[PATCH v2 2/2] pxa/hx4700: Add Synaptics NavPoint (PXA27x SSP/SPI) driver
Marek Vasut
marek.vasut at gmail.com
Tue Aug 16 05:13:22 EDT 2011
On Thursday, August 11, 2011 06:26:30 PM Paul Parsons wrote:
> Add support for the Synaptics NavPoint connected to a PXA27x SSP port in
> SPI slave mode. The driver implements a simple navigation pad. The four
> raised dots are mapped to UP/DOWN/LEFT/RIGHT buttons and the centre of the
> touchpad is mapped to the ENTER button.
>
> Signed-off-by: Paul Parsons <lost.distance at yahoo.com>
> ---
>
> V2: Split into 2 parts for hx4700 specific code and navpoint driver. Added
> GPIO23_SSP1_SCLK_IN and GPIO102_NAVPOINT_PWR to mfp-pxa27x.h. Replaced
> power on/off callback with gpio number. Added msleep() to SSP port ready
> loop.
>
> diff -uprN clean-3.0.1/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h
> linux-3.0.1/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h ---
> clean-3.0.1/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h 2011-08-05
> 05:59:21.000000000 +0100 +++
> linux-3.0.1/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h 2011-08-11
> 16:49:00.004450942 +0100 @@ -206,6 +206,7 @@
> #define GPIO113_I2S_SYSCLK MFP_CFG_OUT(GPIO113, AF1, DRIVE_LOW)
>
> /* SSP 1 */
> +#define GPIO23_SSP1_SCLK_IN MFP_CFG_IN(GPIO23, AF2)
> #define GPIO23_SSP1_SCLK MFP_CFG_OUT(GPIO23, AF2, DRIVE_LOW)
> #define GPIO29_SSP1_SCLK MFP_CFG_IN(GPIO29, AF3)
> #define GPIO27_SSP1_SYSCLK MFP_CFG_OUT(GPIO27, AF1, DRIVE_LOW)
> @@ -434,6 +435,9 @@
> #define GPIO112_nMSINS MFP_CFG_IN(GPIO112, AF2)
> #define GPIO32_MSSCLK MFP_CFG_OUT(GPIO32, AF1, DRIVE_LOW)
>
> +/* Touchpad Controller */
> +#define GPIO102_NAVPOINT_PWR MFP_CFG_OUT(GPIO102, AF0, DRIVE_LOW)
> +
> /* commonly used pin configurations */
> #define GPIOxx_LCD_16BPP \
> GPIO58_LCD_LDD_0, \
> diff -uprN clean-3.0.1/drivers/input/mouse/Kconfig
> linux-3.0.1/drivers/input/mouse/Kconfig ---
> clean-3.0.1/drivers/input/mouse/Kconfig 2011-08-05 05:59:21.000000000
> +0100 +++ linux-3.0.1/drivers/input/mouse/Kconfig 2011-08-11
> 16:49:00.004450942 +0100 @@ -322,4 +322,14 @@ config MOUSE_SYNAPTICS_I2C
> To compile this driver as a module, choose M here: the
> module will be called synaptics_i2c.
>
> +config MOUSE_NAVPOINT_PXA27x
> + bool "Synaptics NavPoint (PXA27x SSP/SPI)"
> + depends on PXA27x && PXA_SSP
> + help
> + This option enables support for the Synaptics NavPoint connected to
> + a PXA27x SSP port in SPI slave mode. The driver implements a simple
> + navigation pad. The four raised dots are mapped to UP/DOWN/LEFT/RIGHT
> + buttons and the centre of the touchpad is mapped to the ENTER button.
> + Say Y to enable the Synaptics NavPoint on the HP iPAQ hx4700.
> +
> endif
> diff -uprN clean-3.0.1/drivers/input/mouse/Makefile
> linux-3.0.1/drivers/input/mouse/Makefile ---
> clean-3.0.1/drivers/input/mouse/Makefile 2011-08-05 05:59:21.000000000
> +0100 +++ linux-3.0.1/drivers/input/mouse/Makefile 2011-08-11
> 16:49:00.004450942 +0100 @@ -19,6 +19,7 @@ obj-$(CONFIG_MOUSE_RISCPC) +=
> rpcmouse.
> obj-$(CONFIG_MOUSE_SERIAL) += sermouse.o
> obj-$(CONFIG_MOUSE_SYNAPTICS_I2C) += synaptics_i2c.o
> obj-$(CONFIG_MOUSE_VSXXXAA) += vsxxxaa.o
> +obj-$(CONFIG_MOUSE_NAVPOINT_PXA27x) += navpoint.o
Keep the list sorted
>
> psmouse-objs := psmouse-base.o synaptics.o
>
> diff -uprN clean-3.0.1/drivers/input/mouse/navpoint.c
> linux-3.0.1/drivers/input/mouse/navpoint.c ---
> clean-3.0.1/drivers/input/mouse/navpoint.c 1970-01-01 01:00:00.000000000
> +0100 +++ linux-3.0.1/drivers/input/mouse/navpoint.c 2011-08-11
> 16:50:35.093084330 +0100 @@ -0,0 +1,317 @@
> +/*
> + * Copyright (C) 2011 Paul Parsons <lost.distance at yahoo.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/platform_device.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/gpio.h>
> +#include <linux/input.h>
> +#include <linux/input/navpoint.h>
> +#include <linux/interrupt.h>
> +#include <linux/pxa2xx_ssp.h>
> +#include <linux/slab.h>
> +
> +/*
> + * Synaptics NavPoint (PXA27x SSP/SPI) driver.
> + */
> +
> +struct driver_data {
> + struct ssp_device *ssp;
> + int gpio;
> + struct input_dev *input;
> + int index;
> + uint8_t data[8];
> + int pressed; /* 1 = pressed, 0 = released */
> + unsigned code; /* Key code of the last key pressed */
> +};
Use tabs for alignment please.
> +
> +static const u32 sscr0 = 0
> + | SSCR0_TUM /* TIM = 1; No TUR interrupts */
> + | SSCR0_RIM /* RIM = 1; No ROR interrupts */
> + | SSCR0_SSE /* SSE = 1; SSP enabled */
> + | SSCR0_Motorola /* FRF = 0; Motorola SPI */
> + | SSCR0_DataSize(16) /* DSS = 15; Data size = 16-bit */
> + ;
> +static const u32 sscr1 = 0
> + | SSCR1_SCFR /* SCFR = 1; SSPSCLK only during transfers */
> + | SSCR1_SCLKDIR /* SCLKDIR = 1; Slave mode */
> + | SSCR1_SFRMDIR /* SFRMDIR = 1; Slave mode */
> + | SSCR1_RWOT /* RWOT = 1; Receive without transmit mode */
> + | SSCR1_RxTresh(1) /* RFT = 0; Receive FIFO threshold = 1 */
> + | SSCR1_SPH /* SPH = 1; SSPSCLK inactive 0.5 + 1 cycles */
> + | SSCR1_RIE /* RIE = 1; Receive FIFO interrupt enabled */
> + ;
> +static const u32 sssr = 0
> + | SSSR_BCE /* BCE = 1; Clear BCE */
> + | SSSR_TUR /* TUR = 1; Clear TUR */
> + | SSSR_EOC /* EOC = 1; Clear EOC */
> + | SSSR_TINT /* TINT = 1; Clear TINT */
> + | SSSR_PINT /* PINT = 1; Clear PINT */
> + | SSSR_ROR /* ROR = 1; Clear ROR */
> + ;
> +
> +/*
> + * MEP Query $22: Touchpad Coordinate Range Query is not supported by
> + * the NavPoint module, so sampled values provide the N/S/E/W limits.
> + */
> +
> +#define WEST 2416 /* 1/3 width */
> +#define EAST 3904 /* 2/3 width */
> +#define SOUTH 2480 /* 1/3 height */
> +#define NORTH 3424 /* 2/3 height */
Can't we calibrate this instead of having this hardcoded ? Or use sysfs
attributes / module params ?
> +
> +static void navpoint_packet(void *dev)
> +{
> + struct driver_data *drv_data;
> + int pressed;
> + unsigned x, y;
> + unsigned code;
> +
> + drv_data = dev;
> +
> + switch (drv_data->data[0]) {
> + case 0xff: /* Garbage (packet?) between reset and Hello packet */
> + case 0x00: /* Module 0, NULL packet */
> + break;
> + case 0x0e: /* Module 0, Absolute packet */
> + pressed = (drv_data->data[1] & 0x01);
> + if ((drv_data->pressed ^ pressed) == 0) /* No change */
> + break;
> + drv_data->pressed = pressed;
> + x = ((drv_data->data[2] & 0x1f) << 8) | drv_data->data[3];
> + y = ((drv_data->data[4] & 0x1f) << 8) | drv_data->data[5];
> + if (x < WEST)
> + code = KEY_LEFT;
> + else if (x > EAST)
> + code = KEY_RIGHT;
> + else if (y < SOUTH)
> + code = KEY_DOWN;
> + else if (y > NORTH)
> + code = KEY_UP;
> + else
> + code = KEY_ENTER;
> + if (pressed)
> + drv_data->code = code;
> + input_report_key(drv_data->input, drv_data->code, pressed);
> + input_sync(drv_data->input);
> + break;
> + case 0x19: /* Module 0, Hello packet */
> + if ((drv_data->data[1] & 0xf0) == 0x10)
> + break;
> + /* FALLTHROUGH */
> + default:
> + dev_warn(dev, "spurious packet: 0x%02x,0x%02x,...\n",
> + drv_data->data[0],
> + drv_data->data[1]);
> + break;
> + }
> +
> + drv_data->index = 0;
> +}
> +
> +static irqreturn_t navpoint_int(int irq, void *dev)
> +{
> + struct driver_data *drv_data;
> + struct ssp_device *ssp;
> + u32 status;
> + irqreturn_t ret;
> +
> + drv_data = dev;
> + ssp = drv_data->ssp;
> +
> + status = pxa_ssp_read_reg(ssp, SSSR);
> + ret = (status & (sssr | SSSR_RFS)) ? IRQ_HANDLED : IRQ_NONE;
Please avoid ternary ops.
> +
> + if (status & sssr) {
> + dev_warn(dev, "spurious interrupt: 0x%02x\n", status);
> + pxa_ssp_write_reg(ssp, SSSR, (status & sssr));
> + }
> +
> + while (status & SSSR_RNE) {
> + u32 data;
> +
> + data = pxa_ssp_read_reg(ssp, SSDR);
> + drv_data->data[drv_data->index + 0] = (data >> 8);
> + drv_data->data[drv_data->index + 1] = data;
> + drv_data->index += 2;
> + if ((drv_data->data[0] & 0x07) < drv_data->index)
Maybe document magic numbers?
> + navpoint_packet(dev);
> + status = pxa_ssp_read_reg(ssp, SSSR);
> + }
> +
> + return ret;
> +}
> +
> +#ifdef CONFIG_SUSPEND
> +int navpoint_suspend(struct device *dev)
> +{
> + struct driver_data *drv_data;
> + struct ssp_device *ssp;
> +
> + drv_data = dev_get_drvdata(dev);
> + ssp = drv_data->ssp;
> +
> + if (drv_data->gpio)
> + gpio_set_value(drv_data->gpio, 0);
> +
> + pxa_ssp_write_reg(ssp, SSCR0, 0);
> +
> + clk_disable(ssp->clk);
> +
> + return 0;
> +}
> +
> +int navpoint_resume(struct device *dev)
> +{
> + struct driver_data *drv_data;
> + struct ssp_device *ssp;
> +
> + drv_data = dev_get_drvdata(dev);
> + ssp = drv_data->ssp;
> +
> + clk_enable(ssp->clk);
> +
> + pxa_ssp_write_reg(ssp, SSCR1, sscr1);
> + pxa_ssp_write_reg(ssp, SSSR, sssr);
> + pxa_ssp_write_reg(ssp, SSTO, 0);
> + pxa_ssp_write_reg(ssp, SSCR0, sscr0); /* SSCR0_SSE written last */
> +
> + if (drv_data->gpio)
> + gpio_set_value(drv_data->gpio, 1);
> +
> + /* Wait until SSP port is ready for slave clock operations */
> + while (pxa_ssp_read_reg(ssp, SSSR) & SSSR_CSS)
> + msleep(1);
> +
> + return 0;
> +}
> +
> +static const struct dev_pm_ops navpoint_pm_ops = {
> + .suspend = navpoint_suspend,
> + .resume = navpoint_resume,
> +};
> +#endif
> +
> +static int __devinit navpoint_probe(struct platform_device *pdev)
> +{
> + struct navpoint_platform_data *pdata = pdev->dev.platform_data;
> + int ret;
> + struct driver_data *drv_data;
> + struct ssp_device *ssp;
> + struct input_dev *input;
> +
> + drv_data = kzalloc(sizeof(struct driver_data), GFP_KERNEL);
> + if (!drv_data) {
> + ret = -ENOMEM;
> + goto ret0;
> + }
> +
> + ssp = pxa_ssp_request(pdata->port, pdev->name);
> + if (!ssp) {
> + ret = -ENODEV;
> + goto ret1;
> + }
> +
> + ret = request_irq(ssp->irq, navpoint_int, 0, pdev->name, drv_data);
> + if (ret)
> + goto ret2;
> +
> + input = input_allocate_device();
> + if (!input) {
> + ret = -ENOMEM;
> + goto ret3;
> + }
> + input->name = pdev->name;
> + __set_bit(EV_KEY, input->evbit);
> + __set_bit(KEY_ENTER, input->keybit);
> + __set_bit(KEY_UP, input->keybit);
> + __set_bit(KEY_LEFT, input->keybit);
> + __set_bit(KEY_RIGHT, input->keybit);
> + __set_bit(KEY_DOWN, input->keybit);
> + input->dev.parent = &pdev->dev;
> + ret = input_register_device(input);
> + if (ret)
> + goto ret4;
> +
> + drv_data->ssp = ssp;
> + drv_data->gpio = pdata->gpio;
> + drv_data->input = input;
> +
> + platform_set_drvdata(pdev, drv_data);
> +
> + (void) navpoint_resume(&pdev->dev);
> +
> + dev_info(&pdev->dev, "ssp%d, irq %d\n", pdata->port, ssp->irq);
> +
> + return 0;
> +
> +ret4:
> + input_free_device(input);
> +ret3:
> + free_irq(ssp->irq, drv_data);
> +ret2:
> + pxa_ssp_free(ssp);
> +ret1:
> + kfree(drv_data);
> +ret0:
> + return ret;
> +}
> +
> +static int __devexit navpoint_remove(struct platform_device *pdev)
> +{
> + struct driver_data *drv_data;
> + struct ssp_device *ssp;
> + struct input_dev *input;
> +
> + drv_data = platform_get_drvdata(pdev);
> + ssp = drv_data->ssp;
> + input = drv_data->input;
> +
> + (void) navpoint_suspend(&pdev->dev);
> +
> + input_unregister_device(input);
> +
> + free_irq(ssp->irq, drv_data);
> +
> + pxa_ssp_free(ssp);
> +
> + kfree(drv_data);
> +
> + return 0;
> +}
> +
> +static struct platform_driver navpoint_driver = {
> + .probe = navpoint_probe,
> + .remove = __devexit_p(navpoint_remove),
> + .driver = {
> + .name = "navpoint",
> + .owner = THIS_MODULE,
> +#ifdef CONFIG_SUSPEND
> + .pm = &navpoint_pm_ops,
> +#endif
> + },
> +};
> +
> +static int __init navpoint_init(void)
> +{
> + return platform_driver_register(&navpoint_driver);
> +}
> +
> +static void __exit navpoint_exit(void)
> +{
> + platform_driver_unregister(&navpoint_driver);
> +}
> +
> +module_init(navpoint_init);
> +module_exit(navpoint_exit);
> +
> +MODULE_AUTHOR("Paul Parsons <lost.distance at yahoo.com>");
> +MODULE_DESCRIPTION("Synaptics NavPoint (PXA27x SSP/SPI) driver");
> +MODULE_LICENSE("GPL");
Isn't the original authors credit missing here and/or in the header?
> diff -uprN clean-3.0.1/include/linux/input/navpoint.h
> linux-3.0.1/include/linux/input/navpoint.h ---
> clean-3.0.1/include/linux/input/navpoint.h 1970-01-01 01:00:00.000000000
> +0100 +++ linux-3.0.1/include/linux/input/navpoint.h 2011-08-11
> 16:50:50.761188696 +0100 @@ -0,0 +1,12 @@
> +/*
> + * Copyright (C) 2011 Paul Parsons <lost.distance at yahoo.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +struct navpoint_platform_data {
> + int port; /* PXA SSP port for pxa_ssp_request() */
> + int gpio; /* GPIO for power on/off */
> +};
Cheers!
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
More information about the linux-arm-kernel
mailing list