[PATCH v2 3/4] eukrea_mbimx27: add audio codec

[Sascha Hauer]

Hi Eric,

The patch does not apply on current master. Can you please rebase it?
It's better we delay the defconfig patch until the code is merged, so
give me a ping when it's done.

Two comments inline.

Sascha

On Thu, May 27, 2010 at 10:58:56AM +0200, Eric Bénard wrote:
> Signed-off-by: Eric Bénard <eric at eukrea.com>
> Cc: Sascha Hauer <s.hauer at pengutronix.de>
> Cc: Mark Brown <broonie at opensource.wolfsonmicro.com>
> Cc: Liam Girdwood <lrg at slimlogic.co.uk>
> ---
>  arch/arm/mach-mx2/eukrea_mbimx27-baseboard.c |   44 +++++++++++++++++++++++++-
>  1 files changed, 43 insertions(+), 1 deletions(-)
> 
> diff --git a/arch/arm/mach-mx2/eukrea_mbimx27-baseboard.c b/arch/arm/mach-mx2/eukrea_mbimx27-baseboard.c
> index 9038e1f..e7fd65a 100644
> --- a/arch/arm/mach-mx2/eukrea_mbimx27-baseboard.c
> +++ b/arch/arm/mach-mx2/eukrea_mbimx27-baseboard.c
> @@ -1,5 +1,5 @@
>  /*
> - * Copyright (C) 2009 Eric Benard - eric at eukrea.com
> + * Copyright (C) 2009-2010 Eric Benard - eric at eukrea.com
>   *
>   * Based on pcm970-baseboard.c which is :
>   * Copyright (C) 2008 Juergen Beisert (kernel at pengutronix.de)
> @@ -37,6 +37,8 @@
>  #include <mach/mmc.h>
>  #include <mach/imx-uart.h>
>  #include <mach/spi.h>
> +#include <mach/ssi.h>
> +#include <mach/audmux.h>
>  
>  #include "devices.h"
>  
> @@ -93,6 +95,13 @@ static int eukrea_mbimx27_pins[] = {
>  	PD29_PF_CSPI1_SCLK,
>  	PD30_PF_CSPI1_MISO,
>  	PD31_PF_CSPI1_MOSI,
> +	/* SSI4 */
> +#if defined(CONFIG_SND_SOC_EUKREA_TLV320)
> +	PC16_PF_SSI4_FS,
> +	PC17_PF_SSI4_RXD | GPIO_PUEN,
> +	PC18_PF_SSI4_TXD | GPIO_PUEN,
> +	PC19_PF_SSI4_CLK,
> +#endif

You should remove the ifdefs. The pin muxer should not depend on compile
time options.

>  };
>  
>  static const uint32_t eukrea_mbimx27_keymap[] = {
> @@ -292,6 +301,12 @@ static struct spi_board_info eukrea_mbimx27_spi_board_info[] __initdata = {
>  	},
>  };
>  
> +static struct i2c_board_info eukrea_mbimx27_i2c_devices[] = {
> +	{
> +		I2C_BOARD_INFO("tlv320aic23", 0x1a),
> +	},
> +};
> +
>  static int eukrea_mbimx27_spi_cs[] = {GPIO_PORTD | 28};
>  
>  static struct spi_imx_master eukrea_mbimx27_spi_0_data = {
> @@ -308,6 +323,10 @@ static struct imxmmc_platform_data sdhc_pdata = {
>  	.dat3_card_detect = 1,
>  };
>  
> +struct imx_ssi_platform_data eukrea_mbimx27_ssi_pdata = {
> +	.flags = IMX_SSI_DMA | IMX_SSI_USE_I2S_SLAVE,
> +};
> +
>  /*
>   * system init for baseboard usage. Will be called by cpuimx27 init.
>   *
> @@ -319,6 +338,24 @@ void __init eukrea_mbimx27_baseboard_init(void)
>  	mxc_gpio_setup_multiple_pins(eukrea_mbimx27_pins,
>  		ARRAY_SIZE(eukrea_mbimx27_pins), "MBIMX27");
>  
> +#if defined(CONFIG_SND_SOC_EUKREA_TLV320)
> +	/* SSI unit master I2S codec connected to SSI_PINS_4*/
> +	mxc_audmux_v1_configure_port(MX27_AUDMUX_HPCR1_SSI0,
> +			MXC_AUDMUX_V1_PCR_SYN |
> +			MXC_AUDMUX_V1_PCR_TFSDIR |
> +			MXC_AUDMUX_V1_PCR_TCLKDIR |
> +			MXC_AUDMUX_V1_PCR_RFSDIR |
> +			MXC_AUDMUX_V1_PCR_RCLKDIR |
> +			MXC_AUDMUX_V1_PCR_TFCSEL(MX27_AUDMUX_HPCR3_SSI_PINS_4) |
> +			MXC_AUDMUX_V1_PCR_RFCSEL(MX27_AUDMUX_HPCR3_SSI_PINS_4) |
> +			MXC_AUDMUX_V1_PCR_RXDSEL(MX27_AUDMUX_HPCR3_SSI_PINS_4)
> +	);
> +	mxc_audmux_v1_configure_port(MX27_AUDMUX_HPCR3_SSI_PINS_4,
> +			MXC_AUDMUX_V1_PCR_SYN |
> +			MXC_AUDMUX_V1_PCR_RXDSEL(MX27_AUDMUX_HPCR1_SSI0)
> +	);
> +#endif

Does it hurt to go without the ifdefs?

> +
>  	mxc_register_device(&mxc_uart_device1, &uart_pdata[0]);
>  	mxc_register_device(&mxc_uart_device2, &uart_pdata[1]);
>  #if !defined(MACH_EUKREA_CPUIMX27_USEUART4)
> @@ -328,6 +365,11 @@ void __init eukrea_mbimx27_baseboard_init(void)
>  	mxc_register_device(&mxc_fb_device, &eukrea_mbimx27_fb_data);
>  	mxc_register_device(&mxc_sdhc_device0, &sdhc_pdata);
>  
> +	i2c_register_board_info(0, eukrea_mbimx27_i2c_devices,
> +				ARRAY_SIZE(eukrea_mbimx27_i2c_devices));
> +
> +	mxc_register_device(&imx_ssi_device0, &eukrea_mbimx27_ssi_pdata);
> +
>  #if defined(CONFIG_TOUCHSCREEN_ADS7846) \
>  	|| defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
>  	/* ADS7846 Touchscreen controller init */
> -- 
> 1.6.3.3
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |