[PATCH 6/7] msm: mahimahi: add gpio pin muxing code

[Daniel Walker]

Add in old style pin muxing code. This code is from Google's
tree. However, the other way to do this is to use gpiomux, but
it's currently not mature enough to have on/off configurations.

This code was taken from Google's tree, with slight modifications
and clean up.

Signed-off-by: Daniel Walker <dwalker at codeaurora.org>
---
 arch/arm/mach-msm/board-mahimahi-mmc.c |   32 ++++++++++++++++++++++++++++++++
 1 files changed, 32 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-msm/board-mahimahi-mmc.c b/arch/arm/mach-msm/board-mahimahi-mmc.c
index 991818e..13e45d0 100644
--- a/arch/arm/mach-msm/board-mahimahi-mmc.c
+++ b/arch/arm/mach-msm/board-mahimahi-mmc.c
@@ -54,6 +54,34 @@ static struct msm_mmc_gpio sdc1_gpio_cfg[] = {
 	{67, "sdc1_dat_0"},
 };
 
+static void config_gpio_table(uint32_t *table, int len)
+{
+	int n;
+	unsigned id;
+	for (n = 0; n < len; n++) {
+		id = table[n];
+		msm_proc_comm(PCOM_RPC_GPIO_TLMM_CONFIG_EX, &id, 0);
+	}
+}
+
+static uint32_t sdcard_on_gpio_table[] = {
+	PCOM_GPIO_CFG(62, 1, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_8MA), /* CLK */
+	PCOM_GPIO_CFG(63, 1, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_8MA), /* CMD */
+	PCOM_GPIO_CFG(64, 1, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_4MA), /* DAT3 */
+	PCOM_GPIO_CFG(65, 1, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_4MA), /* DAT2 */
+	PCOM_GPIO_CFG(66, 1, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_4MA), /* DAT1 */
+	PCOM_GPIO_CFG(67, 1, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_4MA), /* DAT0 */
+};
+
+static uint32_t sdcard_off_gpio_table[] = {
+	PCOM_GPIO_CFG(62, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* CLK */
+	PCOM_GPIO_CFG(63, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* CMD */
+	PCOM_GPIO_CFG(64, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT3 */
+	PCOM_GPIO_CFG(65, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT2 */
+	PCOM_GPIO_CFG(66, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT1 */
+	PCOM_GPIO_CFG(67, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT0 */
+};
+
 static struct vreg	*sdslot_vreg;
 static uint32_t		sdslot_vdd = 0xffffffff;
 static uint32_t		sdslot_vreg_enabled;
@@ -86,6 +114,8 @@ static uint32_t mahimahi_sdslot_switchvdd(struct device *dev, unsigned int vdd)
 	sdslot_vdd = vdd;
 
 	if (vdd == 0) {
+		config_gpio_table(sdcard_off_gpio_table,
+				  ARRAY_SIZE(sdcard_off_gpio_table));
 		vreg_disable(sdslot_vreg);
 		sdslot_vreg_enabled = 0;
 		return 0;
@@ -95,6 +125,8 @@ static uint32_t mahimahi_sdslot_switchvdd(struct device *dev, unsigned int vdd)
 		ret = vreg_enable(sdslot_vreg);
 		if (ret)
 			pr_err("Error enabling vreg (%d)\n", ret);
+		config_gpio_table(sdcard_on_gpio_table,
+				  ARRAY_SIZE(sdcard_on_gpio_table));
 		sdslot_vreg_enabled = 1;
 	}
 
-- 
1.7.0.4

-- 
Sent by a consultant of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.