[PATCH 2/2] s5pc110: add MIPI-DSI controller driver.
Inki Dae
inki.dae at samsung.com
Wed Jan 5 05:35:52 EST 2011
S5PC110 and S5PC210 SoC platform have one or two MIPI-DSI controller.
MIPI-DSI controller can be used to connect MIPI-DSI based LCD Panel.
this patch adds MIPI-DSI controller driver.
to use this driver, MIPI-DSI based LCD panel driver have to register
mipi_dsim_lcd_driver object to MIPI-DSI driver and then when MIPI-DSI
driver is probed, probe callback of LCD panel driver registered would
be called.
Signed-off-by: Inki Dae <inki.dae at samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
---
arch/arm/plat-s5p/include/plat/dsim.h | 357 ++++++++++++++++
arch/arm/plat-s5p/include/plat/regs-dsim.h | 141 ++++++
drivers/video/Kconfig | 7 +
drivers/video/Makefile | 2 +
drivers/video/s5p_mipi_dsi.c | 428 +++++++++++++++++++
drivers/video/s5p_mipi_dsi_common.c | 635 ++++++++++++++++++++++++++++
drivers/video/s5p_mipi_dsi_common.h | 38 ++
drivers/video/s5p_mipi_dsi_lowlevel.c | 553 ++++++++++++++++++++++++
drivers/video/s5p_mipi_dsi_lowlevel.h | 98 +++++
9 files changed, 2259 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/plat-s5p/include/plat/dsim.h
create mode 100644 arch/arm/plat-s5p/include/plat/regs-dsim.h
create mode 100644 drivers/video/s5p_mipi_dsi.c
create mode 100644 drivers/video/s5p_mipi_dsi_common.c
create mode 100644 drivers/video/s5p_mipi_dsi_common.h
create mode 100644 drivers/video/s5p_mipi_dsi_lowlevel.c
create mode 100644 drivers/video/s5p_mipi_dsi_lowlevel.h
diff --git a/arch/arm/plat-s5p/include/plat/dsim.h b/arch/arm/plat-s5p/include/plat/dsim.h
new file mode 100644
index 0000000..9aa5a93
--- /dev/null
+++ b/arch/arm/plat-s5p/include/plat/dsim.h
@@ -0,0 +1,357 @@
+/* linux/arm/arch/plat-s5p/include/plat/dsim.h
+ *
+ * Platform data header for Samsung SoC MIPI-DSIM.
+ *
+ * Copyright (c) 2009 Samsung Electronics
+ * InKi Dae <inki.dae at samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef _DSIM_H
+#define _DSIM_H
+
+#include <linux/device.h>
+#include <linux/fb.h>
+
+#define PANEL_NAME_SIZE (32)
+
+enum mipi_dsim_interface_type {
+ DSIM_COMMAND,
+ DSIM_VIDEO
+};
+
+enum mipi_dsim_virtual_ch_no {
+ DSIM_VIRTUAL_CH_0,
+ DSIM_VIRTUAL_CH_1,
+ DSIM_VIRTUAL_CH_2,
+ DSIM_VIRTUAL_CH_3
+};
+
+enum mipi_dsim_burst_mode_type {
+ DSIM_NON_BURST_SYNC_EVENT,
+ DSIM_NON_BURST_SYNC_PULSE = 2,
+ DSIM_BURST,
+ DSIM_NON_VIDEO_MODE
+};
+
+enum mipi_dsim_no_of_data_lane {
+ DSIM_DATA_LANE_1,
+ DSIM_DATA_LANE_2,
+ DSIM_DATA_LANE_3,
+ DSIM_DATA_LANE_4
+};
+
+enum mipi_dsim_byte_clk_src {
+ DSIM_PLL_OUT_DIV8,
+ DSIM_EXT_CLK_DIV8,
+ DSIM_EXT_CLK_BYPASS
+};
+
+enum mipi_dsim_pixel_format {
+ DSIM_CMD_3BPP,
+ DSIM_CMD_8BPP,
+ DSIM_CMD_12BPP,
+ DSIM_CMD_16BPP,
+ DSIM_VID_16BPP_565,
+ DSIM_VID_18BPP_666PACKED,
+ DSIM_18BPP_666LOOSELYPACKED,
+ DSIM_24BPP_888
+};
+
+/**
+ * struct mipi_dsim_config - interface for configuring mipi-dsi controller.
+ *
+ * @auto_flush: enable or disable Auto flush of MD FIFO using VSYNC pulse.
+ * @eot_disable: enable or disable EoT packet in HS mode.
+ * @auto_vertical_cnt: specifies auto vertical count mode.
+ * in Video mode, the vertical line transition uses line counter
+ * configured by VSA, VBP, and Vertical resolution.
+ * If this bit is set to '1', the line counter does not use VSA and VBP
+ * registers.(in command mode, this variable is ignored)
+ * @hse: set horizontal sync event mode.
+ * In VSYNC pulse and Vporch area, MIPI DSI master transfers only HSYNC
+ * start packet to MIPI DSI slave at MIPI DSI spec1.1r02.
+ * this bit transfers HSYNC end packet in VSYNC pulse and Vporch area
+ * (in mommand mode, this variable is ignored)
+ * @hfp: specifies HFP disable mode.
+ * if this variable is set, DSI master ignores HFP area in VIDEO mode.
+ * (in command mode, this variable is ignored)
+ * @hbp: specifies HBP disable mode.
+ * if this variable is set, DSI master ignores HBP area in VIDEO mode.
+ * (in command mode, this variable is ignored)
+ * @hsa: specifies HSA disable mode.
+ * if this variable is set, DSI master ignores HSA area in VIDEO mode.
+ * (in command mode, this variable is ignored)
+ * @e_interface: specifies interface to be used.(CPU or RGB interface)
+ * @e_virtual_ch: specifies virtual channel number that main or
+ * sub diaplsy uses.
+ * @e_pixel_format: specifies pixel stream format for main or sub display.
+ * @e_burst_mode: selects Burst mode in Video mode.
+ * in Non-burst mode, RGB data area is filled with RGB data and NULL
+ * packets, according to input bandwidth of RGB interface.
+ * In Burst mode, RGB data area is filled with RGB data only.
+ * @e_no_data_lane: specifies data lane count to be used by Master.
+ * @e_byte_clk: select byte clock source. (it must be DSIM_PLL_OUT_DIV8)
+ * DSIM_EXT_CLK_DIV8 and DSIM_EXT_CLK_BYPASSS are not supported.
+ * @pll_stable_time: specifies the PLL Timer for stability of the ganerated
+ * clock(System clock cycle base)
+ * if the timer value goes to 0x00000000, the clock stable bit of status
+ * and interrupt register is set.
+ * @esc_clk: specifies escape clock frequency for getting the escape clock
+ * prescaler value.
+ * @stop_holding_cnt: specifies the interval value between transmitting
+ * read packet(or write "set_tear_on" command) and BTA request.
+ * after transmitting read packet or write "set_tear_on" command,
+ * BTA requests to D-PHY automatically. this counter value specifies
+ * the interval between them.
+ * @bta_timeout: specifies the timer for BTA.
+ * this register specifies time out from BTA request to change
+ * the direction with respect to Tx escape clock.
+ * @rx_timeout: specifies the timer for LP Rx mode timeout.
+ * this register specifies time out on how long RxValid deasserts,
+ * after RxLpdt asserts with respect to Tx escape clock.
+ * - RxValid specifies Rx data valid indicator.
+ * - RxLpdt specifies an indicator that D-PHY is under RxLpdt mode.
+ * - RxValid and RxLpdt specifies signal from D-PHY.
+ * @lcd_panel_info: pointer for lcd panel specific structure.
+ * this structure specifies width, height, timing and polarity and so on.
+ * @mipi_ddi_pd: pointer to lcd panel platform data.
+ */
+struct mipi_dsim_config {
+ unsigned char auto_flush;
+ unsigned char eot_disable;
+
+ unsigned char auto_vertical_cnt;
+ unsigned char hse;
+ unsigned char hfp;
+ unsigned char hbp;
+ unsigned char hsa;
+
+ enum mipi_dsim_interface_type e_interface;
+ enum mipi_dsim_virtual_ch_no e_virtual_ch;
+ enum mipi_dsim_pixel_format e_pixel_format;
+ enum mipi_dsim_burst_mode_type e_burst_mode;
+ enum mipi_dsim_no_of_data_lane e_no_data_lane;
+ enum mipi_dsim_byte_clk_src e_byte_clk;
+
+ /*
+ * ===========================================
+ * | P | M | S | MHz |
+ * -------------------------------------------
+ * | 3 | 100 | 3 | 100 |
+ * | 3 | 100 | 2 | 200 |
+ * | 3 | 63 | 1 | 252 |
+ * | 4 | 100 | 1 | 300 |
+ * | 4 | 110 | 1 | 330 |
+ * | 12 | 350 | 1 | 350 |
+ * | 3 | 100 | 1 | 400 |
+ * | 4 | 150 | 1 | 450 |
+ * | 3 | 118 | 1 | 472 |
+ * | 12 | 250 | 0 | 500 |
+ * | 4 | 100 | 0 | 600 |
+ * | 3 | 81 | 0 | 648 |
+ * | 3 | 88 | 0 | 704 |
+ * | 3 | 90 | 0 | 720 |
+ * | 3 | 100 | 0 | 800 |
+ * | 12 | 425 | 0 | 850 |
+ * | 4 | 150 | 0 | 900 |
+ * | 12 | 475 | 0 | 950 |
+ * | 6 | 250 | 0 | 1000 |
+ * -------------------------------------------
+ */
+ unsigned char p;
+ unsigned short m;
+ unsigned char s;
+
+ unsigned int pll_stable_time;
+ unsigned long esc_clk;
+
+ unsigned short stop_holding_cnt;
+ unsigned char bta_timeout;
+ unsigned short rx_timeout;
+
+ void *lcd_panel_info;
+ void *dsim_ddi_pd;
+};
+
+/**
+ * struct mipi_dsim_device - global interface for mipi-dsi driver.
+ *
+ * @dev: driver model representation of the device.
+ * @clock: pointer to MIPI-DSI clock of clock framework.
+ * @irq: interrupt number to MIPI-DSI controller.
+ * @reg_base: base address to memory mapped SRF of MIPI-DSI controller.
+ * (virtual address)
+ * @pd: pointer to MIPI-DSI driver platform data.
+ * @dsim_info: infomation for configuring mipi-dsi controller.
+ * @master_ops: callbacks to mipi-dsi operations.
+ * @lcd_info: pointer to mipi_lcd_info structure.
+ * @state: specifies status of MIPI-DSI controller.
+ * the status could be RESET, INIT, STOP, HSCLKEN and ULPS.
+ * @resume_complete: indicates whether resume operation is completed or not.
+ * @data_lane: specifiec enabled data lane number.
+ * this variable would be set by driver according to e_no_data_lane
+ * automatically.
+ * @e_clk_src: select byte clock source.
+ * this variable would be set by driver according to e_byte_clock
+ * automatically.
+ * @hs_clk: HS clock rate.
+ * this variable would be set by driver automatically.
+ * @byte_clk: Byte clock rate.
+ * this variable would be set by driver automatically.
+ * @escape_clk: ESCAPE clock rate.
+ * this variable would be set by driver automatically.
+ * @freq_band: indicates Bitclk frequency band for D-PHY global timing.
+ * Serial Clock(=ByteClk X 8) FreqBand[3:0]
+ * ~ 99.99 MHz 0000
+ * 100 ~ 119.99 MHz 0001
+ * 120 ~ 159.99 MHz 0010
+ * 160 ~ 199.99 MHz 0011
+ * 200 ~ 239.99 MHz 0100
+ * 140 ~ 319.99 MHz 0101
+ * 320 ~ 389.99 MHz 0110
+ * 390 ~ 449.99 MHz 0111
+ * 450 ~ 509.99 MHz 1000
+ * 510 ~ 559.99 MHz 1001
+ * 560 ~ 639.99 MHz 1010
+ * 640 ~ 689.99 MHz 1011
+ * 690 ~ 769.99 MHz 1100
+ * 770 ~ 869.99 MHz 1101
+ * 870 ~ 949.99 MHz 1110
+ * 950 ~ 1000 MHz 1111
+ * this variable would be calculated by driver automatically.
+ */
+struct mipi_dsim_device {
+ struct device *dev;
+ struct resource *res;
+ struct clk *clock;
+ unsigned int irq;
+ void __iomem *reg_base;
+
+ struct s5p_platform_mipi_dsim *pd;
+ struct mipi_dsim_config *dsim_config;
+ struct mipi_dsim_master_ops *master_ops;
+ struct mipi_dsim_ddi *dsim_ddi;
+
+ unsigned int state;
+ unsigned int resume_complete;
+ unsigned int data_lane;
+ enum mipi_dsim_byte_clk_src e_clk_src;
+ unsigned long hs_clk;
+ unsigned long byte_clk;
+ unsigned long escape_clk;
+ unsigned char freq_band;
+};
+
+/**
+ * struct s5p_platform_mipi_dsim - interface to platform data
+ * for mipi-dsi driver.
+ *
+ * @lcd_panel_name: specifies lcd panel name registered to mipi-dsi driver.
+ * lcd panel driver searched would be actived.
+ * @dsim_config: pointer of structure for configuring mipi-dsi controller.
+ * @dsim_lcd_info: pointer to structure for configuring
+ * mipi-dsi based lcd panel.
+ * @mipi_power: callback pointer for enabling or disabling mipi power.
+ * @part_reset: callback pointer for reseting mipi phy.
+ * @init_d_phy: callback pointer for enabing d_phy of dsi master.
+ * @get_fb_frame_done: callback pointer for getting frame done status of the
+ * display controller(FIMD).
+ * @trigger: callback pointer for triggering display controller(FIMD)
+ * in case of CPU mode.
+ * @delay_for_stabilization: specifies stable time.
+ * this delay needs when writing data on SFR
+ * after mipi mode became LP mode.
+ */
+struct s5p_platform_mipi_dsim {
+ char lcd_panel_name[PANEL_NAME_SIZE];
+
+ struct mipi_dsim_config *dsim_config;
+ struct mipi_dsim_lcd_config *dsim_lcd_config;
+
+ unsigned int delay_for_stabilization;
+
+ int (*mipi_power) (struct mipi_dsim_device *dsim, unsigned int enable);
+ int (*part_reset) (struct mipi_dsim_device *dsim);
+ int (*init_d_phy) (struct mipi_dsim_device *dsim);
+ int (*get_fb_frame_done) (struct fb_info *info);
+ void (*trigger) (struct fb_info *info);
+};
+/**
+ * struct mipi_dsim_master_ops - callbacks to mipi-dsi operations.
+ *
+ * @cmd_write: transfer command to lcd panel at LP mode.
+ * @cmd_read: read command from rx register.
+ * @get_dsim_frame_done: get the status that all screen data have been
+ * transferred to mipi-dsi.
+ * @clear_dsim_frame_done: clear frame done status.
+ * @change_dsim_transfer_mode: change transfer mode to LP or HS mode.
+ * - LP mode is used when commands data ard transferred to lcd panel.
+ * @get_fb_frame_done: get frame done status of display controller.
+ * @trigger: trigger display controller.
+ * - this one would be used only in case of CPU mode.
+ */
+
+struct mipi_dsim_master_ops {
+ int (*cmd_write) (struct mipi_dsim_device *dsim, unsigned int data_id,
+ unsigned int data0, unsigned int data1);
+ int (*cmd_read) (struct mipi_dsim_device *dsim, unsigned int data_id,
+ unsigned int data0, unsigned int data1);
+ int (*get_dsim_frame_done) (struct mipi_dsim_device *dsim);
+ int (*clear_dsim_frame_done) (struct mipi_dsim_device *dsim);
+
+ int (*change_dsim_transfer_mode) (struct mipi_dsim_device *dsim,
+ unsigned int mode);
+
+ int (*get_fb_frame_done) (struct fb_info *info);
+ void (*trigger) (struct fb_info *info);
+};
+
+/**
+ * device structure for mipi-dsi based lcd panel.
+ *
+ * @dev: driver model representation of the device.
+ * @id: id of device registered and when device is registered
+ * id would be counted.
+ * @modalias: name of the driver to use with this device, or an
+ * alias for that name.
+ * @mipi_lcd_drv: pointer of mipi_lcd_driver.
+ * @master: pointer to dsim_device.
+ */
+struct mipi_dsim_lcd_device {
+ struct device dev;
+ int id;
+ char modalias[64];
+
+ struct mipi_dsim_lcd_driver *dsim_drv;
+ struct mipi_dsim_device *master;
+};
+
+/**
+ * driver structure for mipi-dsi based lcd panel.
+ *
+ * this structure should be registered by lcd panel driver.
+ * mipi-dsi driver seeks lcd panel registered through name field
+ * and calls these callback functions in appropriate time.
+ */
+struct mipi_dsim_lcd_driver {
+ char *name;
+
+ int (*probe)(struct mipi_dsim_lcd_device *dsim_dev);
+ int (*remove)(struct mipi_dsim_lcd_device *dsim_dev);
+ void (*shutdown)(struct mipi_dsim_lcd_device *dsim_dev);
+ int (*suspend)(struct mipi_dsim_lcd_device *dsim_dev);
+ int (*resume)(struct mipi_dsim_lcd_device *dsim_dev);
+};
+
+/**
+ * register mipi_dsim_lcd_driver object defined by lcd panel driver
+ * to mipi-dsi driver.
+ */
+extern int s5p_mipi_dsi_register_lcd_driver(struct mipi_dsim_lcd_driver
+ *lcd_drv);
+
+#endif /* _DSIM_H */
diff --git a/arch/arm/plat-s5p/include/plat/regs-dsim.h b/arch/arm/plat-s5p/include/plat/regs-dsim.h
new file mode 100644
index 0000000..7ef5a2f
--- /dev/null
+++ b/arch/arm/plat-s5p/include/plat/regs-dsim.h
@@ -0,0 +1,141 @@
+/* linux/arch/arm/plat-s5p/include/plat/regs-dsim.h
+ *
+ * Register definition file for Samsung MIPI-DSIM driver
+ *
+ * InKi Dae <inki.dae at samsung.com>, Copyright (c) 2009 Samsung Electronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef _REGS_DSIM_H
+#define _REGS_DSIM_H
+
+#define S5P_DSIM_STATUS (0x0) /* Status register */
+#define S5P_DSIM_SWRST (0x4) /* Software reset register */
+#define S5P_DSIM_CLKCTRL (0x8) /* Clock control register */
+#define S5P_DSIM_TIMEOUT (0xc) /* Time out register */
+#define S5P_DSIM_CONFIG (0x10) /* Configuration register */
+#define S5P_DSIM_ESCMODE (0x14) /* Escape mode register */
+
+/* Main display image resolution register */
+#define S5P_DSIM_MDRESOL (0x18)
+#define S5P_DSIM_MVPORCH (0x1c) /* Main display Vporch register */
+#define S5P_DSIM_MHPORCH (0x20) /* Main display Hporch register */
+#define S5P_DSIM_MSYNC (0x24) /* Main display sync area register */
+
+/* Sub display image resolution register */
+#define S5P_DSIM_SDRESOL (0x28)
+#define S5P_DSIM_INTSRC (0x2c) /* Interrupt source register */
+#define S5P_DSIM_INTMSK (0x30) /* Interrupt mask register */
+#define S5P_DSIM_PKTHDR (0x34) /* Packet Header FIFO register */
+#define S5P_DSIM_PAYLOAD (0x38) /* Payload FIFO register */
+#define S5P_DSIM_RXFIFO (0x3c) /* Read FIFO register */
+#define S5P_DSIM_FIFOTHLD (0x40) /* FIFO threshold level register */
+#define S5P_DSIM_FIFOCTRL (0x44) /* FIFO status and control register */
+
+/* FIFO memory AC characteristic register */
+#define S5P_DSIM_PLLCTRL (0x4c) /* PLL control register */
+#define S5P_DSIM_PLLTMR (0x50) /* PLL timer register */
+#define S5P_DSIM_PHYACCHR (0x54) /* D-PHY AC characteristic register */
+#define S5P_DSIM_PHYACCHR1 (0x58) /* D-PHY AC characteristic register1 */
+
+/* DSIM_STATUS */
+#define DSIM_STOP_STATE_DAT(x) (((x) & 0xf) << 0)
+#define DSIM_STOP_STATE_CLK (1 << 8)
+#define DSIM_TX_READY_HS_CLK (1 << 10)
+
+/* DSIM_SWRST */
+#define DSIM_FUNCRST (1 << 16)
+#define DSIM_SWRST (1 << 0)
+
+/* S5P_DSIM_TIMEOUT */
+#define DSIM_LPDR_TOUT_SHIFT (0)
+#define DSIM_BTA_TOUT_SHIFT (16)
+
+/* S5P_DSIM_CLKCTRL */
+#define DSIM_LANE_ESC_CLKEN_SHIFT (19)
+#define DSIM_BYTE_CLKEN_SHIFT (24)
+#define DSIM_BYTE_CLK_SRC_SHIFT (25)
+#define DSIM_PLL_BYPASS_SHIFT (27)
+#define DSIM_ESC_CLKEN_SHIFT (28)
+#define DSIM_TX_REQUEST_HSCLK_SHIFT (31)
+#define DSIM_LANE_ESC_CLKEN(x) (((x) & 0x1f) << \
+ DSIM_LANE_ESC_CLKEN_SHIFT)
+#define DSIM_BYTE_CLK_ENABLE (1 << DSIM_BYTE_CLKEN_SHIFT)
+#define DSIM_BYTE_CLK_DISABLE (0 << DSIM_BYTE_CLKEN_SHIFT)
+#define DSIM_PLL_BYPASS_EXTERNAL (1 << DSIM_PLL_BYPASS_SHIFT)
+#define DSIM_ESC_CLKEN_ENABLE (1 << DSIM_ESC_CLKEN_SHIFT)
+#define DSIM_ESC_CLKEN_DISABLE (0 << DSIM_ESC_CLKEN_SHIFT)
+
+/* S5P_DSIM_CONFIG */
+#define DSIM_NUM_OF_DATALANE_SHIFT (5)
+#define DSIM_HSA_MODE_SHIFT (20)
+#define DSIM_HBP_MODE_SHIFT (21)
+#define DSIM_HFP_MODE_SHIFT (22)
+#define DSIM_HSE_MODE_SHIFT (23)
+#define DSIM_AUTO_MODE_SHIFT (24)
+#define DSIM_LANE_ENx(x) (((x) & 0x1f) << 0)
+
+#define DSIM_NUM_OF_DATA_LANE(x) ((x) << DSIM_NUM_OF_DATALANE_SHIFT)
+
+/* S5P_DSIM_ESCMODE */
+#define DSIM_TX_LPDT_SHIFT (6)
+#define DSIM_CMD_LPDT_SHIFT (7)
+#define DSIM_TX_LPDT_LP (1 << DSIM_TX_LPDT_SHIFT)
+#define DSIM_CMD_LPDT_LP (1 << DSIM_CMD_LPDT_SHIFT)
+#define DSIM_STOP_STATE_CNT_SHIFT (21)
+#define DSIM_FORCE_STOP_STATE_SHIFT (20)
+
+/* S5P_DSIM_MDRESOL */
+#define DSIM_MAIN_STAND_BY (1 << 31)
+#define DSIM_MAIN_VRESOL(x) (((x) & 0x7ff) << 16)
+#define DSIM_MAIN_HRESOL(x) (((x) & 0X7ff) << 0)
+
+/* S5P_DSIM_MVPORCH */
+#define DSIM_CMD_ALLOW_SHIFT (28)
+#define DSIM_STABLE_VFP_SHIFT (16)
+#define DSIM_MAIN_VBP_SHIFT (0)
+#define DSIM_CMD_ALLOW_MASK (0xf << DSIM_CMD_ALLOW_SHIFT)
+#define DSIM_STABLE_VFP_MASK (0x7ff << DSIM_STABLE_VFP_SHIFT)
+#define DSIM_MAIN_VBP_MASK (0x7ff << DSIM_MAIN_VBP_SHIFT)
+
+/* S5P_DSIM_MHPORCH */
+#define DSIM_MAIN_HFP_SHIFT (16)
+#define DSIM_MAIN_HBP_SHIFT (0)
+#define DSIM_MAIN_HFP_MASK ((0xffff) << DSIM_MAIN_HFP_SHIFT)
+#define DSIM_MAIN_HBP_MASK ((0xffff) << DSIM_MAIN_HBP_SHIFT)
+
+/* S5P_DSIM_MSYNC */
+#define DSIM_MAIN_VSA_SHIFT (22)
+#define DSIM_MAIN_HSA_SHIFT (0)
+#define DSIM_MAIN_VSA_MASK ((0x3ff) << DSIM_MAIN_VSA_SHIFT)
+#define DSIM_MAIN_HSA_MASK ((0xffff) << DSIM_MAIN_HSA_SHIFT)
+
+/* S5P_DSIM_SDRESOL */
+#define DSIM_SUB_STANDY_SHIFT (31)
+#define DSIM_SUB_VRESOL_SHIFT (16)
+#define DSIM_SUB_HRESOL_SHIFT (0)
+#define DSIM_SUB_STANDY_MASK ((0x1) << DSIM_SUB_STANDY_SHIFT)
+#define DSIM_SUB_VRESOL_MASK ((0x7ff) << DSIM_SUB_VRESOL_SHIFT)
+#define DSIM_SUB_HRESOL_MASK ((0x7ff) << DSIM_SUB_HRESOL_SHIFT)
+
+/* S5P_DSIM_INTSRC */
+#define INTSRC_FRAME_DONE (1 << 24)
+#define INTSRC_PLL_STABLE (1 << 31)
+
+/* S5P_DSIM_INTMSK */
+#define INTMSK_FRAME_DONE (1 << 24)
+
+/* S5P_DSIM_FIFOCTRL */
+#define SFR_HEADER_EMPTY (1 << 22)
+
+/* S5P_DSIM_PHYACCHR */
+#define DSIM_AFC_CTL(x) (((x) & 0x7) << 5)
+
+/* S5P_DSIM_PLLCTRL */
+#define DSIM_PLL_EN_SHIFT (23)
+#define DSIM_FREQ_BAND_SHIFT (24)
+
+#endif /* _REGS_DSIM_H */
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 932e7bb..9744e32 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -2098,6 +2098,13 @@ config FB_S3C2410_DEBUG
Turn on debugging messages. Note that you can set/unset at run time
through sysfs
+config S5P_MIPI_DSI
+ tristate "Samsung SoC MIPI-DSI support."
+ depends on FB_S3C && ARCH_S5PV210
+ default n
+ ---help---
+ This enables support for MIPI-DSI device.
+
config FB_NUC900
bool "NUC900 LCD framebuffer support"
depends on FB && ARCH_W90X900
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 36aca21..12052a2 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -119,6 +119,8 @@ obj-$(CONFIG_FB_SH7760) += sh7760fb.o
obj-$(CONFIG_FB_IMX) += imxfb.o
obj-$(CONFIG_FB_S3C) += s3c-fb.o
obj-$(CONFIG_FB_S3C2410) += s3c2410fb.o
+obj-$(CONFIG_S5P_MIPI_DSI) += s5p_mipi_dsi.o s5p_mipi_dsi_common.o \
+ s5p_mipi_dsi_lowlevel.o
obj-$(CONFIG_FB_FSL_DIU) += fsl-diu-fb.o
obj-$(CONFIG_FB_COBALT) += cobalt_lcdfb.o
obj-$(CONFIG_FB_PNX4008_DUM) += pnx4008/
diff --git a/drivers/video/s5p_mipi_dsi.c b/drivers/video/s5p_mipi_dsi.c
new file mode 100644
index 0000000..0bd9a44
--- /dev/null
+++ b/drivers/video/s5p_mipi_dsi.c
@@ -0,0 +1,428 @@
+/* linux/drivers/video/s5p_mipi_dsi.c
+ *
+ * Samsung SoC MIPI-DSIM driver.
+ *
+ * InKi Dae, <inki.dae at samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/clk.h>
+#include <linux/mutex.h>
+#include <linux/wait.h>
+#include <linux/fs.h>
+#include <linux/mm.h>
+#include <linux/fb.h>
+#include <linux/ctype.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/memory.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/kthread.h>
+#include <linux/regulator/consumer.h>
+#include <linux/notifier.h>
+
+#include <plat/fb.h>
+#include <plat/regs-dsim.h>
+#include <plat/dsim.h>
+
+#include <mach/map.h>
+
+#include "s5p_mipi_dsi_common.h"
+
+#define master_to_driver(a) (a->dsim_ddi->dsim_lcd_drv)
+#define master_to_device(a) (a->dsim_ddi->dsim_lcd_dev)
+#define set_master_to_device(a) (a->dsim_ddi->dsim_lcd_dev->master = a)
+
+struct mipi_dsim_ddi {
+ struct list_head list;
+ struct mipi_dsim_lcd_driver *dsim_lcd_drv;
+ struct mipi_dsim_lcd_device *dsim_lcd_dev;
+};
+
+static LIST_HEAD(dsim_ddi_list);
+static DEFINE_MUTEX(mipi_lock);
+
+static struct s5p_platform_mipi_dsim *to_dsim_plat(struct platform_device *pdev)
+{
+ return (struct s5p_platform_mipi_dsim *)pdev->dev.platform_data;
+}
+
+static irqreturn_t s5p_mipi_dsi_interrupt_handler(int irq, void *dev_id)
+{
+ return IRQ_HANDLED;
+}
+
+int s5p_mipi_dsi_register_lcd_driver(struct mipi_dsim_lcd_driver *lcd_drv)
+{
+ struct mipi_dsim_ddi *dsim_ddi;
+ struct mipi_dsim_lcd_device *dsim_lcd_dev;
+ static unsigned int id;
+ int ret;
+
+ dsim_ddi = kzalloc(sizeof(struct mipi_dsim_ddi), GFP_KERNEL);
+ if (!dsim_ddi) {
+ printk(KERN_ERR "failed to allocate dsim_ddi object.\n");
+ return -EFAULT;
+ }
+
+ dsim_ddi->dsim_lcd_drv = lcd_drv;
+
+ dsim_lcd_dev = kzalloc(sizeof(struct mipi_dsim_lcd_device), GFP_KERNEL);
+ if (!dsim_lcd_dev) {
+ printk(KERN_ERR "failed to allocate dsim_lcd_dev object.\n");
+ ret = -EFAULT;
+ goto err_dsim;
+ }
+
+ mutex_lock(&mipi_lock);
+
+ dsim_lcd_dev->id = id++;
+ dsim_ddi->dsim_lcd_dev = dsim_lcd_dev;
+
+ device_initialize(&dsim_lcd_dev->dev);
+
+ strcpy(dsim_lcd_dev->modalias, lcd_drv->name);
+
+ dev_set_name(&dsim_lcd_dev->dev, "mipi-dsi.%d\n", dsim_lcd_dev->id);
+
+ ret = device_add(&dsim_lcd_dev->dev);
+ if (ret < 0) {
+ printk(KERN_ERR "can't %s %s, status %d\n",
+ "add", dev_name(&dsim_lcd_dev->dev), ret);
+ id--;
+ goto err_device_add;
+ }
+
+ list_add_tail(&dsim_ddi->list, &dsim_ddi_list);
+
+ mutex_unlock(&mipi_lock);
+
+ printk(KERN_DEBUG "registered panel driver(%s) to mipi-dsi driver.\n",
+ lcd_drv->name);
+
+ return ret;
+
+err_device_add:
+ kfree(dsim_lcd_dev);
+
+err_dsim:
+ kfree(dsim_ddi);
+
+ return ret;
+}
+
+/*
+ * This function is a wrapper for changing transfer mode.
+ * It is used for the panel driver before and after changing gamma value.
+ */
+static int s5p_mipi_dsi_change_transfer_mode(struct mipi_dsim_device *dsim,
+ unsigned int mode)
+{
+ if (mode < 0 || mode > 1) {
+ dev_err(dsim->dev, "mode range should be 0 or 1.\n");
+ return -EINVAL;
+ }
+
+ s5p_mipi_dsi_set_data_transfer_mode(dsim, mode);
+
+ return 0;
+}
+
+static struct mipi_dsim_ddi *find_mipi_client_registered
+ (struct mipi_dsim_device *dsim, const char *name)
+{
+ struct mipi_dsim_ddi *dsim_ddi;
+ struct mipi_dsim_lcd_driver *dsim_lcd_drv = NULL;
+
+ mutex_lock(&mipi_lock);
+
+ dev_dbg(dsim->dev, "find lcd panel driver(%s).\n",
+ name);
+
+ list_for_each_entry(dsim_ddi, &dsim_ddi_list, list) {
+ dsim_lcd_drv = dsim_ddi->dsim_lcd_drv;
+
+ if ((strcmp(dsim_lcd_drv->name, name)) == 0) {
+ mutex_unlock(&mipi_lock);
+ dev_dbg(dsim->dev, "found!!!(%s).\n",
+ dsim_lcd_drv->name);
+ return dsim_ddi;
+ }
+ }
+
+ dev_warn(dsim->dev, "failed to find lcd panel driver(%s).\n",
+ name);
+
+ mutex_unlock(&mipi_lock);
+
+ return NULL;
+}
+
+/* define MIPI-DSI Master operations. */
+static struct mipi_dsim_master_ops master_ops = {
+ .cmd_write = s5p_mipi_dsi_wr_data,
+ .get_dsim_frame_done = s5p_mipi_dsi_get_frame_done_status,
+ .clear_dsim_frame_done = s5p_mipi_dsi_clear_frame_done,
+ .change_dsim_transfer_mode = s5p_mipi_dsi_change_transfer_mode,
+};
+
+static int s5p_mipi_dsi_probe(struct platform_device *pdev)
+{
+ struct resource *res;
+ struct mipi_dsim_device *dsim;
+ struct mipi_dsim_config *dsim_config;
+ struct s5p_platform_mipi_dsim *dsim_pd;
+ int ret = -1;
+
+ dsim = kzalloc(sizeof(struct mipi_dsim_device), GFP_KERNEL);
+ if (!dsim) {
+ dev_err(&pdev->dev, "failed to allocate dsim object.\n");
+ return -EFAULT;
+ }
+
+ dsim->pd = to_dsim_plat(pdev);
+ dsim->dev = &pdev->dev;
+ dsim->resume_complete = 0;
+
+ /* get s5p_platform_mipi_dsim. */
+ dsim_pd = (struct s5p_platform_mipi_dsim *)dsim->pd;
+ /* get mipi_dsim_config. */
+ dsim_config = dsim_pd->dsim_config;
+ dsim->dsim_config = dsim_config;
+ dsim->master_ops = &master_ops;
+
+ dsim->clock = clk_get(&pdev->dev, "dsim");
+ if (IS_ERR(dsim->clock)) {
+ dev_err(&pdev->dev, "failed to get dsim clock source\n");
+ goto err_clock_get;
+ }
+
+ clk_enable(dsim->clock);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "failed to get io memory region\n");
+ ret = -EINVAL;
+ goto err_platform_get;
+ }
+
+ res = request_mem_region(res->start, resource_size(res),
+ dev_name(&pdev->dev));
+ if (!res) {
+ dev_err(&pdev->dev, "failed to request io memory region\n");
+ ret = -EINVAL;
+ goto err_mem_region;
+ }
+
+ dsim->res = res;
+
+ dsim->reg_base = ioremap(res->start, resource_size(res));
+ if (!dsim->reg_base) {
+ dev_err(&pdev->dev, "failed to remap io region\n");
+ ret = -EINVAL;
+ goto err_mem_region;
+ }
+
+ /*
+ * it uses frame done interrupt handler
+ * only in case of MIPI Video mode.
+ */
+ if (dsim_config->e_interface == DSIM_VIDEO) {
+ dsim->irq = platform_get_irq(pdev, 0);
+ if (request_irq(dsim->irq, s5p_mipi_dsi_interrupt_handler,
+ IRQF_DISABLED, "mipi-dsi", dsim)) {
+ dev_err(&pdev->dev, "request_irq failed.\n");
+ goto err_trigger_irq;
+ }
+ }
+
+ if (dsim->pd->mipi_power)
+ dsim->pd->mipi_power(dsim, 1);
+ else {
+ dev_err(&pdev->dev, "mipi_power is NULL.\n");
+ goto err_mipi_power;
+ }
+
+ /* find lcd panel driver registered to mipi-dsi driver. */
+ dsim->dsim_ddi = find_mipi_client_registered(dsim,
+ dsim_pd->lcd_panel_name);
+ if (dsim->dsim_config == NULL) {
+ dev_err(&pdev->dev, "dsim_config is NULL.\n");
+ goto err_dsim_config;
+ }
+
+ /* set dsim to master of mipi_dsim_lcd_device. */
+ set_master_to_device(dsim);
+
+ s5p_mipi_dsi_init_dsim(dsim);
+ s5p_mipi_dsi_init_link(dsim);
+
+ s5p_mipi_dsi_set_hs_enable(dsim);
+ /* set cpu command transfer mode to hs. */
+ s5p_mipi_dsi_set_data_transfer_mode(dsim, 0);
+
+ /* initialize mipi-dsi client(lcd panel). */
+ if (master_to_driver(dsim) && (master_to_driver(dsim))->probe)
+ (master_to_driver(dsim))->probe(master_to_device(dsim));
+
+ /* it needs delay for stabilization */
+ mdelay(dsim->pd->delay_for_stabilization);
+
+ s5p_mipi_dsi_set_display_mode(dsim, dsim->dsim_config);
+
+ /* set lcdc data transfer mode to hs. */
+ s5p_mipi_dsi_set_data_transfer_mode(dsim, 1);
+
+ /* in case of command mode, trigger. */
+ if (dsim->dsim_config->e_interface == DSIM_COMMAND) {
+ if (dsim_pd->trigger)
+ dsim_pd->trigger(registered_fb[0]);
+ else
+ dev_warn(&pdev->dev, "trigger is null.\n");
+ }
+
+ platform_set_drvdata(pdev, dsim);
+
+ dev_info(&pdev->dev, "mipi-dsi driver(%s mode) has been probed.\n",
+ (dsim_config->e_interface == DSIM_COMMAND) ?
+ "CPU" : "RGB");
+
+ return 0;
+
+err_dsim_config:
+ dsim->pd->mipi_power(dsim, 0);
+
+err_mipi_power:
+err_trigger_irq:
+ release_resource(dsim->res);
+ kfree(dsim->res);
+
+ iounmap((void __iomem *) dsim->reg_base);
+
+err_mem_region:
+err_platform_get:
+ clk_disable(dsim->clock);
+ clk_put(dsim->clock);
+
+err_clock_get:
+ kfree(dsim);
+
+ return ret;
+
+}
+
+static int __devexit s5p_mipi_dsi_remove(struct platform_device *pdev)
+{
+ struct mipi_dsim_device *dsim = platform_get_drvdata(pdev);
+ struct mipi_dsim_ddi *dsim_ddi = NULL;
+
+ if (dsim->dsim_config->e_interface == DSIM_VIDEO)
+ free_irq(dsim->irq, dsim);
+
+ iounmap(dsim->reg_base);
+
+ clk_disable(dsim->clock);
+ clk_put(dsim->clock);
+
+ release_resource(dsim->res);
+ kfree(dsim->res);
+
+ list_for_each_entry(dsim_ddi, &dsim_ddi_list, list)
+ kfree(dsim_ddi);
+
+ kfree(dsim);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int s5p_mipi_dsi_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ struct mipi_dsim_device *dsim = platform_get_drvdata(pdev);
+
+ dsim->resume_complete = 0;
+
+ if (master_to_driver(dsim) && (master_to_driver(dsim))->suspend)
+ (master_to_driver(dsim))->suspend(master_to_device(dsim));
+
+ clk_disable(dsim->clock);
+
+ if (dsim->pd->mipi_power)
+ dsim->pd->mipi_power(dsim, 0);
+
+ return 0;
+}
+
+static int s5p_mipi_dsi_resume(struct platform_device *pdev)
+{
+ struct mipi_dsim_device *dsim = platform_get_drvdata(pdev);
+
+ if (dsim->pd->mipi_power)
+ dsim->pd->mipi_power(dsim, 1);
+
+ clk_enable(dsim->clock);
+
+ s5p_mipi_dsi_init_dsim(dsim);
+ s5p_mipi_dsi_init_link(dsim);
+
+ s5p_mipi_dsi_set_hs_enable(dsim);
+ /* set cpu command transfer mode to hs. */
+ s5p_mipi_dsi_set_data_transfer_mode(dsim, 0);
+
+ /* it needs delay for stabilization */
+ mdelay(dsim->pd->delay_for_stabilization);
+
+ if (master_to_driver(dsim) && (master_to_driver(dsim))->resume)
+ (master_to_driver(dsim))->resume(master_to_device(dsim));
+
+ s5p_mipi_dsi_set_display_mode(dsim, dsim->dsim_config);
+
+ /* set lcdc data transfer mode to hs. */
+ s5p_mipi_dsi_set_data_transfer_mode(dsim, 1);
+
+ dsim->resume_complete = 1;
+
+ return 0;
+}
+#else
+#define s5p_mipi_dsi_suspend NULL
+#define s5p_mipi_dsi_resume NULL
+#endif
+
+static struct platform_driver s5p_mipi_dsi_driver = {
+ .probe = s5p_mipi_dsi_probe,
+ .remove = __devexit_p(s5p_mipi_dsi_remove),
+ .suspend = s5p_mipi_dsi_suspend,
+ .resume = s5p_mipi_dsi_resume,
+ .driver = {
+ .name = "s5p-mipi-dsim",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int s5p_mipi_dsi_register(void)
+{
+ platform_driver_register(&s5p_mipi_dsi_driver);
+
+ return 0;
+}
+
+static void s5p_mipi_dsi_unregister(void)
+{
+ platform_driver_unregister(&s5p_mipi_dsi_driver);
+}
+
+module_init(s5p_mipi_dsi_register);
+module_exit(s5p_mipi_dsi_unregister);
+
+MODULE_AUTHOR("InKi Dae <inki.dae at samsung.com>");
+MODULE_DESCRIPTION("Samusung MIPI-DSI driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/video/s5p_mipi_dsi_common.c b/drivers/video/s5p_mipi_dsi_common.c
new file mode 100644
index 0000000..cb5c280
--- /dev/null
+++ b/drivers/video/s5p_mipi_dsi_common.c
@@ -0,0 +1,635 @@
+/* linux/drivers/video/s5p_mipi_dsi_common.c
+ *
+ * Samsung MIPI-DSI common driver.
+ *
+ * InKi Dae, <inki.dae at samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/mutex.h>
+#include <linux/wait.h>
+#include <linux/fs.h>
+#include <linux/mm.h>
+#include <linux/fb.h>
+#include <linux/ctype.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/memory.h>
+#include <linux/delay.h>
+#include <linux/kthread.h>
+
+#include <video/mipi_display.h>
+
+#include <plat/fb.h>
+#include <plat/regs-dsim.h>
+
+#include <mach/map.h>
+#include <plat/dsim.h>
+#include <plat/regs-dsim.h>
+
+#include "s5p_mipi_dsi_lowlevel.h"
+
+#define MHZ (1000 * 1000)
+#define FIN_HZ (24 * MHZ)
+
+#define DFIN_PLL_MIN_HZ (6 * MHZ)
+#define DFIN_PLL_MAX_HZ (12 * MHZ)
+
+#define DFVCO_MIN_HZ (500 * MHZ)
+#define DFVCO_MAX_HZ (1000 * MHZ)
+
+#define TRY_GET_FIFO_TIMEOUT (5000 * 2)
+
+#define DSIM_ESCCLK_ON (0x0)
+#define DSIM_ESCCLK_OFF (0x1)
+
+/* MIPI-DSIM status types. */
+enum {
+ DSIM_STATE_INIT, /* should be initialized. */
+ DSIM_STATE_STOP, /* CPU and LCDC are LP mode. */
+ DSIM_STATE_HSCLKEN, /* HS clock was enabled. */
+ DSIM_STATE_ULPS
+};
+
+/* define DSI lane types. */
+enum {
+ DSIM_LANE_CLOCK = (1 << 0),
+ DSIM_LANE_DATA0 = (1 << 1),
+ DSIM_LANE_DATA1 = (1 << 2),
+ DSIM_LANE_DATA2 = (1 << 3),
+ DSIM_LANE_DATA3 = (1 << 4)
+};
+
+static unsigned int dpll_table[15] = {
+ 100, 120, 170, 220, 270,
+ 320, 390, 450, 510, 560,
+ 640, 690, 770, 870, 950 };
+
+static void s5p_mipi_dsi_long_data_wr(struct mipi_dsim_device *dsim,
+ unsigned int data0, unsigned int data1)
+{
+ unsigned int data_cnt = 0, payload = 0;
+
+ /* in case that data count is more then 4 */
+ for (data_cnt = 0; data_cnt < data1; data_cnt += 4) {
+ /*
+ * after sending 4bytes per one time,
+ * send remainder data less then 4.
+ */
+ if ((data1 - data_cnt) < 4) {
+ if ((data1 - data_cnt) == 3) {
+ payload = *(u8 *)(data0 + data_cnt) |
+ (*(u8 *)(data0 + (data_cnt + 1))) << 8 |
+ (*(u8 *)(data0 + (data_cnt + 2))) << 16;
+ dev_dbg(dsim->dev, "count = 3 payload = %x, %x %x %x\n",
+ payload, *(u8 *)(data0 + data_cnt),
+ *(u8 *)(data0 + (data_cnt + 1)),
+ *(u8 *)(data0 + (data_cnt + 2)));
+ } else if ((data1 - data_cnt) == 2) {
+ payload = *(u8 *)(data0 + data_cnt) |
+ (*(u8 *)(data0 + (data_cnt + 1))) << 8;
+ dev_dbg(dsim->dev,
+ "count = 2 payload = %x, %x %x\n", payload,
+ *(u8 *)(data0 + data_cnt),
+ *(u8 *)(data0 + (data_cnt + 1)));
+ } else if ((data1 - data_cnt) == 1) {
+ payload = *(u8 *)(data0 + data_cnt);
+ }
+
+ s5p_mipi_dsi_wr_tx_data(dsim, payload);
+ /* send 4bytes per one time. */
+ } else {
+ payload = *(u8 *)(data0 + data_cnt) |
+ (*(u8 *)(data0 + (data_cnt + 1))) << 8 |
+ (*(u8 *)(data0 + (data_cnt + 2))) << 16 |
+ (*(u8 *)(data0 + (data_cnt + 3))) << 24;
+
+ dev_dbg(dsim->dev,
+ "count = 4 payload = %x, %x %x %x %x\n",
+ payload, *(u8 *)(data0 + data_cnt),
+ *(u8 *)(data0 + (data_cnt + 1)),
+ *(u8 *)(data0 + (data_cnt + 2)),
+ *(u8 *)(data0 + (data_cnt + 3)));
+
+ s5p_mipi_dsi_wr_tx_data(dsim, payload);
+ }
+ }
+}
+
+int s5p_mipi_dsi_wr_data(struct mipi_dsim_device *dsim, unsigned int data_id,
+ unsigned int data0, unsigned int data1)
+{
+ unsigned int timeout = TRY_GET_FIFO_TIMEOUT;
+ unsigned long delay_val, udelay;
+ unsigned int check_rx_ack = 0;
+
+ if (dsim->state == DSIM_STATE_ULPS) {
+ dev_err(dsim->dev, "state is ULPS.\n");
+
+ return -EINVAL;
+ }
+
+ delay_val = MHZ / dsim->dsim_config->esc_clk;
+ udelay = 10 * delay_val;
+
+ mdelay(udelay);
+
+ /* only if transfer mode is LPDT, wait SFR becomes empty. */
+ if (dsim->state == DSIM_STATE_STOP) {
+ while (!(s5p_mipi_dsi_get_fifo_state(dsim) &
+ SFR_HEADER_EMPTY)) {
+ if ((timeout--) > 0)
+ mdelay(1);
+ else {
+ dev_err(dsim->dev,
+ "SRF header fifo is not empty.\n");
+ return -EINVAL;
+ }
+ }
+ }
+
+ switch (data_id) {
+ /* short packet types of packet types for command. */
+ case MIPI_DSI_GENERIC_SHORT_WRITE_0_PARAM:
+ case MIPI_DSI_GENERIC_SHORT_WRITE_1_PARAM:
+ case MIPI_DSI_GENERIC_SHORT_WRITE_2_PARAM:
+ case MIPI_DSI_DCS_SHORT_WRITE:
+ case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
+ case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE:
+ s5p_mipi_dsi_wr_tx_header(dsim, data_id, data0, data1);
+ if (check_rx_ack)
+ /* process response func should be implemented */
+ return 0;
+ else
+ return -EINVAL;
+
+ /* general command */
+ case MIPI_DSI_COLOR_MODE_OFF:
+ case MIPI_DSI_COLOR_MODE_ON:
+ case MIPI_DSI_SHUTDOWN_PERIPHERAL:
+ case MIPI_DSI_TURN_ON_PERIPHERAL:
+ s5p_mipi_dsi_wr_tx_header(dsim, data_id, data0, data1);
+ if (check_rx_ack)
+ /* process response func should be implemented. */
+ return 0;
+ else
+ return -EINVAL;
+
+ /* packet types for video data */
+ case MIPI_DSI_V_SYNC_START:
+ case MIPI_DSI_V_SYNC_END:
+ case MIPI_DSI_H_SYNC_START:
+ case MIPI_DSI_H_SYNC_END:
+ case MIPI_DSI_END_OF_TRANSMISSION:
+ return 0;
+
+ /* short and response packet types for command */
+ case MIPI_DSI_GENERIC_READ_REQUEST_0_PARAM:
+ case MIPI_DSI_GENERIC_READ_REQUEST_1_PARAM:
+ case MIPI_DSI_GENERIC_READ_REQUEST_2_PARAM:
+ case MIPI_DSI_DCS_READ:
+ s5p_mipi_dsi_clear_all_interrupt(dsim);
+ s5p_mipi_dsi_wr_tx_header(dsim, data_id, data0, data1);
+ /* process response func should be implemented. */
+ return 0;
+
+ /* long packet type and null packet */
+ case MIPI_DSI_NULL_PACKET:
+ case MIPI_DSI_BLANKING_PACKET:
+ return 0;
+ case MIPI_DSI_GENERIC_LONG_WRITE:
+ case MIPI_DSI_DCS_LONG_WRITE:
+ {
+ unsigned int size, data_cnt = 0, payload = 0;
+
+ size = data1 * 4;
+
+ /* if data count is less then 4, then send 3bytes data. */
+ if (data1 < 4) {
+ payload = *(u8 *)(data0) |
+ *(u8 *)(data0 + 1) << 8 |
+ *(u8 *)(data0 + 2) << 16;
+
+ s5p_mipi_dsi_wr_tx_data(dsim, payload);
+
+ dev_dbg(dsim->dev, "count = %d payload = %x,%x %x %x\n",
+ data1, payload,
+ *(u8 *)(data0 + data_cnt),
+ *(u8 *)(data0 + (data_cnt + 1)),
+ *(u8 *)(data0 + (data_cnt + 2)));
+ /* in case that data count is more then 4 */
+ } else
+ s5p_mipi_dsi_long_data_wr(dsim, data0, data1);
+
+ /* put data into header fifo */
+ s5p_mipi_dsi_wr_tx_header(dsim, data_id, data1 & 0xff,
+ (data1 & 0xff00) >> 8);
+
+ }
+ if (check_rx_ack)
+ /* process response func should be implemented. */
+ return 0;
+ else
+ return -EINVAL;
+
+ /* packet typo for video data */
+ case MIPI_DSI_PACKED_PIXEL_STREAM_16:
+ case MIPI_DSI_PACKED_PIXEL_STREAM_18:
+ case MIPI_DSI_PIXEL_STREAM_3BYTE_18:
+ case MIPI_DSI_PACKED_PIXEL_STREAM_24:
+ if (check_rx_ack)
+ /* process response func should be implemented. */
+ return 0;
+ else
+ return -EINVAL;
+ default:
+ dev_warn(dsim->dev,
+ "data id %x is not supported current DSI spec.\n",
+ data_id);
+
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+int s5p_mipi_dsi_pll_on(struct mipi_dsim_device *dsim, unsigned int enable)
+{
+ int sw_timeout;
+
+ if (enable) {
+ sw_timeout = 1000;
+
+ s5p_mipi_dsi_clear_interrupt(dsim);
+ s5p_mipi_dsi_enable_pll(dsim, 1);
+ while (1) {
+ sw_timeout--;
+ if (s5p_mipi_dsi_is_pll_stable(dsim))
+ return 0;
+ if (sw_timeout == 0)
+ return -EINVAL;
+ }
+ } else
+ s5p_mipi_dsi_enable_pll(dsim, 0);
+
+ return 0;
+}
+
+unsigned long s5p_mipi_dsi_change_pll(struct mipi_dsim_device *dsim,
+ unsigned int pre_divider, unsigned int main_divider,
+ unsigned int scaler)
+{
+ unsigned long dfin_pll, dfvco, dpll_out;
+ unsigned int i, freq_band = 0xf;
+
+ dfin_pll = (FIN_HZ / pre_divider);
+
+ if (dfin_pll < DFIN_PLL_MIN_HZ || dfin_pll > DFIN_PLL_MAX_HZ) {
+ dev_warn(dsim->dev, "fin_pll range should be 6MHz ~ 12MHz\n");
+ s5p_mipi_dsi_enable_afc(dsim, 0, 0);
+ } else {
+ if (dfin_pll < 7 * MHZ)
+ s5p_mipi_dsi_enable_afc(dsim, 1, 0x1);
+ else if (dfin_pll < 8 * MHZ)
+ s5p_mipi_dsi_enable_afc(dsim, 1, 0x0);
+ else if (dfin_pll < 9 * MHZ)
+ s5p_mipi_dsi_enable_afc(dsim, 1, 0x3);
+ else if (dfin_pll < 10 * MHZ)
+ s5p_mipi_dsi_enable_afc(dsim, 1, 0x2);
+ else if (dfin_pll < 11 * MHZ)
+ s5p_mipi_dsi_enable_afc(dsim, 1, 0x5);
+ else
+ s5p_mipi_dsi_enable_afc(dsim, 1, 0x4);
+ }
+
+ dfvco = dfin_pll * main_divider;
+ dev_dbg(dsim->dev, "dfvco = %lu, dfin_pll = %lu, main_divider = %d\n",
+ dfvco, dfin_pll, main_divider);
+ if (dfvco < DFVCO_MIN_HZ || dfvco > DFVCO_MAX_HZ)
+ dev_warn(dsim->dev, "fvco range should be 500MHz ~ 1000MHz\n");
+
+ dpll_out = dfvco / (1 << scaler);
+ dev_dbg(dsim->dev, "dpll_out = %lu, dfvco = %lu, scaler = %d\n",
+ dpll_out, dfvco, scaler);
+
+ for (i = 0; i < ARRAY_SIZE(dpll_table); i++) {
+ if (dpll_out < dpll_table[i] * MHZ) {
+ freq_band = i;
+ break;
+ }
+ }
+
+ dev_dbg(dsim->dev, "freq_band = %d\n", freq_band);
+
+ s5p_mipi_dsi_pll_freq(dsim, pre_divider, main_divider, scaler);
+
+ s5p_mipi_dsi_hs_zero_ctrl(dsim, 0);
+ s5p_mipi_dsi_prep_ctrl(dsim, 0);
+
+ /* Freq Band */
+ s5p_mipi_dsi_pll_freq_band(dsim, freq_band);
+
+ /* Stable time */
+ s5p_mipi_dsi_pll_stable_time(dsim, dsim->dsim_config->pll_stable_time);
+
+ /* Enable PLL */
+ dev_dbg(dsim->dev, "FOUT of mipi dphy pll is %luMHz\n",
+ (dpll_out / MHZ));
+
+ return dpll_out;
+}
+
+int s5p_mipi_dsi_set_clock(struct mipi_dsim_device *dsim,
+ unsigned int byte_clk_sel, unsigned int enable)
+{
+ unsigned int esc_div;
+ unsigned long esc_clk_error_rate;
+
+ if (enable) {
+ dsim->e_clk_src = byte_clk_sel;
+
+ /* Escape mode clock and byte clock source */
+ s5p_mipi_dsi_set_byte_clock_src(dsim, byte_clk_sel);
+
+ /* DPHY, DSIM Link : D-PHY clock out */
+ if (byte_clk_sel == DSIM_PLL_OUT_DIV8) {
+ dsim->hs_clk = s5p_mipi_dsi_change_pll(dsim,
+ dsim->dsim_config->p, dsim->dsim_config->m,
+ dsim->dsim_config->s);
+ if (dsim->hs_clk == 0) {
+ dev_err(dsim->dev,
+ "failed to get hs clock.\n");
+ return -EINVAL;
+ }
+
+ dsim->byte_clk = dsim->hs_clk / 8;
+ s5p_mipi_dsi_enable_pll_bypass(dsim, 0);
+ s5p_mipi_dsi_pll_on(dsim, 1);
+ /* DPHY : D-PHY clock out, DSIM link : external clock out */
+ } else if (byte_clk_sel == DSIM_EXT_CLK_DIV8)
+ dev_warn(dsim->dev,
+ "this project is not support \
+ external clock source for MIPI DSIM\n");
+ else if (byte_clk_sel == DSIM_EXT_CLK_BYPASS)
+ dev_warn(dsim->dev,
+ "this project is not support \
+ external clock source for MIPI DSIM\n");
+
+ /* escape clock divider */
+ esc_div = dsim->byte_clk / (dsim->dsim_config->esc_clk);
+ dev_dbg(dsim->dev,
+ "esc_div = %d, byte_clk = %lu, esc_clk = %lu\n",
+ esc_div, dsim->byte_clk, dsim->dsim_config->esc_clk);
+ if ((dsim->byte_clk / esc_div) >= (20 * MHZ) ||
+ (dsim->byte_clk / esc_div) >
+ dsim->dsim_config->esc_clk)
+ esc_div += 1;
+
+ dsim->escape_clk = dsim->byte_clk / esc_div;
+ dev_dbg(dsim->dev,
+ "escape_clk = %lu, byte_clk = %lu, esc_div = %d\n",
+ dsim->escape_clk, dsim->byte_clk, esc_div);
+
+ /* enable escape clock. */
+ s5p_mipi_dsi_enable_byte_clock(dsim, DSIM_ESCCLK_ON);
+
+ /* enable byte clk and escape clock */
+ s5p_mipi_dsi_set_esc_clk_prs(dsim, 1, esc_div);
+ /* escape clock on lane */
+ s5p_mipi_dsi_enable_esc_clk_on_lane(dsim,
+ (DSIM_LANE_CLOCK | dsim->data_lane), 1);
+
+ dev_dbg(dsim->dev, "byte clock is %luMHz\n",
+ (dsim->byte_clk / MHZ));
+ dev_dbg(dsim->dev, "escape clock that user's need is %lu\n",
+ (dsim->dsim_config->esc_clk / MHZ));
+ dev_dbg(dsim->dev, "escape clock divider is %x\n", esc_div);
+ dev_dbg(dsim->dev, "escape clock is %luMHz\n",
+ ((dsim->byte_clk / esc_div) / MHZ));
+
+ if ((dsim->byte_clk / esc_div) > dsim->escape_clk) {
+ esc_clk_error_rate = dsim->escape_clk /
+ (dsim->byte_clk / esc_div);
+ dev_warn(dsim->dev, "error rate is %lu over.\n",
+ (esc_clk_error_rate / 100));
+ } else if ((dsim->byte_clk / esc_div) < (dsim->escape_clk)) {
+ esc_clk_error_rate = (dsim->byte_clk / esc_div) /
+ dsim->escape_clk;
+ dev_warn(dsim->dev, "error rate is %lu under.\n",
+ (esc_clk_error_rate / 100));
+ }
+ } else {
+ s5p_mipi_dsi_enable_esc_clk_on_lane(dsim,
+ (DSIM_LANE_CLOCK | dsim->data_lane), 0);
+ s5p_mipi_dsi_set_esc_clk_prs(dsim, 0, 0);
+
+ /* disable escape clock. */
+ s5p_mipi_dsi_enable_byte_clock(dsim, DSIM_ESCCLK_OFF);
+
+ if (byte_clk_sel == DSIM_PLL_OUT_DIV8)
+ s5p_mipi_dsi_pll_on(dsim, 0);
+ }
+
+ return 0;
+}
+
+int s5p_mipi_dsi_init_dsim(struct mipi_dsim_device *dsim)
+{
+ if (dsim->pd->init_d_phy)
+ dsim->pd->init_d_phy(dsim);
+
+ dsim->state = DSIM_STATE_INIT;
+
+ switch (dsim->dsim_config->e_no_data_lane) {
+ case DSIM_DATA_LANE_1:
+ dsim->data_lane = DSIM_LANE_DATA0;
+ break;
+ case DSIM_DATA_LANE_2:
+ dsim->data_lane = DSIM_LANE_DATA0 | DSIM_LANE_DATA1;
+ break;
+ case DSIM_DATA_LANE_3:
+ dsim->data_lane = DSIM_LANE_DATA0 | DSIM_LANE_DATA1 |
+ DSIM_LANE_DATA2;
+ break;
+ case DSIM_DATA_LANE_4:
+ dsim->data_lane = DSIM_LANE_DATA0 | DSIM_LANE_DATA1 |
+ DSIM_LANE_DATA2 | DSIM_LANE_DATA3;
+ break;
+ default:
+ dev_info(dsim->dev, "data lane is invalid.\n");
+ return -EINVAL;
+ };
+
+ s5p_mipi_dsi_sw_reset(dsim);
+ s5p_mipi_dsi_dp_dn_swap(dsim, 0);
+
+ return 0;
+}
+
+int s5p_mipi_dsi_enable_frame_done_int(struct mipi_dsim_device *dsim,
+ unsigned int enable)
+{
+ /* enable only frame done interrupt */
+ s5p_mipi_dsi_set_interrupt_mask(dsim, INTMSK_FRAME_DONE, enable);
+
+ return 0;
+}
+
+int s5p_mipi_dsi_set_display_mode(struct mipi_dsim_device *dsim,
+ struct mipi_dsim_config *dsim_config)
+{
+ struct fb_videomode *lcd_video = NULL;
+ struct s3c_fb_pd_win *pd;
+ unsigned int width = 0, height = 0;
+
+ pd = (struct s3c_fb_pd_win *)dsim->dsim_config->lcd_panel_info;
+ lcd_video = (struct fb_videomode *)&pd->win_mode;
+
+ width = lcd_video->xres;
+ height = lcd_video->yres;
+
+ /* in case of VIDEO MODE (RGB INTERFACE) */
+ if (dsim->dsim_config->e_interface == (u32) DSIM_VIDEO) {
+ if (dsim->dsim_config->auto_vertical_cnt == 0) {
+ s5p_mipi_dsi_set_main_disp_vporch(dsim,
+ lcd_video->upper_margin,
+ lcd_video->lower_margin, 0);
+ s5p_mipi_dsi_set_main_disp_hporch(dsim,
+ lcd_video->left_margin,
+ lcd_video->right_margin);
+ s5p_mipi_dsi_set_main_disp_sync_area(dsim,
+ lcd_video->vsync_len,
+ lcd_video->hsync_len);
+ }
+ }
+
+ s5p_mipi_dsi_set_main_disp_resol(dsim, height, width);
+
+ s5p_mipi_dsi_display_config(dsim, dsim->dsim_config);
+
+ return 0;
+}
+
+int s5p_mipi_dsi_init_link(struct mipi_dsim_device *dsim)
+{
+ unsigned int time_out = 100;
+
+ switch (dsim->state) {
+ case DSIM_STATE_INIT:
+ s5p_mipi_dsi_sw_reset(dsim);
+
+ s5p_mipi_dsi_init_fifo_pointer(dsim, 0x1f);
+
+ /* dsi configuration */
+ s5p_mipi_dsi_init_config(dsim);
+ s5p_mipi_dsi_enable_lane(dsim, DSIM_LANE_CLOCK, 1);
+ s5p_mipi_dsi_enable_lane(dsim, dsim->data_lane, 1);
+
+ /* set clock configuration */
+ s5p_mipi_dsi_set_clock(dsim, dsim->dsim_config->e_byte_clk, 1);
+
+ /* check clock and data lane state are stop state */
+ while (!(s5p_mipi_dsi_is_lane_state(dsim))) {
+ time_out--;
+ if (time_out == 0) {
+ dev_err(dsim->dev,
+ "DSI Master is not stop state.\n");
+ dev_err(dsim->dev,
+ "Check initialization process\n");
+
+ return -EINVAL;
+ }
+ }
+
+ if (time_out != 0) {
+ dev_info(dsim->dev,
+ "DSI Master driver has been completed.\n");
+ dev_info(dsim->dev, "DSI Master state is stop state\n");
+ }
+
+ dsim->state = DSIM_STATE_STOP;
+
+ /* BTA sequence counters */
+ s5p_mipi_dsi_set_stop_state_counter(dsim,
+ dsim->dsim_config->stop_holding_cnt);
+ s5p_mipi_dsi_set_bta_timeout(dsim,
+ dsim->dsim_config->bta_timeout);
+ s5p_mipi_dsi_set_lpdr_timeout(dsim,
+ dsim->dsim_config->rx_timeout);
+
+ return 0;
+ default:
+ dev_info(dsim->dev, "DSI Master is already init.\n");
+ return 0;
+ }
+
+ return 0;
+}
+
+int s5p_mipi_dsi_set_hs_enable(struct mipi_dsim_device *dsim)
+{
+ if (dsim->state == DSIM_STATE_STOP) {
+ if (dsim->e_clk_src != DSIM_EXT_CLK_BYPASS) {
+ dsim->state = DSIM_STATE_HSCLKEN;
+
+ /* set LCDC and CPU transfer mode to HS. */
+ s5p_mipi_dsi_set_lcdc_transfer_mode(dsim, 0);
+ s5p_mipi_dsi_set_cpu_transfer_mode(dsim, 0);
+
+ s5p_mipi_dsi_enable_hs_clock(dsim, 1);
+
+ return 0;
+ } else
+ dev_warn(dsim->dev,
+ "clock source is external bypass.\n");
+ } else
+ dev_warn(dsim->dev, "DSIM is not stop state.\n");
+
+ return 0;
+}
+
+int s5p_mipi_dsi_set_data_transfer_mode(struct mipi_dsim_device *dsim,
+ unsigned int mode)
+{
+ if (mode) {
+ if (dsim->state != DSIM_STATE_HSCLKEN) {
+ dev_err(dsim->dev, "HS Clock lane is not enabled.\n");
+ return -EINVAL;
+ }
+
+ s5p_mipi_dsi_set_lcdc_transfer_mode(dsim, 0);
+ } else {
+ if (dsim->state == DSIM_STATE_INIT || dsim->state ==
+ DSIM_STATE_ULPS) {
+ dev_err(dsim->dev,
+ "DSI Master is not STOP or HSDT state.\n");
+ return -EINVAL;
+ }
+
+ s5p_mipi_dsi_set_cpu_transfer_mode(dsim, 0);
+ }
+
+ return 0;
+}
+
+int s5p_mipi_dsi_get_frame_done_status(struct mipi_dsim_device *dsim)
+{
+ return _s5p_mipi_dsi_get_frame_done_status(dsim);
+}
+
+int s5p_mipi_dsi_clear_frame_done(struct mipi_dsim_device *dsim)
+{
+ _s5p_mipi_dsi_clear_frame_done(dsim);
+
+ return 0;
+}
+
+MODULE_AUTHOR("InKi Dae <inki.dae at samsung.com>");
+MODULE_DESCRIPTION("Samusung MIPI-DSIM common driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/video/s5p_mipi_dsi_common.h b/drivers/video/s5p_mipi_dsi_common.h
new file mode 100644
index 0000000..040d70e
--- /dev/null
+++ b/drivers/video/s5p_mipi_dsi_common.h
@@ -0,0 +1,38 @@
+/* linux/drivers/video/s5p_mipi_dsi_common.h
+ *
+ * Header file for Samsung MIPI-DSI common driver.
+ *
+ * Copyright (c) 2009 Samsung Electronics
+ * InKi Dae <inki.dae at samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef _S5P_MIPI_DSI_COMMON_H
+#define _S5P_MIPI_DSI_COMMON_H
+
+int s5p_mipi_dsi_wr_data(struct mipi_dsim_device *dsim, unsigned int data_id,
+ unsigned int data0, unsigned int data1);
+int s5p_mipi_dsi_pll_on(struct mipi_dsim_device *dsim, unsigned int enable);
+unsigned long s5p_mipi_dsi_change_pll(struct mipi_dsim_device *dsim,
+ unsigned int pre_divider, unsigned int main_divider,
+ unsigned int scaler);
+int s5p_mipi_dsi_set_clock(struct mipi_dsim_device *dsim,
+ unsigned int byte_clk_sel, unsigned int enable);
+int s5p_mipi_dsi_init_dsim(struct mipi_dsim_device *dsim);
+int s5p_mipi_dsi_set_display_mode(struct mipi_dsim_device *dsim,
+ struct mipi_dsim_config *dsim_info);
+int s5p_mipi_dsi_init_link(struct mipi_dsim_device *dsim);
+int s5p_mipi_dsi_set_hs_enable(struct mipi_dsim_device *dsim);
+int s5p_mipi_dsi_set_data_transfer_mode(struct mipi_dsim_device *dsim,
+ unsigned int mode);
+int s5p_mipi_dsi_enable_frame_done_int(struct mipi_dsim_device *dsim,
+ unsigned int enable);
+int s5p_mipi_dsi_get_frame_done_status(struct mipi_dsim_device *dsim);
+int s5p_mipi_dsi_clear_frame_done(struct mipi_dsim_device *dsim);
+
+extern struct fb_info *registered_fb[FB_MAX] __read_mostly;
+
+#endif /* _S5P_MIPI_DSI_COMMON_H */
diff --git a/drivers/video/s5p_mipi_dsi_lowlevel.c b/drivers/video/s5p_mipi_dsi_lowlevel.c
new file mode 100644
index 0000000..8afea36
--- /dev/null
+++ b/drivers/video/s5p_mipi_dsi_lowlevel.c
@@ -0,0 +1,553 @@
+/* linux/drivers/video/s5p_mipi_dsi_lowlevel.c
+ *
+ * Samsung MIPI-DSI lowlevel driver.
+ *
+ * InKi Dae, <inki.dae at samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/mutex.h>
+#include <linux/wait.h>
+#include <linux/delay.h>
+#include <linux/fs.h>
+#include <linux/mm.h>
+#include <linux/ctype.h>
+#include <linux/io.h>
+
+#include <mach/map.h>
+
+#include <plat/dsim.h>
+#include <plat/regs-dsim.h>
+
+void s5p_mipi_dsi_func_reset(struct mipi_dsim_device *dsim)
+{
+ unsigned int reg;
+
+ reg = readl(dsim->reg_base + S5P_DSIM_SWRST);
+
+ reg |= DSIM_FUNCRST;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_SWRST);
+}
+
+void s5p_mipi_dsi_sw_reset(struct mipi_dsim_device *dsim)
+{
+ unsigned int reg;
+
+ reg = readl(dsim->reg_base + S5P_DSIM_SWRST);
+
+ reg |= DSIM_SWRST;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_SWRST);
+}
+
+void s5p_mipi_dsi_set_interrupt_mask(struct mipi_dsim_device *dsim,
+ unsigned int mode, unsigned int mask)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_INTMSK);
+
+ if (mask)
+ reg |= mode;
+ else
+ reg &= ~mode;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_INTMSK);
+}
+
+void s5p_mipi_dsi_init_fifo_pointer(struct mipi_dsim_device *dsim,
+ unsigned int cfg)
+{
+ unsigned int reg;
+
+ reg = readl(dsim->reg_base + S5P_DSIM_FIFOCTRL);
+
+ writel(reg & ~(cfg), dsim->reg_base + S5P_DSIM_FIFOCTRL);
+ mdelay(10);
+ reg |= cfg;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_FIFOCTRL);
+}
+
+/*
+ * this function set PLL P, M and S value in D-PHY
+ */
+void s5p_mipi_dsi_set_phy_tunning(struct mipi_dsim_device *dsim,
+ unsigned int value)
+{
+ writel(DSIM_AFC_CTL(value), dsim->reg_base + S5P_DSIM_PHYACCHR);
+}
+
+void s5p_mipi_dsi_set_main_disp_resol(struct mipi_dsim_device *dsim,
+ unsigned int vert_resol, unsigned int hori_resol)
+{
+ unsigned int reg;
+
+ /* standby should be set after configuration so set to not ready*/
+ reg = (readl(dsim->reg_base + S5P_DSIM_MDRESOL)) &
+ ~(DSIM_MAIN_STAND_BY);
+ writel(reg, dsim->reg_base + S5P_DSIM_MDRESOL);
+
+ reg &= ~(0x7ff << 16) & ~(0x7ff << 0);
+ reg |= DSIM_MAIN_VRESOL(vert_resol) | DSIM_MAIN_HRESOL(hori_resol);
+
+ reg |= DSIM_MAIN_STAND_BY;
+ writel(reg, dsim->reg_base + S5P_DSIM_MDRESOL);
+}
+
+void s5p_mipi_dsi_set_main_disp_vporch(struct mipi_dsim_device *dsim,
+ unsigned int cmd_allow, unsigned int vfront, unsigned int vback)
+{
+ unsigned int reg;
+
+ reg = (readl(dsim->reg_base + S5P_DSIM_MVPORCH)) &
+ ~(DSIM_CMD_ALLOW_MASK) & ~(DSIM_STABLE_VFP_MASK) &
+ ~(DSIM_MAIN_VBP_MASK);
+
+ reg |= ((cmd_allow & 0xf) << DSIM_CMD_ALLOW_SHIFT) |
+ ((vfront & 0x7ff) << DSIM_STABLE_VFP_SHIFT) |
+ ((vback & 0x7ff) << DSIM_MAIN_VBP_SHIFT);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_MVPORCH);
+}
+
+void s5p_mipi_dsi_set_main_disp_hporch(struct mipi_dsim_device *dsim,
+ unsigned int front, unsigned int back)
+{
+ unsigned int reg;
+
+ reg = (readl(dsim->reg_base + S5P_DSIM_MHPORCH)) &
+ ~(DSIM_MAIN_HFP_MASK) & ~(DSIM_MAIN_HBP_MASK);
+
+ reg |= (front << DSIM_MAIN_HFP_SHIFT) | (back << DSIM_MAIN_HBP_SHIFT);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_MHPORCH);
+}
+
+void s5p_mipi_dsi_set_main_disp_sync_area(struct mipi_dsim_device *dsim,
+ unsigned int vert, unsigned int hori)
+{
+ unsigned int reg;
+
+ reg = (readl(dsim->reg_base + S5P_DSIM_MSYNC)) &
+ ~(DSIM_MAIN_VSA_MASK) & ~(DSIM_MAIN_HSA_MASK);
+
+ reg |= ((vert & 0x3ff) << DSIM_MAIN_VSA_SHIFT) |
+ (hori << DSIM_MAIN_HSA_SHIFT);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_MSYNC);
+}
+
+void s5p_mipi_dsi_set_sub_disp_resol(struct mipi_dsim_device *dsim,
+ unsigned int vert, unsigned int hori)
+{
+ unsigned int reg;
+
+ reg = (readl(dsim->reg_base + S5P_DSIM_SDRESOL)) &
+ ~(DSIM_SUB_STANDY_MASK);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_SDRESOL);
+
+ reg &= ~(DSIM_SUB_VRESOL_MASK) | ~(DSIM_SUB_HRESOL_MASK);
+ reg |= ((vert & 0x7ff) << DSIM_SUB_VRESOL_SHIFT) |
+ ((hori & 0x7ff) << DSIM_SUB_HRESOL_SHIFT);
+ writel(reg, dsim->reg_base + S5P_DSIM_SDRESOL);
+
+ reg |= (1 << DSIM_SUB_STANDY_SHIFT);
+ writel(reg, dsim->reg_base + S5P_DSIM_SDRESOL);
+}
+
+void s5p_mipi_dsi_init_config(struct mipi_dsim_device *dsim)
+{
+ struct mipi_dsim_config *dsim_config = dsim->dsim_config;
+
+ unsigned int cfg = (readl(dsim->reg_base + S5P_DSIM_CONFIG)) &
+ ~(1 << 28) & ~(0x1f << 20) & ~(0x3 << 5);
+
+ cfg = (dsim_config->auto_flush << 29) |
+ (dsim_config->eot_disable << 28) |
+ (dsim_config->auto_vertical_cnt << DSIM_AUTO_MODE_SHIFT) |
+ (dsim_config->hse << DSIM_HSE_MODE_SHIFT) |
+ (dsim_config->hfp << DSIM_HFP_MODE_SHIFT) |
+ (dsim_config->hbp << DSIM_HBP_MODE_SHIFT) |
+ (dsim_config->hsa << DSIM_HSA_MODE_SHIFT) |
+ (dsim_config->e_no_data_lane << DSIM_NUM_OF_DATALANE_SHIFT);
+
+ writel(cfg, dsim->reg_base + S5P_DSIM_CONFIG);
+}
+
+void s5p_mipi_dsi_display_config(struct mipi_dsim_device *dsim,
+ struct mipi_dsim_config *dsim_config)
+{
+ u32 reg = (readl(dsim->reg_base + S5P_DSIM_CONFIG)) &
+ ~(0x3 << 26) & ~(1 << 25) & ~(0x3 << 18) & ~(0x7 << 12) &
+ ~(0x3 << 16) & ~(0x7 << 8);
+
+ if (dsim_config->e_interface == DSIM_VIDEO)
+ reg |= (1 << 25);
+ else if (dsim_config->e_interface == DSIM_COMMAND)
+ reg &= ~(1 << 25);
+ else {
+ dev_err(dsim->dev, "this ddi is not MIPI interface.\n");
+ return;
+ }
+
+ /* main lcd */
+ reg |= ((u8) (dsim_config->e_burst_mode) & 0x3) << 26 |
+ ((u8) (dsim_config->e_virtual_ch) & 0x3) << 18 |
+ ((u8) (dsim_config->e_pixel_format) & 0x7) << 12;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_CONFIG);
+}
+
+void s5p_mipi_dsi_enable_lane(struct mipi_dsim_device *dsim, unsigned int lane,
+ unsigned int enable)
+{
+ unsigned int reg;
+
+ reg = readl(dsim->reg_base + S5P_DSIM_CONFIG);
+
+ if (enable)
+ reg |= DSIM_LANE_ENx(lane);
+ else
+ reg &= ~DSIM_LANE_ENx(lane);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_CONFIG);
+}
+
+
+void s5p_mipi_dsi_set_data_lane_number(struct mipi_dsim_device *dsim,
+ unsigned int count)
+{
+ unsigned int cfg;
+
+ /* get the data lane number. */
+ cfg = DSIM_NUM_OF_DATA_LANE(count);
+
+ writel(cfg, dsim->reg_base + S5P_DSIM_CONFIG);
+}
+
+void s5p_mipi_dsi_enable_afc(struct mipi_dsim_device *dsim, unsigned int enable,
+ unsigned int afc_code)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_PHYACCHR);
+
+ if (enable) {
+ reg |= (1 << 14);
+ reg &= ~(0x7 << 5);
+ reg |= (afc_code & 0x7) << 5;
+ } else
+ reg &= ~(1 << 14);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_PHYACCHR);
+}
+
+void s5p_mipi_dsi_enable_pll_bypass(struct mipi_dsim_device *dsim,
+ unsigned int enable)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_CLKCTRL)) &
+ ~(DSIM_PLL_BYPASS_EXTERNAL);
+
+ reg |= enable << DSIM_PLL_BYPASS_SHIFT;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
+}
+
+void s5p_mipi_dsi_set_pll_pms(struct mipi_dsim_device *dsim, unsigned int p,
+ unsigned int m, unsigned int s)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_PLLCTRL);
+
+ reg |= ((p & 0x3f) << 13) | ((m & 0x1ff) << 4) | ((s & 0x7) << 1);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
+}
+
+void s5p_mipi_dsi_pll_freq_band(struct mipi_dsim_device *dsim,
+ unsigned int freq_band)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_PLLCTRL)) &
+ ~(0x1f << DSIM_FREQ_BAND_SHIFT);
+
+ reg |= ((freq_band & 0x1f) << DSIM_FREQ_BAND_SHIFT);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
+}
+
+void s5p_mipi_dsi_pll_freq(struct mipi_dsim_device *dsim,
+ unsigned int pre_divider, unsigned int main_divider,
+ unsigned int scaler)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_PLLCTRL)) &
+ ~(0x7ffff << 1);
+
+ reg |= (pre_divider & 0x3f) << 13 | (main_divider & 0x1ff) << 4 |
+ (scaler & 0x7) << 1;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
+}
+
+void s5p_mipi_dsi_pll_stable_time(struct mipi_dsim_device *dsim,
+ unsigned int lock_time)
+{
+ writel(lock_time, dsim->reg_base + S5P_DSIM_PLLTMR);
+}
+
+void s5p_mipi_dsi_enable_pll(struct mipi_dsim_device *dsim, unsigned int enable)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_PLLCTRL)) &
+ ~(0x1 << DSIM_PLL_EN_SHIFT);
+
+ reg |= ((enable & 0x1) << DSIM_PLL_EN_SHIFT);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
+}
+
+void s5p_mipi_dsi_set_byte_clock_src(struct mipi_dsim_device *dsim,
+ unsigned int src)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_CLKCTRL)) &
+ ~(0x3 << DSIM_BYTE_CLK_SRC_SHIFT);
+
+ reg |= ((unsigned int) src) << DSIM_BYTE_CLK_SRC_SHIFT;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
+}
+
+void s5p_mipi_dsi_enable_byte_clock(struct mipi_dsim_device *dsim,
+ unsigned int enable)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_CLKCTRL)) &
+ ~(1 << DSIM_BYTE_CLKEN_SHIFT);
+
+ reg |= enable << DSIM_BYTE_CLKEN_SHIFT;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
+}
+
+void s5p_mipi_dsi_set_esc_clk_prs(struct mipi_dsim_device *dsim,
+ unsigned int enable, unsigned int prs_val)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_CLKCTRL)) &
+ ~(1 << DSIM_ESC_CLKEN_SHIFT) & ~(0xffff);
+
+ reg |= enable << DSIM_ESC_CLKEN_SHIFT;
+ if (enable)
+ reg |= prs_val;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
+}
+
+void s5p_mipi_dsi_enable_esc_clk_on_lane(struct mipi_dsim_device *dsim,
+ unsigned int lane_sel, unsigned int enable)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_CLKCTRL);
+
+ if (enable)
+ reg |= DSIM_LANE_ESC_CLKEN(lane_sel);
+ else
+
+ reg &= ~DSIM_LANE_ESC_CLKEN(lane_sel);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
+}
+
+void s5p_mipi_dsi_force_dphy_stop_state(struct mipi_dsim_device *dsim,
+ unsigned int enable)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_ESCMODE)) &
+ ~(0x1 << DSIM_FORCE_STOP_STATE_SHIFT);
+
+ reg |= ((enable & 0x1) << DSIM_FORCE_STOP_STATE_SHIFT);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_ESCMODE);
+}
+
+unsigned int s5p_mipi_dsi_is_lane_state(struct mipi_dsim_device *dsim)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_STATUS);
+
+ /**
+ * check clock and data lane states.
+ * if MIPI-DSI controller was enabled at bootloader then
+ * TX_READY_HS_CLK is enabled otherwise STOP_STATE_CLK.
+ * so it should be checked for two case.
+ */
+ if ((reg & DSIM_STOP_STATE_DAT(0xf)) &&
+ ((reg & DSIM_STOP_STATE_CLK) ||
+ (reg & DSIM_TX_READY_HS_CLK)))
+ return 1;
+ else
+ return 0;
+
+ return 0;
+}
+
+void s5p_mipi_dsi_set_stop_state_counter(struct mipi_dsim_device *dsim,
+ unsigned int cnt_val)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_ESCMODE)) &
+ ~(0x7ff << DSIM_STOP_STATE_CNT_SHIFT);
+
+ reg |= ((cnt_val & 0x7ff) << DSIM_STOP_STATE_CNT_SHIFT);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_ESCMODE);
+}
+
+void s5p_mipi_dsi_set_bta_timeout(struct mipi_dsim_device *dsim,
+ unsigned int timeout)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_TIMEOUT)) &
+ ~(0xff << DSIM_BTA_TOUT_SHIFT);
+
+ reg |= (timeout << DSIM_BTA_TOUT_SHIFT);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_TIMEOUT);
+}
+
+void s5p_mipi_dsi_set_lpdr_timeout(struct mipi_dsim_device *dsim,
+ unsigned int timeout)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_TIMEOUT)) &
+ ~(0xffff << DSIM_LPDR_TOUT_SHIFT);
+
+ reg |= (timeout << DSIM_LPDR_TOUT_SHIFT);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_TIMEOUT);
+}
+
+void s5p_mipi_dsi_set_cpu_transfer_mode(struct mipi_dsim_device *dsim,
+ unsigned int lp)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_ESCMODE);
+
+ reg &= ~DSIM_CMD_LPDT_LP;
+
+ reg |= lp << DSIM_CMD_LPDT_SHIFT;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_ESCMODE);
+}
+
+void s5p_mipi_dsi_set_lcdc_transfer_mode(struct mipi_dsim_device *dsim,
+ unsigned int lp)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_ESCMODE);
+
+ reg &= ~DSIM_TX_LPDT_LP;
+
+ reg |= lp << DSIM_TX_LPDT_SHIFT;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_ESCMODE);
+}
+
+void s5p_mipi_dsi_enable_hs_clock(struct mipi_dsim_device *dsim,
+ unsigned int enable)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_CLKCTRL)) &
+ ~(1 << DSIM_TX_REQUEST_HSCLK_SHIFT);
+
+ reg |= enable << DSIM_TX_REQUEST_HSCLK_SHIFT;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_CLKCTRL);
+}
+
+void s5p_mipi_dsi_dp_dn_swap(struct mipi_dsim_device *dsim,
+ unsigned int swap_en)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_PHYACCHR1);
+
+ reg &= ~(0x3 << 0);
+ reg |= (swap_en & 0x3) << 0;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_PHYACCHR1);
+}
+
+void s5p_mipi_dsi_hs_zero_ctrl(struct mipi_dsim_device *dsim,
+ unsigned int hs_zero)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_PLLCTRL)) &
+ ~(0xf << 28);
+
+ reg |= ((hs_zero & 0xf) << 28);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
+}
+
+void s5p_mipi_dsi_prep_ctrl(struct mipi_dsim_device *dsim, unsigned int prep)
+{
+ unsigned int reg = (readl(dsim->reg_base + S5P_DSIM_PLLCTRL)) &
+ ~(0x7 << 20);
+
+ reg |= ((prep & 0x7) << 20);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_PLLCTRL);
+}
+
+void s5p_mipi_dsi_clear_interrupt(struct mipi_dsim_device *dsim)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_INTSRC);
+
+ reg |= INTSRC_PLL_STABLE;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_INTSRC);
+}
+
+void s5p_mipi_dsi_clear_all_interrupt(struct mipi_dsim_device *dsim)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_INTSRC);
+
+ reg |= 0xffffffff;
+
+ writel(reg, dsim->reg_base + S5P_DSIM_INTSRC);
+}
+
+unsigned int s5p_mipi_dsi_is_pll_stable(struct mipi_dsim_device *dsim)
+{
+ unsigned int reg;
+
+ reg = readl(dsim->reg_base + S5P_DSIM_STATUS);
+
+ return reg & (1 << 31) ? 1 : 0;
+}
+
+unsigned int s5p_mipi_dsi_get_fifo_state(struct mipi_dsim_device *dsim)
+{
+ unsigned int ret;
+
+ ret = readl(dsim->reg_base + S5P_DSIM_FIFOCTRL) & ~(0x1f);
+
+ return ret;
+}
+
+void s5p_mipi_dsi_wr_tx_header(struct mipi_dsim_device *dsim,
+ unsigned int di, unsigned int data0, unsigned int data1)
+{
+ unsigned int reg = (data1 << 16) | (data0 << 8) | ((di & 0x3f) << 0);
+
+ writel(reg, dsim->reg_base + S5P_DSIM_PKTHDR);
+}
+
+unsigned int _s5p_mipi_dsi_get_frame_done_status(struct mipi_dsim_device *dsim)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_INTSRC);
+
+ return (reg & INTSRC_FRAME_DONE) ? 1 : 0;
+}
+
+void _s5p_mipi_dsi_clear_frame_done(struct mipi_dsim_device *dsim)
+{
+ unsigned int reg = readl(dsim->reg_base + S5P_DSIM_INTSRC);
+
+ writel(reg | INTSRC_FRAME_DONE, dsim->reg_base +
+ S5P_DSIM_INTSRC);
+}
+
+void s5p_mipi_dsi_wr_tx_data(struct mipi_dsim_device *dsim,
+ unsigned int tx_data)
+{
+ writel(tx_data, dsim->reg_base + S5P_DSIM_PAYLOAD);
+}
diff --git a/drivers/video/s5p_mipi_dsi_lowlevel.h b/drivers/video/s5p_mipi_dsi_lowlevel.h
new file mode 100644
index 0000000..ed3f91c
--- /dev/null
+++ b/drivers/video/s5p_mipi_dsi_lowlevel.h
@@ -0,0 +1,98 @@
+/* linux/drivers/video/s5p_mipi_dsi_lowlevel.h
+ *
+ * Header file for Samsung MIPI-DSI lowlevel driver.
+ *
+ * Copyright (c) 2009 Samsung Electronics
+ * InKi Dae <inki.dae at samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef _S5P_MIPI_DSI_LOWLEVEL_H
+#define _S5P_MIPI_DSI_LOWLEVEL_H
+
+void s5p_mipi_dsi_func_reset(struct mipi_dsim_device *dsim);
+void s5p_mipi_dsi_sw_reset(struct mipi_dsim_device *dsim);
+void s5p_mipi_dsi_set_interrupt_mask(struct mipi_dsim_device *dsim,
+ unsigned int mode, unsigned int mask);
+void s5p_mipi_dsi_set_data_lane_number(struct mipi_dsim_device *dsim,
+ unsigned int count);
+void s5p_mipi_dsi_init_fifo_pointer(struct mipi_dsim_device *dsim,
+ unsigned int cfg);
+void s5p_mipi_dsi_set_phy_tunning(struct mipi_dsim_device *dsim,
+ unsigned int value);
+void s5p_mipi_dsi_set_phy_tunning(struct mipi_dsim_device *dsim,
+ unsigned int value);
+void s5p_mipi_dsi_set_main_disp_resol(struct mipi_dsim_device *dsim,
+ unsigned int vert_resol, unsigned int hori_resol);
+void s5p_mipi_dsi_set_main_disp_vporch(struct mipi_dsim_device *dsim,
+ unsigned int cmd_allow, unsigned int vfront, unsigned int vback);
+void s5p_mipi_dsi_set_main_disp_hporch(struct mipi_dsim_device *dsim,
+ unsigned int front, unsigned int back);
+void s5p_mipi_dsi_set_main_disp_sync_area(struct mipi_dsim_device *dsim,
+ unsigned int vert, unsigned int hori);
+void s5p_mipi_dsi_set_sub_disp_resol(struct mipi_dsim_device *dsim,
+ unsigned int vert, unsigned int hori);
+void s5p_mipi_dsi_init_config(struct mipi_dsim_device *dsim);
+void s5p_mipi_dsi_display_config(struct mipi_dsim_device *dsim,
+ struct mipi_dsim_config *dsim_config);
+void s5p_mipi_dsi_set_data_lane_number(struct mipi_dsim_device *dsim,
+ unsigned int count);
+void s5p_mipi_dsi_enable_lane(struct mipi_dsim_device *dsim, unsigned int lane,
+ unsigned int enable);
+void s5p_mipi_dsi_enable_afc(struct mipi_dsim_device *dsim, unsigned int enable,
+ unsigned int afc_code);
+void s5p_mipi_dsi_enable_pll_bypass(struct mipi_dsim_device *dsim,
+ unsigned int enable);
+void s5p_mipi_dsi_set_pll_pms(struct mipi_dsim_device *dsim, unsigned int p,
+ unsigned int m, unsigned int s);
+void s5p_mipi_dsi_pll_freq_band(struct mipi_dsim_device *dsim,
+ unsigned int freq_band);
+void s5p_mipi_dsi_pll_freq(struct mipi_dsim_device *dsim,
+ unsigned int pre_divider, unsigned int main_divider,
+ unsigned int scaler);
+void s5p_mipi_dsi_pll_stable_time(struct mipi_dsim_device *dsim,
+ unsigned int lock_time);
+void s5p_mipi_dsi_enable_pll(struct mipi_dsim_device *dsim,
+ unsigned int enable);
+void s5p_mipi_dsi_set_byte_clock_src(struct mipi_dsim_device *dsim,
+ unsigned int src);
+void s5p_mipi_dsi_enable_byte_clock(struct mipi_dsim_device *dsim,
+ unsigned int enable);
+void s5p_mipi_dsi_set_esc_clk_prs(struct mipi_dsim_device *dsim,
+ unsigned int enable, unsigned int prs_val);
+void s5p_mipi_dsi_enable_esc_clk_on_lane(struct mipi_dsim_device *dsim,
+ unsigned int lane_sel, unsigned int enable);
+void s5p_mipi_dsi_force_dphy_stop_state(struct mipi_dsim_device *dsim,
+ unsigned int enable);
+unsigned int s5p_mipi_dsi_is_lane_state(struct mipi_dsim_device *dsim);
+void s5p_mipi_dsi_set_stop_state_counter(struct mipi_dsim_device *dsim,
+ unsigned int cnt_val);
+void s5p_mipi_dsi_set_bta_timeout(struct mipi_dsim_device *dsim,
+ unsigned int timeout);
+void s5p_mipi_dsi_set_lpdr_timeout(struct mipi_dsim_device *dsim,
+ unsigned int timeout);
+void s5p_mipi_dsi_set_lcdc_transfer_mode(struct mipi_dsim_device *dsim,
+ unsigned int lp);
+void s5p_mipi_dsi_set_cpu_transfer_mode(struct mipi_dsim_device *dsim,
+ unsigned int lp);
+void s5p_mipi_dsi_enable_hs_clock(struct mipi_dsim_device *dsim,
+ unsigned int enable);
+void s5p_mipi_dsi_dp_dn_swap(struct mipi_dsim_device *dsim,
+ unsigned int swap_en);
+void s5p_mipi_dsi_hs_zero_ctrl(struct mipi_dsim_device *dsim,
+ unsigned int hs_zero);
+void s5p_mipi_dsi_prep_ctrl(struct mipi_dsim_device *dsim, unsigned int prep);
+void s5p_mipi_dsi_clear_interrupt(struct mipi_dsim_device *dsim);
+void s5p_mipi_dsi_clear_all_interrupt(struct mipi_dsim_device *dsim);
+unsigned int s5p_mipi_dsi_is_pll_stable(struct mipi_dsim_device *dsim);
+unsigned int s5p_mipi_dsi_get_fifo_state(struct mipi_dsim_device *dsim);
+unsigned int _s5p_mipi_dsi_get_frame_done_status(struct mipi_dsim_device *dsim);
+void _s5p_mipi_dsi_clear_frame_done(struct mipi_dsim_device *dsim);
+void s5p_mipi_dsi_wr_tx_header(struct mipi_dsim_device *dsim, unsigned int di,
+ unsigned int data0, unsigned int data1);
+void s5p_mipi_dsi_wr_tx_data(struct mipi_dsim_device *dsim,
+ unsigned int tx_data);
+
+#endif /* _S5P_MIPI_DSI_LOWLEVEL_H */
--
1.7.0.4
More information about the linux-arm-kernel
mailing list