[PATCH 6/7] arm: plat-omap: system.h: move voiceblue definitions into the board header
Russell King - ARM Linux
linux at arm.linux.org.uk
Tue Jan 18 04:22:03 EST 2011
On Tue, Jan 18, 2011 at 09:52:44AM +0200, Aaro Koskinen wrote:
> Move voiceblue definitions into the board-specific header.
>
> Signed-off-by: Aaro Koskinen <aaro.koskinen at iki.fi>
Let's instead simplify this, and allow other platforms to hook into the
reset handler if they choose. This has only been build-tested on my
omap1 (which includes voiceblue) and omap4 configurations.
8<------
Subject: ARM: OMAP: Allow platforms to hook reset cleanly
This adds a clean method to allow platforms to hook into the reset
code if they require to.
Signed-off-by: Russell King <rmk+kernel at arm.linux.org.uk>
---
arch/arm/mach-omap1/Makefile | 2
arch/arm/mach-omap1/board-voiceblue.c | 106 +++++++++++++++++--------------
arch/arm/mach-omap1/reset.c | 25 +++++++
arch/arm/mach-omap2/prcm.c | 5 +
arch/arm/plat-omap/include/plat/prcm.h | 1
arch/arm/plat-omap/include/plat/system.h | 38 -----------
6 files changed, 91 insertions(+), 86 deletions(-)
diff --git a/arch/arm/mach-omap1/Makefile b/arch/arm/mach-omap1/Makefile
index 6ee1950..148dc6b 100644
--- a/arch/arm/mach-omap1/Makefile
+++ b/arch/arm/mach-omap1/Makefile
@@ -4,7 +4,7 @@
# Common support
obj-y := io.o id.o sram.o irq.o mux.o flash.o serial.o devices.o dma.o
-obj-y += clock.o clock_data.o opp_data.o
+obj-y += clock.o clock_data.o opp_data.o reset.o
obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c
index 815a69c..6712817 100644
--- a/arch/arm/mach-omap1/board-voiceblue.c
+++ b/arch/arm/mach-omap1/board-voiceblue.c
@@ -26,6 +26,7 @@
#include <linux/smc91x.h>
#include <mach/hardware.h>
+#include <mach/system.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -163,52 +164,6 @@ static void __init voiceblue_init_irq(void)
omap_init_irq();
}
-static void __init voiceblue_init(void)
-{
- /* mux pins for uarts */
- omap_cfg_reg(UART1_TX);
- omap_cfg_reg(UART1_RTS);
- omap_cfg_reg(UART2_TX);
- omap_cfg_reg(UART2_RTS);
- omap_cfg_reg(UART3_TX);
- omap_cfg_reg(UART3_RX);
-
- /* Watchdog */
- gpio_request(0, "Watchdog");
- /* smc91x reset */
- gpio_request(7, "SMC91x reset");
- gpio_direction_output(7, 1);
- udelay(2); /* wait at least 100ns */
- gpio_set_value(7, 0);
- mdelay(50); /* 50ms until PHY ready */
- /* smc91x interrupt pin */
- gpio_request(8, "SMC91x irq");
- /* 16C554 reset*/
- gpio_request(6, "16C554 reset");
- gpio_direction_output(6, 0);
- /* 16C554 interrupt pins */
- gpio_request(12, "16C554 irq");
- gpio_request(13, "16C554 irq");
- gpio_request(14, "16C554 irq");
- gpio_request(15, "16C554 irq");
- set_irq_type(gpio_to_irq(12), IRQ_TYPE_EDGE_RISING);
- set_irq_type(gpio_to_irq(13), IRQ_TYPE_EDGE_RISING);
- set_irq_type(gpio_to_irq(14), IRQ_TYPE_EDGE_RISING);
- set_irq_type(gpio_to_irq(15), IRQ_TYPE_EDGE_RISING);
-
- platform_add_devices(voiceblue_devices, ARRAY_SIZE(voiceblue_devices));
- omap_board_config = voiceblue_config;
- omap_board_config_size = ARRAY_SIZE(voiceblue_config);
- omap_serial_init();
- omap1_usb_init(&voiceblue_usb_config);
- omap_register_i2c_bus(1, 100, NULL, 0);
-
- /* There is a good chance board is going up, so enable power LED
- * (it is connected through invertor) */
- omap_writeb(0x00, OMAP_LPG1_LCR);
- omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */
-}
-
static void __init voiceblue_map_io(void)
{
omap1_map_common_io();
@@ -275,8 +230,17 @@ void voiceblue_wdt_ping(void)
gpio_set_value(0, wdt_gpio_state);
}
-void voiceblue_reset(void)
+static void voiceblue_reset(char mode, const char *cmd)
{
+ /*
+ * Workaround for 5912/1611b bug mentioned in sprz209d.pdf p. 28
+ * "Global Software Reset Affects Traffic Controller Frequency".
+ */
+ if (cpu_is_omap5912()) {
+ omap_writew(omap_readw(DPLL_CTL) & ~(1 << 4), DPLL_CTL);
+ omap_writew(0x8, ARM_RSTCT1);
+ }
+
set_bit(MACHINE_REBOOT, &machine_state);
voiceblue_wdt_enable();
while (1) ;
@@ -286,6 +250,54 @@ EXPORT_SYMBOL(voiceblue_wdt_enable);
EXPORT_SYMBOL(voiceblue_wdt_disable);
EXPORT_SYMBOL(voiceblue_wdt_ping);
+static void __init voiceblue_init(void)
+{
+ /* mux pins for uarts */
+ omap_cfg_reg(UART1_TX);
+ omap_cfg_reg(UART1_RTS);
+ omap_cfg_reg(UART2_TX);
+ omap_cfg_reg(UART2_RTS);
+ omap_cfg_reg(UART3_TX);
+ omap_cfg_reg(UART3_RX);
+
+ /* Watchdog */
+ gpio_request(0, "Watchdog");
+ /* smc91x reset */
+ gpio_request(7, "SMC91x reset");
+ gpio_direction_output(7, 1);
+ udelay(2); /* wait at least 100ns */
+ gpio_set_value(7, 0);
+ mdelay(50); /* 50ms until PHY ready */
+ /* smc91x interrupt pin */
+ gpio_request(8, "SMC91x irq");
+ /* 16C554 reset*/
+ gpio_request(6, "16C554 reset");
+ gpio_direction_output(6, 0);
+ /* 16C554 interrupt pins */
+ gpio_request(12, "16C554 irq");
+ gpio_request(13, "16C554 irq");
+ gpio_request(14, "16C554 irq");
+ gpio_request(15, "16C554 irq");
+ set_irq_type(gpio_to_irq(12), IRQ_TYPE_EDGE_RISING);
+ set_irq_type(gpio_to_irq(13), IRQ_TYPE_EDGE_RISING);
+ set_irq_type(gpio_to_irq(14), IRQ_TYPE_EDGE_RISING);
+ set_irq_type(gpio_to_irq(15), IRQ_TYPE_EDGE_RISING);
+
+ platform_add_devices(voiceblue_devices, ARRAY_SIZE(voiceblue_devices));
+ omap_board_config = voiceblue_config;
+ omap_board_config_size = ARRAY_SIZE(voiceblue_config);
+ omap_serial_init();
+ omap1_usb_init(&voiceblue_usb_config);
+ omap_register_i2c_bus(1, 100, NULL, 0);
+
+ /* There is a good chance board is going up, so enable power LED
+ * (it is connected through invertor) */
+ omap_writeb(0x00, OMAP_LPG1_LCR);
+ omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */
+
+ arch_reset = voiceblue_reset;
+}
+
MACHINE_START(VOICEBLUE, "VoiceBlue OMAP5910")
/* Maintainer: Ladislav Michl <michl at 2n.cz> */
.boot_params = 0x10000100,
diff --git a/arch/arm/mach-omap1/reset.c b/arch/arm/mach-omap1/reset.c
index e69de29..ad951ee 100644
--- a/arch/arm/mach-omap1/reset.c
+++ b/arch/arm/mach-omap1/reset.c
@@ -0,0 +1,25 @@
+/*
+ * OMAP1 reset support
+ */
+#include <linux/kernel.h>
+#include <linux/io.h>
+
+#include <mach/hardware.h>
+#include <mach/system.h>
+#include <plat/prcm.h>
+
+void omap1_arch_reset(char mode, const char *cmd)
+{
+ /*
+ * Workaround for 5912/1611b bug mentioned in sprz209d.pdf p. 28
+ * "Global Software Reset Affects Traffic Controller Frequency".
+ */
+ if (cpu_is_omap5912()) {
+ omap_writew(omap_readw(DPLL_CTL) & ~(1 << 4), DPLL_CTL);
+ omap_writew(0x8, ARM_RSTCT1);
+ }
+
+ omap_writew(1, ARM_RSTCT1);
+}
+
+void (*arch_reset)(char, const char *) = omap1_arch_reset;
diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c
index 679bcd2..6be1438 100644
--- a/arch/arm/mach-omap2/prcm.c
+++ b/arch/arm/mach-omap2/prcm.c
@@ -24,6 +24,7 @@
#include <linux/io.h>
#include <linux/delay.h>
+#include <mach/system.h>
#include <plat/common.h>
#include <plat/prcm.h>
#include <plat/irqs.h>
@@ -57,7 +58,7 @@ u32 omap_prcm_get_reset_sources(void)
EXPORT_SYMBOL(omap_prcm_get_reset_sources);
/* Resets clock rates and reboots the system. Only called from system.h */
-void omap_prcm_arch_reset(char mode, const char *cmd)
+static void omap_prcm_arch_reset(char mode, const char *cmd)
{
s16 prcm_offs = 0;
@@ -108,6 +109,8 @@ void omap_prcm_arch_reset(char mode, const char *cmd)
omap2_prm_read_mod_reg(prcm_offs, OMAP2_RM_RSTCTRL); /* OCP barrier */
}
+void (*arch_reset)(char, const char *) = omap_prcm_arch_reset;
+
/**
* omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness
* @reg: physical address of module IDLEST register
diff --git a/arch/arm/plat-omap/include/plat/prcm.h b/arch/arm/plat-omap/include/plat/prcm.h
index 2fdf8c8..267f43b 100644
--- a/arch/arm/plat-omap/include/plat/prcm.h
+++ b/arch/arm/plat-omap/include/plat/prcm.h
@@ -28,7 +28,6 @@
#define __ASM_ARM_ARCH_OMAP_PRCM_H
u32 omap_prcm_get_reset_sources(void);
-void omap_prcm_arch_reset(char mode, const char *cmd);
int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest,
const char *name);
diff --git a/arch/arm/plat-omap/include/plat/system.h b/arch/arm/plat-omap/include/plat/system.h
index d0a119f..c5fa9e9 100644
--- a/arch/arm/plat-omap/include/plat/system.h
+++ b/arch/arm/plat-omap/include/plat/system.h
@@ -4,48 +4,14 @@
*/
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <linux/clk.h>
-#include <asm/mach-types.h>
-#include <mach/hardware.h>
-
-#include <plat/prcm.h>
-
-#ifndef CONFIG_MACH_VOICEBLUE
-#define voiceblue_reset() do {} while (0)
-#else
-extern void voiceblue_reset(void);
-#endif
+#include <asm/proc-fns.h>
static inline void arch_idle(void)
{
cpu_do_idle();
}
-static inline void omap1_arch_reset(char mode, const char *cmd)
-{
- /*
- * Workaround for 5912/1611b bug mentioned in sprz209d.pdf p. 28
- * "Global Software Reset Affects Traffic Controller Frequency".
- */
- if (cpu_is_omap5912()) {
- omap_writew(omap_readw(DPLL_CTL) & ~(1 << 4),
- DPLL_CTL);
- omap_writew(0x8, ARM_RSTCT1);
- }
-
- if (machine_is_voiceblue())
- voiceblue_reset();
- else
- omap_writew(1, ARM_RSTCT1);
-}
-
-static inline void arch_reset(char mode, const char *cmd)
-{
- if (!cpu_class_is_omap2())
- omap1_arch_reset(mode, cmd);
- else
- omap_prcm_arch_reset(mode, cmd);
-}
+extern void (*arch_reset)(char, const char *);
#endif
More information about the linux-arm-kernel
mailing list