9N12 SoC
Hong Xu
hong.xu at atmel.com
Thu Apr 12 02:26:34 EDT 2012
Signed-off-by: Hong Xu <hong.xu at atmel.com>
---
arch/arm/mach-at91/include/mach/at91sam9n12.h | 68 ++++++++++++++++++++
.../mach-at91/include/mach/at91sam9n12_matrix.h | 53 +++++++++++++++
arch/arm/mach-at91/include/mach/cpu.h | 10 +++
arch/arm/mach-at91/include/mach/hardware.h | 2 +
arch/arm/mach-at91/soc.h | 5 ++
5 files changed, 138 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-at91/include/mach/at91sam9n12.h
create mode 100644 arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h
diff --git a/arch/arm/mach-at91/include/mach/at91sam9n12.h b/arch/arm/mach-at91/include/mach/at91sam9n12.h
new file mode 100644
index 0000000..ff14bbf
--- /dev/null
+++ b/arch/arm/mach-at91/include/mach/at91sam9n12.h
@@ -0,0 +1,68 @@
+/*
+ * SoC specific header file for the AT91SAM9N12
+ *
+ * Copyright (C) 2012 Atmel Corporation
+ *
+ * Common definitions, based on AT91SAM9N12 SoC datasheet
+ *
+ * Licensed under GPLv2 or later
+ */
+
+#ifndef _AT91SAM9N12_H_
+#define _AT91SAM9N12_H_
+
+/*
+ * Peripheral identifiers/interrupts.
+ */
+#define AT91SAM9N12_ID_PIOAB 2 /* Parallel I/O Controller A and B */
+#define AT91SAM9N12_ID_PIOCD 3 /* Parallel I/O Controller C and D */
+#define AT91SAM9N12_ID_FUSE 4 /* FUSE Controller */
+#define AT91SAM9N12_ID_USART0 5 /* USART 0 */
+#define AT91SAM9N12_ID_USART1 6 /* USART 1 */
+#define AT91SAM9N12_ID_USART2 7 /* USART 2 */
+#define AT91SAM9N12_ID_USART3 8 /* USART 3 */
+#define AT91SAM9N12_ID_TWI0 9 /* Two-Wire Interface 0 */
+#define AT91SAM9N12_ID_TWI1 10 /* Two-Wire Interface 1 */
+#define AT91SAM9N12_ID_MCI 12 /* High Speed Multimedia Card Interface */
+#define AT91SAM9N12_ID_SPI0 13 /* Serial Peripheral Interface 0 */
+#define AT91SAM9N12_ID_SPI1 14 /* Serial Peripheral Interface 1 */
+#define AT91SAM9N12_ID_UART0 15 /* UART 0 */
+#define AT91SAM9N12_ID_UART1 16 /* UART 1 */
+#define AT91SAM9N12_ID_TCB 17 /* Timer Counter 0, 1, 2, 3, 4 and 5 */
+#define AT91SAM9N12_ID_PWM 18 /* Pulse Width Modulation Controller */
+#define AT91SAM9N12_ID_ADC 19 /* ADC Controller */
+#define AT91SAM9N12_ID_DMA 20 /* DMA Controller */
+#define AT91SAM9N12_ID_UHP 22 /* USB Host High Speed */
+#define AT91SAM9N12_ID_UDP 23 /* USB Device High Speed */
+#define AT91SAM9N12_ID_LCDC 25 /* LCD Controller */
+#define AT91SAM9N12_ID_ISI 25 /* Image Sensor Interface */
+#define AT91SAM9N12_ID_SSC 28 /* Synchronous Serial Controller */
+#define AT91SAM9N12_ID_TRNG 30 /* TRNG */
+#define AT91SAM9N12_ID_IRQ0 31 /* Advanced Interrupt Controller */
+
+/*
+ * User Peripheral physical base addresses.
+ */
+#define AT91SAM9N12_BASE_USART0 0xf801c000
+#define AT91SAM9N12_BASE_USART1 0xf8020000
+#define AT91SAM9N12_BASE_USART2 0xf8024000
+#define AT91SAM9N12_BASE_USART3 0xf8028000
+
+/*
+ * Base addresses for early serial code (uncompress.h)
+ */
+#define AT91_DBGU AT91_BASE_DBGU0
+#define AT91_USART0 AT91SAM9N12_BASE_USART0
+#define AT91_USART1 AT91SAM9N12_BASE_USART1
+#define AT91_USART2 AT91SAM9N12_BASE_USART2
+
+/*
+ * Internal Memory.
+ */
+#define AT91SAM9N12_SRAM_BASE 0x00300000 /* Internal SRAM base address */
+#define AT91SAM9N12_SRAM_SIZE SZ_32K /* Internal SRAM size (32Kb) */
+
+#define AT91SAM9N12_ROM_BASE 0x00100000 /* Internal ROM base address */
+#define AT91SAM9N12_ROM_SIZE SZ_128K /* Internal ROM size (128Kb) */
+
+#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h
new file mode 100644
index 0000000..40060cd
--- /dev/null
+++ b/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h
@@ -0,0 +1,53 @@
+/*
+ * Matrix-centric header file for the AT91SAM9N12
+ *
+ * Copyright (C) 2012 Atmel Corporation.
+ *
+ * Only EBI related registers.
+ * Write Protect register definitions may be useful.
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#ifndef _AT91SAM9N12_MATRIX_H_
+#define _AT91SAM9N12_MATRIX_H_
+
+#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x118) /* EBI Chip Select Assignment Register */
+#define AT91_MATRIX_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */
+#define AT91_MATRIX_EBI_CS1A_SMC (0 << 1)
+#define AT91_MATRIX_EBI_CS1A_SDRAMC (1 << 1)
+#define AT91_MATRIX_EBI_CS3A (1 << 3) /* Chip Select 3 Assignment */
+#define AT91_MATRIX_EBI_CS3A_SMC (0 << 3)
+#define AT91_MATRIX_EBI_CS3A_SMC_NANDFLASH (1 << 3)
+#define AT91_MATRIX_EBI_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */
+#define AT91_MATRIX_EBI_DBPU_ON (0 << 8)
+#define AT91_MATRIX_EBI_DBPU_OFF (1 << 8)
+#define AT91_MATRIX_EBI_VDDIOMSEL (1 << 16) /* Memory voltage selection */
+#define AT91_MATRIX_EBI_VDDIOMSEL_1_8V (0 << 16)
+#define AT91_MATRIX_EBI_VDDIOMSEL_3_3V (1 << 16)
+#define AT91_MATRIX_EBI_EBI_IOSR (1 << 17) /* EBI I/O slew rate selection */
+#define AT91_MATRIX_EBI_EBI_IOSR_REDUCED (0 << 17)
+#define AT91_MATRIX_EBI_EBI_IOSR_NORMAL (1 << 17)
+#define AT91_MATRIX_EBI_DDR_IOSR (1 << 18) /* DDR2 dedicated port I/O slew rate selection */
+#define AT91_MATRIX_EBI_DDR_IOSR_REDUCED (0 << 18)
+#define AT91_MATRIX_EBI_DDR_IOSR_NORMAL (1 << 18)
+#define AT91_MATRIX_NFD0_SELECT (1 << 24) /* NAND Flash Data Bus Selection */
+#define AT91_MATRIX_NFD0_ON_D0 (0 << 24)
+#define AT91_MATRIX_NFD0_ON_D16 (1 << 24)
+#define AT91_MATRIX_DDR_MP_EN (1 << 25) /* DDR Multi-port Enable */
+#define AT91_MATRIX_MP_OFF (0 << 25)
+#define AT91_MATRIX_MP_ON (1 << 25)
+
+#define AT91_MATRIX_WPMR (AT91_MATRIX + 0x1E4) /* Write Protect Mode Register */
+#define AT91_MATRIX_WPMR_WPEN (1 << 0) /* Write Protect ENable */
+#define AT91_MATRIX_WPMR_WP_WPDIS (0 << 0)
+#define AT91_MATRIX_WPMR_WP_WPEN (1 << 0)
+#define AT91_MATRIX_WPMR_WPKEY (0xFFFFFF << 8) /* Write Protect KEY */
+
+#define AT91_MATRIX_WPSR (AT91_MATRIX + 0x1E8) /* Write Protect Status Register */
+#define AT91_MATRIX_WPSR_WPVS (1 << 0) /* Write Protect Violation Status */
+#define AT91_MATRIX_WPSR_NO_WPV (0 << 0)
+#define AT91_MATRIX_WPSR_WPV (1 << 0)
+#define AT91_MATRIX_WPSR_WPVSRC (0xFFFF << 8) /* Write Protect Violation Source */
+
+#endif
diff --git a/arch/arm/mach-at91/include/mach/cpu.h b/arch/arm/mach-at91/include/mach/cpu.h
index 0118c33..c7c64e9 100644
--- a/arch/arm/mach-at91/include/mach/cpu.h
+++ b/arch/arm/mach-at91/include/mach/cpu.h
@@ -25,6 +25,7 @@
#define ARCH_ID_AT91SAM9G45MRL 0x819b05a2 /* aka 9G45-ES2 & non ES lots */
#define ARCH_ID_AT91SAM9G45ES 0x819b05a1 /* 9G45-ES (Engineering Sample) */
#define ARCH_ID_AT91SAM9X5 0x819a05a0
+#define ARCH_ID_AT91SAM9N12 0x819a07a0
#define ARCH_ID_AT91SAM9XE128 0x329973a0
#define ARCH_ID_AT91SAM9XE256 0x329a93a0
@@ -70,6 +71,9 @@ enum at91_soc_type {
/* SAM9X5 */
AT91_SOC_SAM9X5,
+ /* SAM9N12 */
+ AT91_SOC_SAM9N12,
+
/* Unknown type */
AT91_SOC_NONE
};
@@ -184,6 +188,12 @@ static inline int at91_soc_is_detected(void)
#define cpu_is_at91sam9x25() (0)
#endif
+#ifdef CONFIG_ARCH_AT91SAM9N12
+#define cpu_is_at91sam9n12() (at91_soc_initdata.type == AT91_SOC_SAM9N12)
+#else
+#define cpu_is_at91sam9n12() (0)
+#endif
+
/*
* Since this is ARM, we will never run on any AVR32 CPU. But these
* definitions may reduce clutter in common drivers.
diff --git a/arch/arm/mach-at91/include/mach/hardware.h b/arch/arm/mach-at91/include/mach/hardware.h
index e9e29a6..39a5654 100644
--- a/arch/arm/mach-at91/include/mach/hardware.h
+++ b/arch/arm/mach-at91/include/mach/hardware.h
@@ -36,6 +36,8 @@
#include <mach/at91sam9g45.h>
#elif defined(CONFIG_ARCH_AT91SAM9X5)
#include <mach/at91sam9x5.h>
+#elif defined(CONFIG_ARCH_AT91SAM9N12)
+#include <mach/at91sam9n12.h>
#elif defined(CONFIG_ARCH_AT91X40)
#include <mach/at91x40.h>
#else
diff --git a/arch/arm/mach-at91/soc.h b/arch/arm/mach-at91/soc.h
index 5db4aa4..0e3fcb8 100644
--- a/arch/arm/mach-at91/soc.h
+++ b/arch/arm/mach-at91/soc.h
@@ -20,6 +20,7 @@ extern struct at91_init_soc at91sam9263_soc;
extern struct at91_init_soc at91sam9g45_soc;
extern struct at91_init_soc at91sam9rl_soc;
extern struct at91_init_soc at91sam9x5_soc;
+extern struct at91_init_soc at91sam9n12_soc;
static inline int at91_soc_is_enabled(void)
{
@@ -53,3 +54,7 @@ static inline int at91_soc_is_enabled(void)
#if !defined(CONFIG_ARCH_AT91SAM9X5)
#define at91sam9x5_soc at91_boot_soc
#endif
+
+#if !defined(CONFIG_ARCH_AT91SAM9N12)
+#define at91sam9n12_soc at91_boot_soc
+#endif
--
1.7.3.3
More information about the linux-arm-kernel
mailing list