[PATCH v2] ARM: dts: imx6q: add anatop regulators

[Shawn Guo]

On Fri, Mar 30, 2012 at 09:46:53PM +0800, Ying-Chun Liu (PaulLiu) wrote:
> From: "Ying-Chun Liu (PaulLiu)" <paul.liu at linaro.org>
> 
> Add anatop regulators to imx6q.dtsi for all imx6q platforms.
> 
> Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu at linaro.org>
> Signed-off-by: Richard Zhao <richard.zhao at linaro.org>
> Cc: Shawn Guo <shawn.guo at linaro.org>
> ---
>  arch/arm/boot/dts/imx6q.dtsi |   86 ++++++++++++++++++++++++++++++++++++++++++
>  1 files changed, 86 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
> index 263e8f3..79f59e7 100644
> --- a/arch/arm/boot/dts/imx6q.dtsi
> +++ b/arch/arm/boot/dts/imx6q.dtsi
> @@ -346,6 +346,92 @@
>  				compatible = "fsl,imx6q-anatop";
>  				reg = <0x020c8000 0x1000>;
>  				interrupts = <0 49 0x04 0 54 0x04 0 127 0x04>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;

These two lines are not needed now.  Removed them and applied the
patch.  Thanks.

Regards,
Shawn

> +
> +				regulator-1p1 at 110 {
> +					compatible = "fsl,anatop-regulator";
> +					regulator-name = "vdd1p1";
> +					regulator-min-microvolt = <800000>;
> +					regulator-max-microvolt = <1375000>;
> +					regulator-always-on;
> +					anatop-reg-offset = <0x110>;
> +					anatop-vol-bit-shift = <8>;
> +					anatop-vol-bit-width = <5>;
> +					anatop-min-bit-val = <4>;
> +					anatop-min-voltage = <800000>;
> +					anatop-max-voltage = <1375000>;
> +				};
> +
> +				regulator-3p0 at 120 {
> +					compatible = "fsl,anatop-regulator";
> +					regulator-name = "vdd3p0";
> +					regulator-min-microvolt = <2800000>;
> +					regulator-max-microvolt = <3150000>;
> +					regulator-always-on;
> +					anatop-reg-offset = <0x120>;
> +					anatop-vol-bit-shift = <8>;
> +					anatop-vol-bit-width = <5>;
> +					anatop-min-bit-val = <0>;
> +					anatop-min-voltage = <2625000>;
> +					anatop-max-voltage = <3400000>;
> +				};
> +
> +				regulator-2p5 at 130 {
> +					compatible = "fsl,anatop-regulator";
> +					regulator-name = "vdd2p5";
> +					regulator-min-microvolt = <2000000>;
> +					regulator-max-microvolt = <2750000>;
> +					regulator-always-on;
> +					anatop-reg-offset = <0x130>;
> +					anatop-vol-bit-shift = <8>;
> +					anatop-vol-bit-width = <5>;
> +					anatop-min-bit-val = <0>;
> +					anatop-min-voltage = <2000000>;
> +					anatop-max-voltage = <2750000>;
> +				};
> +
> +				regulator-vddcore at 140 {
> +					compatible = "fsl,anatop-regulator";
> +					regulator-name = "cpu";
> +					regulator-min-microvolt = <725000>;
> +					regulator-max-microvolt = <1450000>;
> +					regulator-always-on;
> +					anatop-reg-offset = <0x140>;
> +					anatop-vol-bit-shift = <0>;
> +					anatop-vol-bit-width = <5>;
> +					anatop-min-bit-val = <1>;
> +					anatop-min-voltage = <725000>;
> +					anatop-max-voltage = <1450000>;
> +				};
> +
> +				regulator-vddpu at 140 {
> +					compatible = "fsl,anatop-regulator";
> +					regulator-name = "vddpu";
> +					regulator-min-microvolt = <725000>;
> +					regulator-max-microvolt = <1450000>;
> +					regulator-always-on;
> +					anatop-reg-offset = <0x140>;
> +					anatop-vol-bit-shift = <9>;
> +					anatop-vol-bit-width = <5>;
> +					anatop-min-bit-val = <1>;
> +					anatop-min-voltage = <725000>;
> +					anatop-max-voltage = <1450000>;
> +				};
> +
> +				regulator-vddsoc at 140 {
> +					compatible = "fsl,anatop-regulator";
> +					regulator-name = "vddsoc";
> +					regulator-min-microvolt = <725000>;
> +					regulator-max-microvolt = <1450000>;
> +					regulator-always-on;
> +					anatop-reg-offset = <0x140>;
> +					anatop-vol-bit-shift = <18>;
> +					anatop-vol-bit-width = <5>;
> +					anatop-min-bit-val = <1>;
> +					anatop-min-voltage = <725000>;
> +					anatop-max-voltage = <1450000>;
> +				};
>  			};
>  
>  			usbphy at 020c9000 { /* USBPHY1 */
> -- 
> 1.7.9.1
>