[PATCH 4/5 V2] ARM: tegra: paz00: add clocks requiredforusboperation

[Marc Dietich]

> On Wed, Aug 10, 2011 at 3:50 AM, Marc Dietich <marvin24 at gmx.de> wrote:
> >> > Marc Dietrich wrote at Tuesday, August 09, 2011 1:26 PM:
> >> > > On Tuesday 09 August 2011 20:35:45 you wrote:
> >> > > > [...]
> >> > > > Do you need the pll_p_out4 entry? What's that driving? Check in
> >> > > > /sys/kernel/debug/clock/clock_tree (/sys/kernel/debug is debugfs).
> >> > > 
> >> > > I think it is only required to setup the correct (non-standard?)
> >> > > frequency. Seems all other boards use 108 MHz which cause one of the
> >> > > ports to fail. Don't ask me for details ...
> >> > 
> >> > ...
> >> > 
> >> > > root at ac100:~# cat /sys/kernel/debug/clock/clock_tree
> >> > > 
> >> > >    clock                          state  ref div      rate
> >> > > 
> >> > > --------------------------------------------------------------
> >> > > 
> >> > >    clk_m                          on     9            12000000
> >> > 
> >> > ...
> >> > 
> >> > >       pll_p                       on     10  x18      216000000
> >> > 
> >> > ...
> >> > 
> >> > >          pll_p_out4               on     3   9        24000000
> >> > > 
> >> > >             sclk                  on     2            24000000
> >> > > 
> >> > >                avp.sclk           off    0            24000000
> >> > >                cop                on     1            24000000
> >> > >                hclk               on     2   1        24000000
> >> > > 
> >> > >                   pclk            on     2   2        12000000
> >> > > 
> >> > >                      apbdma       on     1   1        12000000
> >> > 
> >> > Hmm. That's pretty odd.
> >> > 
> >> > With the standard kernel the device ships with, what does the clock
> >> > tree under pll_p_out4 look like? It'd be very interesting to compare
> >> > that. If that setup is the same as what this patch sets up, the patch
> >> > seems fine.
> >> 
> >> unfortunately, there is no such think in .32 kernel (the kernel deliverd
> >> with the device), and I don't think I can port it over.
> >> 
> >> > As far as I know all the clocks there are both unrelated to USB, and
> >> > internal to the device, so the board shouldn't have any effect. In
> >> > particular, avp.sclk/cop are for the internal media CPU/DSP, hclk/pclk
> >> > are the internal AHB/APB bus clocks, and apbdma is for an internal DMA
> >> > engine, currently only used for audio in the mainline kernel at least.
> >> 
> >> Does this mean that the internal busses you mentioned are also running
> >> at low speed? Would this be a hugh performance penality?
> > 
> > maybe this is why in the commit mentioned below sclk is bind to
> > pll_c_out1 and set to 108 MHz again.
> > 
> > But I cannot see this change in the current seaboard clock table
> > (optimized away?). Maybe someone with a seaboard could check this.
> 
> We moved some of this to common.c, and should be posting those patches
> in a while. It doesn't make sense to run sclk on pll_m, since that one
> scales with memory clock scaling.

Olof,

ok, I see. In .38 sclk is bound to pll_c_out1 running at 120 MHz. So we need no 
further change, just wait for the patch to arrive.

Thanks!

Marc