[PATCH 2/3 correction] ARM:simpad: Cleanup CS3 accessors.
Jochen Friedrich
jochen at scram.de
Sun Jan 23 13:10:53 EST 2011
- prepend CS3 accessors by simpad_ to indicate they
are specific to simpad devices.
- use spinlock to protect shadow register.
- implement 8 read-only pins.
- use readl/writel macros so barriers are used where
necessary.
- register CS3 as GPIO controller with 24 pins
(16 output only and 8 input only).
Signed-off-by: Jochen Friedrich <jochen at scram.de>
---
arch/arm/mach-sa1100/include/mach/simpad.h | 81 ++++++++++++++------
arch/arm/mach-sa1100/leds-simpad.c | 7 +-
arch/arm/mach-sa1100/simpad.c | 115 ++++++++++++++++++++++------
drivers/pcmcia/sa1100_simpad.c | 30 +++----
4 files changed, 165 insertions(+), 68 deletions(-)
diff --git a/arch/arm/mach-sa1100/include/mach/simpad.h b/arch/arm/mach-sa1100/include/mach/simpad.h
index 231550d..db28118 100644
--- a/arch/arm/mach-sa1100/include/mach/simpad.h
+++ b/arch/arm/mach-sa1100/include/mach/simpad.h
@@ -61,32 +61,67 @@
#define SIMPAD_UCB1X00_GPIO_HEADSET (SIMPAD_UCB1X00_GPIO_BASE + 8)
#define SIMPAD_UCB1X00_GPIO_SPEAKER (SIMPAD_UCB1X00_GPIO_BASE + 9)
-// CS3 Latch is write only, a shadow is necessary
+/*--- CS3 Latch ---*/
+#define SIMPAD_CS3_GPIO_BASE (GPIO_MAX + 11)
+#define SIMPAD_CS3_VCC_5V_EN (SIMPAD_CS3_GPIO_BASE)
+#define SIMPAD_CS3_VCC_3V_EN (SIMPAD_CS3_GPIO_BASE + 1)
+#define SIMPAD_CS3_EN1 (SIMPAD_CS3_GPIO_BASE + 2)
+#define SIMPAD_CS3_EN0 (SIMPAD_CS3_GPIO_BASE + 3)
+#define SIMPAD_CS3_DISPLAY_ON (SIMPAD_CS3_GPIO_BASE + 4)
+#define SIMPAD_CS3_PCMCIA_BUFF_DIS (SIMPAD_CS3_GPIO_BASE + 5)
+#define SIMPAD_CS3_MQ_RESET (SIMPAD_CS3_GPIO_BASE + 6)
+#define SIMPAD_CS3_PCMCIA_RESET (SIMPAD_CS3_GPIO_BASE + 7)
+#define SIMPAD_CS3_DECT_POWER_ON (SIMPAD_CS3_GPIO_BASE + 8)
+#define SIMPAD_CS3_IRDA_SD (SIMPAD_CS3_GPIO_BASE + 9)
+#define SIMPAD_CS3_RS232_ON (SIMPAD_CS3_GPIO_BASE + 10)
+#define SIMPAD_CS3_SD_MEDIAQ (SIMPAD_CS3_GPIO_BASE + 11)
+#define SIMPAD_CS3_LED2_ON (SIMPAD_CS3_GPIO_BASE + 12)
+#define SIMPAD_CS3_IRDA_MODE (SIMPAD_CS3_GPIO_BASE + 13)
+#define SIMPAD_CS3_ENABLE_5V (SIMPAD_CS3_GPIO_BASE + 14)
+#define SIMPAD_CS3_RESET_SIMCARD (SIMPAD_CS3_GPIO_BASE + 15)
+
+#define SIMPAD_CS3_PCMCIA_BVD1 (SIMPAD_CS3_GPIO_BASE + 16)
+#define SIMPAD_CS3_PCMCIA_BVD2 (SIMPAD_CS3_GPIO_BASE + 17)
+#define SIMPAD_CS3_PCMCIA_VS1 (SIMPAD_CS3_GPIO_BASE + 18)
+#define SIMPAD_CS3_PCMCIA_VS2 (SIMPAD_CS3_GPIO_BASE + 19)
+#define SIMPAD_CS3_LOCK_IND (SIMPAD_CS3_GPIO_BASE + 20)
+#define SIMPAD_CS3_CHARGING_STATE (SIMPAD_CS3_GPIO_BASE + 21)
+#define SIMPAD_CS3_PCMCIA_SHORT (SIMPAD_CS3_GPIO_BASE + 22)
+#define SIMPAD_CS3_GPIO_23 (SIMPAD_CS3_GPIO_BASE + 23)
-#define CS3BUSTYPE unsigned volatile long
#define CS3_BASE 0xf1000000
-#define VCC_5V_EN 0x0001 // For 5V PCMCIA
-#define VCC_3V_EN 0x0002 // FOR 3.3V PCMCIA
-#define EN1 0x0004 // This is only for EPROM's
-#define EN0 0x0008 // Both should be enable for 3.3V or 5V
-#define DISPLAY_ON 0x0010
-#define PCMCIA_BUFF_DIS 0x0020
-#define MQ_RESET 0x0040
-#define PCMCIA_RESET 0x0080
-#define DECT_POWER_ON 0x0100
-#define IRDA_SD 0x0200 // Shutdown for powersave
-#define RS232_ON 0x0400
-#define SD_MEDIAQ 0x0800 // Shutdown for powersave
-#define LED2_ON 0x1000
-#define IRDA_MODE 0x2000 // Fast/Slow IrDA mode
-#define ENABLE_5V 0x4000 // Enable 5V circuit
-#define RESET_SIMCARD 0x8000
-
-#define RS232_ENABLE 0x0440
-#define PCMCIAMASK 0x402f
-
-
+long simpad_get_cs3_ro(void);
+long simpad_get_cs3_shadow(void);
+void simpad_set_cs3_bit(int value);
+void simpad_clear_cs3_bit(int value);
+
+#define VCC_5V_EN 0x0001 /* For 5V PCMCIA */
+#define VCC_3V_EN 0x0002 /* FOR 3.3V PCMCIA */
+#define EN1 0x0004 /* This is only for EPROM's */
+#define EN0 0x0008 /* Both should be enable for 3.3V or 5V */
+#define DISPLAY_ON 0x0010
+#define PCMCIA_BUFF_DIS 0x0020
+#define MQ_RESET 0x0040
+#define PCMCIA_RESET 0x0080
+#define DECT_POWER_ON 0x0100
+#define IRDA_SD 0x0200 /* Shutdown for powersave */
+#define RS232_ON 0x0400
+#define SD_MEDIAQ 0x0800 /* Shutdown for powersave */
+#define LED2_ON 0x1000
+#define IRDA_MODE 0x2000 /* Fast/Slow IrDA mode */
+#define ENABLE_5V 0x4000 /* Enable 5V circuit */
+#define RESET_SIMCARD 0x8000
+
+#define PCMCIA_BVD1 0x01
+#define PCMCIA_BVD2 0x02
+#define PCMCIA_VS1 0x04
+#define PCMCIA_VS2 0x08
+#define LOCK_IND 0x10
+#define CHARGING_STATE 0x20
+#define PCMCIA_SHORT 0x40
+
+/*--- Battery ---*/
struct simpad_battery {
unsigned char ac_status; /* line connected yes/no */
unsigned char status; /* battery loading yes/no */
diff --git a/arch/arm/mach-sa1100/leds-simpad.c b/arch/arm/mach-sa1100/leds-simpad.c
index d50f4ee..d25784c 100644
--- a/arch/arm/mach-sa1100/leds-simpad.c
+++ b/arch/arm/mach-sa1100/leds-simpad.c
@@ -22,9 +22,6 @@ static unsigned int hw_led_state;
#define LED_GREEN (1)
#define LED_MASK (1)
-extern void set_cs3_bit(int value);
-extern void clear_cs3_bit(int value);
-
void simpad_leds_event(led_event_t evt)
{
switch (evt)
@@ -93,8 +90,8 @@ void simpad_leds_event(led_event_t evt)
}
if (led_state & LED_STATE_ENABLED)
- set_cs3_bit(LED2_ON);
+ simpad_set_cs3_bit(LED2_ON);
else
- clear_cs3_bit(LED2_ON);
+ simpad_clear_cs3_bit(LED2_ON);
}
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index 718b802..ec6e381 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -13,6 +13,7 @@
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/io.h>
+#include <linux/gpio.h>
#include <asm/irq.h>
#include <mach/hardware.h>
@@ -31,32 +32,85 @@
#include "generic.h"
-long cs3_shadow;
+/*
+ * CS3 support
+ */
+
+static long cs3_shadow;
+static spinlock_t cs3_lock;
+static struct gpio_chip cs3_gpio;
+
+long simpad_get_cs3_ro(void)
+{
+ return readl(CS3_BASE);
+}
+EXPORT_SYMBOL(simpad_get_cs3_ro);
-long get_cs3_shadow(void)
+long simpad_get_cs3_shadow(void)
{
return cs3_shadow;
}
+EXPORT_SYMBOL(simpad_get_cs3_shadow);
-void set_cs3(long value)
+static void __simpad_write_cs3(void)
{
- *(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow = value;
+ writel(cs3_shadow, CS3_BASE);
}
-void set_cs3_bit(int value)
+void simpad_set_cs3_bit(int value)
{
+ unsigned long flags;
+
+ spin_lock_irqsave(&cs3_lock, flags);
cs3_shadow |= value;
- *(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow;
+ __simpad_write_cs3();
+ spin_unlock_irqrestore(&cs3_lock, flags);
}
+EXPORT_SYMBOL(simpad_set_cs3_bit);
-void clear_cs3_bit(int value)
+void simpad_clear_cs3_bit(int value)
{
+ unsigned long flags;
+
+ spin_lock_irqsave(&cs3_lock, flags);
cs3_shadow &= ~value;
- *(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow;
+ __simpad_write_cs3();
+ spin_unlock_irqrestore(&cs3_lock, flags);
}
+EXPORT_SYMBOL(simpad_clear_cs3_bit);
+
+static void cs3_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ if (offset > 15)
+ return;
+ if (value)
+ simpad_set_cs3_bit(1 << offset);
+ else
+ simpad_clear_cs3_bit(1 << offset);
+};
-EXPORT_SYMBOL(set_cs3_bit);
-EXPORT_SYMBOL(clear_cs3_bit);
+static int cs3_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ if (offset > 15)
+ return simpad_get_cs3_ro() & (1 << (offset - 16));
+ return simpad_get_cs3_shadow() & (1 << offset);
+};
+
+static int cs3_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+ if (offset > 15)
+ return 0;
+ return -EINVAL;
+};
+
+static int cs3_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+ int value)
+{
+ if (offset > 15)
+ return -EINVAL;
+ cs3_gpio_set(chip, offset, value);
+ return 0;
+};
static struct map_desc simpad_io_desc[] __initdata = {
{ /* MQ200 */
@@ -64,9 +118,9 @@ static struct map_desc simpad_io_desc[] __initdata = {
.pfn = __phys_to_pfn(0x4b800000),
.length = 0x00800000,
.type = MT_DEVICE
- }, { /* Paules CS3, write only */
- .virtual = 0xf1000000,
- .pfn = __phys_to_pfn(0x18000000),
+ }, { /* Simpad CS3 */
+ .virtual = CS3_BASE,
+ .pfn = __phys_to_pfn(SA1100_CS3_PHYS),
.length = 0x00100000,
.type = MT_DEVICE
},
@@ -78,12 +132,12 @@ static void simpad_uart_pm(struct uart_port *port, u_int state, u_int oldstate)
if (port->mapbase == (u_int)&Ser1UTCR0) {
if (state)
{
- clear_cs3_bit(RS232_ON);
- clear_cs3_bit(DECT_POWER_ON);
+ simpad_clear_cs3_bit(RS232_ON);
+ simpad_clear_cs3_bit(DECT_POWER_ON);
}else
{
- set_cs3_bit(RS232_ON);
- set_cs3_bit(DECT_POWER_ON);
+ simpad_set_cs3_bit(RS232_ON);
+ simpad_set_cs3_bit(DECT_POWER_ON);
}
}
}
@@ -143,9 +197,10 @@ static void __init simpad_map_io(void)
iotable_init(simpad_io_desc, ARRAY_SIZE(simpad_io_desc));
- set_cs3_bit (EN1 | EN0 | LED2_ON | DISPLAY_ON | RS232_ON |
- ENABLE_5V | RESET_SIMCARD | DECT_POWER_ON);
-
+ /* Initialize CS3 */
+ cs3_shadow = (EN1 | EN0 | LED2_ON | DISPLAY_ON |
+ RS232_ON | ENABLE_5V | RESET_SIMCARD | DECT_POWER_ON);
+ __simpad_write_cs3(); /* Spinlocks not yet initialized */
sa1100_register_uart_fns(&simpad_port_fns);
sa1100_register_uart(0, 3); /* serial interface */
@@ -171,12 +226,13 @@ static void __init simpad_map_io(void)
static void simpad_power_off(void)
{
- local_irq_disable(); // was cli
- set_cs3(0x800); /* only SD_MEDIAQ */
+ local_irq_disable(); /* was cli */
+ cs3_shadow = SD_MEDIAQ;
+ __simpad_write_cs3(); /* Bypass spinlock here */
/* disable internal oscillator, float CS lines */
PCFR = (PCFR_OPDE | PCFR_FP | PCFR_FS);
- /* enable wake-up on GPIO0 (Assabet...) */
+ /* enable wake-up on GPIO0 */
PWER = GFER = GRER = 1;
/*
* set scratchpad to zero, just in case it is used as a
@@ -212,6 +268,19 @@ static int __init simpad_init(void)
{
int ret;
+ spin_lock_init(&cs3_lock);
+
+ cs3_gpio.label = "simpad_cs3";
+ cs3_gpio.base = SIMPAD_CS3_GPIO_BASE;
+ cs3_gpio.ngpio = 24;
+ cs3_gpio.set = cs3_gpio_set;
+ cs3_gpio.get = cs3_gpio_get;
+ cs3_gpio.direction_input = cs3_gpio_direction_input;
+ cs3_gpio.direction_output = cs3_gpio_direction_output;
+ ret = gpiochip_add(&cs3_gpio);
+ if (ret)
+ printk(KERN_WARNING "simpad: Unable to register cs3 GPIO device");
+
pm_power_off = simpad_power_off;
sa11x0_register_mtd(&simpad_flash_data, simpad_flash_resources,
diff --git a/drivers/pcmcia/sa1100_simpad.c b/drivers/pcmcia/sa1100_simpad.c
index c998f7a..540320d 100644
--- a/drivers/pcmcia/sa1100_simpad.c
+++ b/drivers/pcmcia/sa1100_simpad.c
@@ -15,10 +15,6 @@
#include <mach/simpad.h>
#include "sa1100_generic.h"
-extern long get_cs3_shadow(void);
-extern void set_cs3_bit(int value);
-extern void clear_cs3_bit(int value);
-
static struct pcmcia_irqs irqs[] = {
{ 1, IRQ_GPIO_CF_CD, "CF_CD" },
};
@@ -26,7 +22,7 @@ static struct pcmcia_irqs irqs[] = {
static int simpad_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
{
- clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
+ simpad_clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
skt->socket.pci_irq = IRQ_GPIO_CF_IRQ;
@@ -38,8 +34,8 @@ static void simpad_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
soc_pcmcia_free_irqs(skt, irqs, ARRAY_SIZE(irqs));
/* Disable CF bus: */
- //set_cs3_bit(PCMCIA_BUFF_DIS);
- clear_cs3_bit(PCMCIA_RESET);
+ /*simpad_set_cs3_bit(PCMCIA_BUFF_DIS);*/
+ simpad_clear_cs3_bit(PCMCIA_RESET);
}
static void
@@ -47,15 +43,15 @@ simpad_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
struct pcmcia_state *state)
{
unsigned long levels = GPLR;
- long cs3reg = get_cs3_shadow();
+ long cs3reg = simpad_get_cs3_shadow();
state->detect=((levels & GPIO_CF_CD)==0)?1:0;
state->ready=(levels & GPIO_CF_IRQ)?1:0;
state->bvd1=1; /* Not available on Simpad. */
state->bvd2=1; /* Not available on Simpad. */
state->wrprot=0; /* Not available on Simpad. */
-
- if((cs3reg & 0x0c) == 0x0c) {
+
+ if ((cs3reg & 0x0c) == 0x0c) {
state->vs_3v=0;
state->vs_Xv=0;
} else {
@@ -75,23 +71,23 @@ simpad_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
/* Murphy: see table of MIC2562a-1 */
switch (state->Vcc) {
case 0:
- clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
+ simpad_clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
break;
case 33:
- clear_cs3_bit(VCC_3V_EN|EN1);
- set_cs3_bit(VCC_5V_EN|EN0);
+ simpad_clear_cs3_bit(VCC_3V_EN|EN1);
+ simpad_set_cs3_bit(VCC_5V_EN|EN0);
break;
case 50:
- clear_cs3_bit(VCC_5V_EN|EN1);
- set_cs3_bit(VCC_3V_EN|EN0);
+ simpad_clear_cs3_bit(VCC_5V_EN|EN1);
+ simpad_set_cs3_bit(VCC_3V_EN|EN0);
break;
default:
printk(KERN_ERR "%s(): unrecognized Vcc %u\n",
__func__, state->Vcc);
- clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
+ simpad_clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
local_irq_restore(flags);
return -1;
}
@@ -110,7 +106,7 @@ static void simpad_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
static void simpad_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt)
{
soc_pcmcia_disable_irqs(skt, irqs, ARRAY_SIZE(irqs));
- set_cs3_bit(PCMCIA_RESET);
+ simpad_set_cs3_bit(PCMCIA_RESET);
}
static struct pcmcia_low_level simpad_pcmcia_ops = {
--
1.7.2.3
More information about the linux-arm-kernel
mailing list