[PATCH v3 05/10] net/fec: add dual fec support for mx28
Shawn Guo
shawn.guo at freescale.com
Wed Jan 5 09:07:32 EST 2011
This patch is to add mx28 dual fec support. Here are some key notes
for mx28 fec controller.
- The mx28 fec controller naming ENET-MAC is a different IP from FEC
used on other i.mx variants. But they are basically compatible
on software interface, so it's possible to share the same driver.
- ENET-MAC design made an improper assumption that it runs on a
big-endian system. As the result, driver has to swap every frame
going to and coming from the controller.
- The external phys can only be configured by fec0, which means fec1
can not work independently and both phys need to be configured by
mii_bus attached on fec0.
- ENET-MAC reset will get mac address registers reset too.
- ENET-MAC MII/RMII mode and 10M/100M speed are configured
differently FEC.
- ETHER_EN bit must be set to get ENET-MAC interrupt work.
Signed-off-by: Shawn Guo <shawn.guo at freescale.com>
---
Changes for v3:
- Move v2 changes into patch #3
- Use device name to check if it's running on ENET-MAC
drivers/net/Kconfig | 7 ++-
drivers/net/fec.c | 140 +++++++++++++++++++++++++++++++++++++++++++++------
drivers/net/fec.h | 5 +-
3 files changed, 131 insertions(+), 21 deletions(-)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 4f1755b..f34629b 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1944,18 +1944,19 @@ config 68360_ENET
config FEC
bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
- MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5
+ MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5 || SOC_IMX28
select PHYLIB
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire and Freescale i.MX processors.
config FEC2
- bool "Second FEC ethernet controller (on some ColdFire CPUs)"
+ bool "Second FEC ethernet controller"
depends on FEC
help
Say Y here if you want to use the second built-in 10/100 Fast
- ethernet controller on some Motorola ColdFire processors.
+ ethernet controller on some Motorola ColdFire and Freescale
+ i.MX processors.
config FEC_MPC52xx
tristate "MPC52xx FEC driver"
diff --git a/drivers/net/fec.c b/drivers/net/fec.c
index 8a1c51f..67ba263 100644
--- a/drivers/net/fec.c
+++ b/drivers/net/fec.c
@@ -17,6 +17,8 @@
*
* Bug fixes and cleanup by Philippe De Muyter (phdm at macqel.be)
* Copyright (c) 2004-2006 Macq Electronique SA.
+ *
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
*/
#include <linux/module.h>
@@ -45,20 +47,33 @@
#include <asm/cacheflush.h>
-#ifndef CONFIG_ARCH_MXC
+#if !defined(CONFIG_ARCH_MXC) && !defined(CONFIG_SOC_IMX28)
#include <asm/coldfire.h>
#include <asm/mcfsim.h>
#endif
#include "fec.h"
-#ifdef CONFIG_ARCH_MXC
-#include <mach/hardware.h>
+#if defined(CONFIG_ARCH_MXC) || defined(CONFIG_SOC_IMX28)
#define FEC_ALIGNMENT 0xf
#else
#define FEC_ALIGNMENT 0x3
#endif
+#define DRIVER_NAME "fec"
+#define ENET_MAC_NAME "enet-mac"
+
+static struct platform_device_id fec_devtype[] = {
+ {
+ .name = DRIVER_NAME,
+ }, {
+ .name = ENET_MAC_NAME,
+ }
+};
+
+static unsigned fec_is_enetmac;
+static struct mii_bus *fec_mii_bus;
+
static unsigned char macaddr[ETH_ALEN];
module_param_array(macaddr, byte, NULL, 0);
MODULE_PARM_DESC(macaddr, "FEC Ethernet MAC address");
@@ -129,7 +144,8 @@ MODULE_PARM_DESC(macaddr, "FEC Ethernet MAC address");
* account when setting it.
*/
#if defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x) || \
- defined(CONFIG_M520x) || defined(CONFIG_M532x) || defined(CONFIG_ARCH_MXC)
+ defined(CONFIG_M520x) || defined(CONFIG_M532x) || \
+ defined(CONFIG_ARCH_MXC) || defined(CONFIG_SOC_IMX28)
#define OPT_FRAME_SIZE (PKT_MAXBUF_SIZE << 16)
#else
#define OPT_FRAME_SIZE 0
@@ -208,6 +224,17 @@ static void fec_stop(struct net_device *dev);
/* Transmitter timeout */
#define TX_TIMEOUT (2 * HZ)
+static void *swap_buffer(void *bufaddr, int len)
+{
+ int i;
+ unsigned int *buf = bufaddr;
+
+ for (i = 0; i < (len + 3) / 4; i++, buf++)
+ *buf = __swab32(*buf);
+
+ return bufaddr;
+}
+
static netdev_tx_t
fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
@@ -256,6 +283,14 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev)
bufaddr = fep->tx_bounce[index];
}
+ /*
+ * enet-mac design made an improper assumption that it's running
+ * on a big endian system. As the result, driver has to swap
+ * every frame going to and coming from the controller.
+ */
+ if (fec_is_enetmac)
+ swap_buffer(bufaddr, skb->len);
+
/* Save skb pointer */
fep->tx_skbuff[fep->skb_cur] = skb;
@@ -487,6 +522,9 @@ fec_enet_rx(struct net_device *dev)
dma_unmap_single(NULL, bdp->cbd_bufaddr, bdp->cbd_datlen,
DMA_FROM_DEVICE);
+ if (fec_is_enetmac)
+ swap_buffer(data, pkt_len);
+
/* This does 16 byte alignment, exactly what we need.
* The packet length includes FCS, but we don't want to
* include that when passing upstream as it messes up
@@ -689,6 +727,7 @@ static int fec_enet_mii_probe(struct net_device *dev)
char mdio_bus_id[MII_BUS_ID_SIZE];
char phy_name[MII_BUS_ID_SIZE + 3];
int phy_id;
+ int dev_id = fep->pdev->id;
fep->phy_dev = NULL;
@@ -700,6 +739,8 @@ static int fec_enet_mii_probe(struct net_device *dev)
continue;
if (fep->mii_bus->phy_map[phy_id]->phy_id == 0)
continue;
+ if (fec_is_enetmac && dev_id--)
+ continue;
strncpy(mdio_bus_id, fep->mii_bus->id, MII_BUS_ID_SIZE);
break;
}
@@ -741,6 +782,28 @@ static int fec_enet_mii_init(struct platform_device *pdev)
struct fec_enet_private *fep = netdev_priv(dev);
int err = -ENXIO, i;
+ /*
+ * The dual fec interfaces are not equivalent with enet-mac.
+ * Here are the differences:
+ *
+ * - fec0 supports MII & RMII modes while fec1 only supports RMII
+ * - fec0 acts as the 1588 time master while fec1 is slave
+ * - external phys can only be configured by fec0
+ *
+ * That is to say fec1 can not work independently. It only works
+ * when fec0 is working. The reason behind this design is that the
+ * second interface is added primarily for Switch mode.
+ *
+ * Because of the last point above, both phys are attached on fec0
+ * mdio interface in board design, and need to be configured by
+ * fec0 mii_bus.
+ */
+ if (fec_is_enetmac && pdev->id) {
+ /* fec1 uses fec0 mii_bus */
+ fep->mii_bus = fec_mii_bus;
+ return 0;
+ }
+
fep->mii_timeout = 0;
/*
@@ -777,6 +840,10 @@ static int fec_enet_mii_init(struct platform_device *pdev)
if (mdiobus_register(fep->mii_bus))
goto err_out_free_mdio_irq;
+ /* save fec0 mii_bus */
+ if (fec_is_enetmac)
+ fec_mii_bus = fep->mii_bus;
+
return 0;
err_out_free_mdio_irq:
@@ -1149,11 +1216,22 @@ fec_restart(struct net_device *dev, int duplex)
{
struct fec_enet_private *fep = netdev_priv(dev);
int i;
+ u32 val, temp_mac[2];
/* Whack a reset. We should wait for this. */
writel(1, fep->hwp + FEC_ECNTRL);
udelay(10);
+ /*
+ * enet-mac reset will reset mac address registers too,
+ * so need to reconfigure it.
+ */
+ if (fec_is_enetmac) {
+ memcpy(&temp_mac, dev->dev_addr, ETH_ALEN);
+ writel(cpu_to_be32(temp_mac[0]), fep->hwp + FEC_ADDR_LOW);
+ writel(cpu_to_be32(temp_mac[1]), fep->hwp + FEC_ADDR_HIGH);
+ }
+
/* Clear any outstanding interrupt. */
writel(0xffc00000, fep->hwp + FEC_IEVENT);
@@ -1200,20 +1278,45 @@ fec_restart(struct net_device *dev, int duplex)
/* Set MII speed */
writel(fep->phy_speed, fep->hwp + FEC_MII_SPEED);
-#ifdef FEC_MIIGSK_ENR
- if (fep->phy_interface == PHY_INTERFACE_MODE_RMII) {
- /* disable the gasket and wait */
- writel(0, fep->hwp + FEC_MIIGSK_ENR);
- while (readl(fep->hwp + FEC_MIIGSK_ENR) & 4)
- udelay(1);
+ /*
+ * The phy interface and speed need to get configured
+ * differently on enet-mac.
+ */
+ if (fec_is_enetmac) {
+ val = readl(fep->hwp + FEC_R_CNTRL);
- /* configure the gasket: RMII, 50 MHz, no loopback, no echo */
- writel(1, fep->hwp + FEC_MIIGSK_CFGR);
+ /* MII or RMII */
+ if (fep->phy_interface == PHY_INTERFACE_MODE_RMII)
+ val |= (1 << 8);
+ else
+ val &= ~(1 << 8);
- /* re-enable the gasket */
- writel(2, fep->hwp + FEC_MIIGSK_ENR);
- }
+ /* 10M or 100M */
+ if (fep->phy_dev && fep->phy_dev->speed == SPEED_100)
+ val &= ~(1 << 9);
+ else
+ val |= (1 << 9);
+
+ writel(val, fep->hwp + FEC_R_CNTRL);
+ } else {
+#ifdef FEC_MIIGSK_ENR
+ if (fep->phy_interface == PHY_INTERFACE_MODE_RMII) {
+ /* disable the gasket and wait */
+ writel(0, fep->hwp + FEC_MIIGSK_ENR);
+ while (readl(fep->hwp + FEC_MIIGSK_ENR) & 4)
+ udelay(1);
+
+ /*
+ * configure the gasket:
+ * RMII, 50 MHz, no loopback, no echo
+ */
+ writel(1, fep->hwp + FEC_MIIGSK_CFGR);
+
+ /* re-enable the gasket */
+ writel(2, fep->hwp + FEC_MIIGSK_ENR);
+ }
#endif
+ }
/* And last, enable the transmit and receive processing */
writel(2, fep->hwp + FEC_ECNTRL);
@@ -1301,6 +1404,10 @@ fec_probe(struct platform_device *pdev)
}
}
+ /* check if it's ENET-MAC controller via device name */
+ if (!strcmp(pdev->name, ENET_MAC_NAME))
+ fec_is_enetmac = 1;
+
fep->clk = clk_get(&pdev->dev, "fec_clk");
if (IS_ERR(fep->clk)) {
ret = PTR_ERR(fep->clk);
@@ -1410,12 +1517,13 @@ static const struct dev_pm_ops fec_pm_ops = {
static struct platform_driver fec_driver = {
.driver = {
- .name = "fec",
+ .name = DRIVER_NAME,
.owner = THIS_MODULE,
#ifdef CONFIG_PM
.pm = &fec_pm_ops,
#endif
},
+ .id_table = fec_devtype,
.probe = fec_probe,
.remove = __devexit_p(fec_drv_remove),
};
diff --git a/drivers/net/fec.h b/drivers/net/fec.h
index 2c48b25..ace318d 100644
--- a/drivers/net/fec.h
+++ b/drivers/net/fec.h
@@ -14,7 +14,8 @@
/****************************************************************************/
#if defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x) || \
- defined(CONFIG_M520x) || defined(CONFIG_M532x) || defined(CONFIG_ARCH_MXC)
+ defined(CONFIG_M520x) || defined(CONFIG_M532x) || \
+ defined(CONFIG_ARCH_MXC) || defined(CONFIG_SOC_IMX28)
/*
* Just figures, Motorola would have to change the offsets for
* registers in the same peripheral device on different models
@@ -78,7 +79,7 @@
/*
* Define the buffer descriptor structure.
*/
-#ifdef CONFIG_ARCH_MXC
+#if defined(CONFIG_ARCH_MXC) || defined(CONFIG_SOC_IMX28)
struct bufdesc {
unsigned short cbd_datlen; /* Data length */
unsigned short cbd_sc; /* Control and status info */
--
1.7.1
More information about the linux-arm-kernel
mailing list