[PATCH] MTD: atmel_nand: Add DMA support to access Nandflash
Ryan Mallon
ryan at bluewatersys.com
Mon Jan 17 22:08:19 EST 2011
On 01/18/2011 03:56 PM, Hong Xu wrote:
> Some SAM9 chips have the ability to perform DMA between CPU and SMC controller.
> This patch adds DMA support for SAM9RL, SAM9G45, SSAM9G46,AM9M10, SAM9M11.
>
> Signed-off-by: Hong Xu <hong.xu at atmel.com>
Couple more notes below. I think the normal exit path for
atmel_nand_dma_op needs to call dma_unmap_single. The other suggestions
below are just stylistic.
Also, you still need a change to Kconfig to add the dependency on the
AT_HDMAC driver otherwise users without that option selected will get
build errors.
~Ryan
> ---
> drivers/mtd/nand/atmel_nand.c | 166 ++++++++++++++++++++++++++++++++++++++--
> 1 files changed, 157 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c
> index ccce0f0..02ad055 100644
> --- a/drivers/mtd/nand/atmel_nand.c
> +++ b/drivers/mtd/nand/atmel_nand.c
> @@ -48,6 +48,9 @@
> #define no_ecc 0
> #endif
>
> +static int use_dma = 1;
> +module_param(use_dma, int, 0);
> +
> static int on_flash_bbt = 0;
> module_param(on_flash_bbt, int, 0);
>
> @@ -89,11 +92,20 @@ struct atmel_nand_host {
> struct nand_chip nand_chip;
> struct mtd_info mtd;
> void __iomem *io_base;
> + dma_addr_t io_phys;
> struct atmel_nand_data *board;
> struct device *dev;
> void __iomem *ecc;
> +
> + struct completion comp;
> + struct dma_chan *dma_chan;
Nitpick, tab delimit these two fields to line up with everything else.
> };
>
> +static int cpu_has_dma(void)
> +{
> + return cpu_is_at91sam9rl() || cpu_is_at91sam9g45();
> +}
> +
> /*
> * Enable NAND.
> */
> @@ -150,7 +162,7 @@ static int atmel_nand_device_ready(struct mtd_info *mtd)
> /*
> * Minimal-overhead PIO for data access.
> */
> -static void atmel_read_buf(struct mtd_info *mtd, u8 *buf, int len)
> +static void atmel_read_buf8(struct mtd_info *mtd, u8 *buf, int len)
> {
> struct nand_chip *nand_chip = mtd->priv;
>
> @@ -164,7 +176,7 @@ static void atmel_read_buf16(struct mtd_info *mtd, u8 *buf, int len)
> __raw_readsw(nand_chip->IO_ADDR_R, buf, len / 2);
> }
>
> -static void atmel_write_buf(struct mtd_info *mtd, const u8 *buf, int len)
> +static void atmel_write_buf8(struct mtd_info *mtd, const u8 *buf, int len)
> {
> struct nand_chip *nand_chip = mtd->priv;
>
> @@ -178,6 +190,121 @@ static void atmel_write_buf16(struct mtd_info *mtd, const u8 *buf, int len)
> __raw_writesw(nand_chip->IO_ADDR_W, buf, len / 2);
> }
>
> +static void dma_complete_func(void *completion)
> +{
> + complete(completion);
> +}
> +
> +static int atmel_nand_dma_op(struct mtd_info *mtd, void *buf, int len,
> + int is_read)
> +{
> + struct dma_device *dma_dev;
> + enum dma_ctrl_flags flags;
> + dma_addr_t dma_src_addr, dma_dst_addr, phys_addr;
> + struct dma_async_tx_descriptor *tx = NULL;
> + dma_cookie_t cookie;
> + struct nand_chip *chip = mtd->priv;
> + struct atmel_nand_host *host = chip->priv;
> + void *p = buf;
> + enum dma_data_direction dir = is_read? DMA_FROM_DEVICE : DMA_TO_DEVICE;
> +
> + if (buf >= high_memory) {
> + struct page *pg;
> +
> + if (((size_t)buf & PAGE_MASK) !=
> + ((size_t)(buf + len - 1) & PAGE_MASK)) {
> + dev_warn(host->dev, "Buffer doesn't fit in one page:");
> + goto err_dma;
> + }
> +
> + pg = vmalloc_to_page(buf);
> + if (pg == 0) {
> + dev_err(host->dev, "Failed to vmalloc_to_page:");
> + goto err_dma;
> + }
> + p = page_address(pg) + ((size_t)buf & ~PAGE_MASK);
> + }
> +
> + dma_dev = host->dma_chan->device;
> +
> + flags = DMA_CTRL_ACK | DMA_COMPL_SKIP_DEST_UNMAP | DMA_PREP_INTERRUPT |
> + DMA_COMPL_SKIP_SRC_UNMAP;
> +
> + phys_addr = dma_map_single(dma_dev->dev, p, len, dir);
> +
Nitpick, no blank line between function and error check.
> + if (dma_mapping_error(dma_dev->dev, phys_addr)) {
> + dev_err(host->dev, "Failed to dma_map_single:");
> + goto err_dma;
> + }
> +
> + if (is_read) {
> + dma_src_addr = host->io_phys;
> + dma_dst_addr = phys_addr;
> + } else {
> + dma_src_addr = phys_addr;
> + dma_dst_addr = host->io_phys;
> + }
> +
> + tx = dma_dev->device_prep_dma_memcpy(host->dma_chan, dma_dst_addr,
> + dma_src_addr, len, flags);
> + if (!tx) {
> + dev_err(host->dev, "Failed to prepare DMA memcpy\n");
> + goto err;
> + }
> +
> + init_completion(&host->comp);
> + tx->callback = dma_complete_func;
> + tx->callback_param = &host->comp;
> +
> + cookie = tx->tx_submit(tx);
> + if (dma_submit_error(cookie)) {
> + dev_err(host->dev, "Failed to do DMA tx_submit\n");
> + goto err;
> + }
> +
> + dma_async_issue_pending(host->dma_chan);
> +
> + wait_for_completion(&host->comp);
Is dma_unmap_single required here?
> + return 0;
> +
> +err:
> + dma_unmap_single(dma_dev->dev, phys_addr, len, dir);
> +err_dma:
> + dev_warn(host->dev, " Fall back to CPU I/O\n");
I'm not sure this will give the output you want, since you are calling
dev_err with no newline, followed by dev_warn, will it print something
like this:
"Failed to dma_map_single:<4> Fall back to CPU I/O"
Or does printk handle this auto-magically now? I do recall reading
something about printk's behaviour changing in this regard.
> + return -EIO;
> +}
> +
> +static void atmel_read_buf(struct mtd_info *mtd, u8 *buf, int len)
> +{
> + struct nand_chip *chip = mtd->priv;
> + struct atmel_nand_host *host = chip->priv;
> +
> + if (use_dma && len >= mtd->oobsize)
> + if (atmel_nand_dma_op(mtd, buf, len, 1) == 0)
> + return;
> +
> + if (host->board->bus_width_16)
> + atmel_read_buf16(mtd, buf, len);
> + else
> + atmel_read_buf8(mtd, buf, len);
> +}
> +
> +static void atmel_write_buf(struct mtd_info *mtd, const u8 *buf, int len)
> +{
> + struct nand_chip *chip = mtd->priv;
> + struct atmel_nand_host *host = chip->priv;
> +
> + if (use_dma && len >= mtd->oobsize)
> + if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) == 0)
> + return;
> +
> + if (host->board->bus_width_16)
> + atmel_write_buf16(mtd, buf, len);
> + else
> + atmel_write_buf8(mtd, buf, len);
> +}
> +
> /*
> * Calculate HW ECC
> *
> @@ -398,6 +525,8 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
> return -ENOMEM;
> }
>
> + host->io_phys = (dma_addr_t)mem->start;
> +
> host->io_base = ioremap(mem->start, mem->end - mem->start + 1);
> if (host->io_base == NULL) {
> printk(KERN_ERR "atmel_nand: ioremap failed\n");
> @@ -448,14 +577,11 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
>
> nand_chip->chip_delay = 20; /* 20us command delay time */
>
> - if (host->board->bus_width_16) { /* 16-bit bus width */
> + if (host->board->bus_width_16) /* 16-bit bus width */
> nand_chip->options |= NAND_BUSWIDTH_16;
> - nand_chip->read_buf = atmel_read_buf16;
> - nand_chip->write_buf = atmel_write_buf16;
> - } else {
> - nand_chip->read_buf = atmel_read_buf;
> - nand_chip->write_buf = atmel_write_buf;
> - }
> +
> + nand_chip->read_buf = atmel_read_buf;
> + nand_chip->write_buf = atmel_write_buf;
>
> platform_set_drvdata(pdev, host);
> atmel_nand_enable(host);
> @@ -473,6 +599,22 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
> nand_chip->options |= NAND_USE_FLASH_BBT;
> }
>
> + if (cpu_has_dma() && use_dma) {
> + dma_cap_mask_t mask;
> +
> + dma_cap_zero(mask);
> + dma_cap_set(DMA_MEMCPY, mask);
> + host->dma_chan = dma_request_channel(mask, 0, NULL);
> + if (!host->dma_chan) {
> + dev_err(host->dev, "Failed to request DMA channel\n");
> + use_dma = 0;
> + }
> + }
> + if (use_dma)
> + dev_info(host->dev, "Using DMA for NAND access.\n");
> + else
> + dev_info(host->dev, "No DMA support for NAND access.\n");
> +
> /* first scan to find the device and get the page size */
> if (nand_scan_ident(mtd, 1, NULL)) {
> res = -ENXIO;
> @@ -555,6 +697,8 @@ err_scan_ident:
> err_no_card:
> atmel_nand_disable(host);
> platform_set_drvdata(pdev, NULL);
> + if (host->dma_chan)
> + dma_release_channel(host->dma_chan);
> if (host->ecc)
> iounmap(host->ecc);
> err_ecc_ioremap:
> @@ -578,6 +722,10 @@ static int __exit atmel_nand_remove(struct platform_device *pdev)
>
> if (host->ecc)
> iounmap(host->ecc);
> +
> + if (host->dma_chan)
> + dma_release_channel(host->dma_chan);
> +
> iounmap(host->io_base);
> kfree(host);
>
--
Bluewater Systems Ltd - ARM Technology Solution Centre
Ryan Mallon 5 Amuri Park, 404 Barbadoes St
ryan at bluewatersys.com PO Box 13 889, Christchurch 8013
http://www.bluewatersys.com New Zealand
Phone: +64 3 3779127 Freecall: Australia 1800 148 751
Fax: +64 3 3779135 USA 1800 261 2934
More information about the linux-arm-kernel
mailing list