[PATCH v2] OMAP3EVM: ehci: Fix EHCI support

[Bryan DE FARIA]

Set the VAUX2 regulator supply to 1.8V for the HSUSB host interface.
Gpio 2 of the TPS65950 has to be set to zero in order to enable the HSUBS2 clock.

Signed-off-by: Bryan DE FARIA <bdefaria at adeneo-embedded.com>
---
 arch/arm/mach-omap2/board-omap3evm.c |   25 +++++++++++++++++++++++++
 1 files changed, 25 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index c452b3f..13a2b71 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -377,6 +377,10 @@ static int omap3evm_twl_gpio_setup(struct device *dev,
 	if (r)
 		printk(KERN_ERR "failed to get/set lcd_bkl gpio\n");
 
+	/* gpio + 2 == HSUSB2 Clock Enable */
+	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
+		gpio_request_one(gpio + 2, GPIOF_OUT_INIT_LOW, "EN_HSUSB2_CLK");
+
 	/* gpio + 7 == DVI Enable */
 	gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
 
@@ -450,6 +454,25 @@ static struct regulator_init_data omap3evm_vio = {
 	.consumer_supplies	= omap3evm_vio_supply,
 };
 
+/* VAUX2 for EHCI */
+static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
+	REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
+};
+
+static struct regulator_init_data omap3evm_vaux2 = {
+	.constraints = {
+		.min_uV      		= 1800000,
+		.max_uV      		= 1800000,
+		.apply_uV    		= true,
+		.valid_modes_mask  	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask  	= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = ARRAY_SIZE(omap3evm_vaux2_supplies),
+	.consumer_supplies   	= omap3evm_vaux2_supplies,
+};
+
 #ifdef CONFIG_WL12XX_PLATFORM_DATA
 
 #define OMAP3EVM_WLAN_PMENA_GPIO	(150)
@@ -510,6 +533,8 @@ static int __init omap3_evm_i2c_init(void)
 
 	omap3evm_twldata.vdac->constraints.apply_uV = true;
 	omap3evm_twldata.vpll2->constraints.apply_uV = true;
+	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
+		omap3evm_twldata.vaux2 = &omap3evm_vaux2;
 
 	omap3_pmic_init("twl4030", &omap3evm_twldata);
 	omap_register_i2c_bus(2, 400, NULL, 0);
-- 
1.7.4.1