[PATCH 1/1] ehci-mxc: Fix mx31 OTG host initialisation

[Sascha Hauer]

On Mon, May 10, 2010 at 08:13:40PM +0200, Philippe Rétornaz wrote:
> On mx31 the OTG host initialisation fail if you need to have
> an ULPI transfert to initialize the PHY.
> 
> In order to be able to communicate with the PHY a complete reset
> of the usb host is needed. After the PHY initialization the host
> usb configuration registers need to be rewritten to avoid a host
> controller lockup.
> 
> Signed-off-by: Philippe Rétornaz <philippe.retornaz at epfl.ch>
> ---
>  drivers/usb/host/ehci-mxc.c |   68 +++++++++++++++++++++++++++++++++++++++++++
>  1 files changed, 68 insertions(+), 0 deletions(-)
> 
> diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
> index 544ccfd..39d28da 100644
> --- a/drivers/usb/host/ehci-mxc.c
> +++ b/drivers/usb/host/ehci-mxc.c
> @@ -29,6 +29,11 @@
>  #define PORTSC_OFFSET		0x184
>  #define USBMODE_OFFSET		0x1a8
>  #define USBMODE_CM_HOST		3
> +#define USBCMD_OFFSET		0x140
> +#define USBCMD_RS		(1 << 0)
> +#define USBCMD_RST		(1 << 1)
> +#define USBSTS_OFFSET		0x144
> +#define USBSTS_HCH		(1 << 12)
>  
>  struct ehci_mxc_priv {
>  	struct clk *usbclk, *ahbclk;
> @@ -120,6 +125,7 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
>  	int irq, ret, temp;
>  	struct ehci_mxc_priv *priv;
>  	struct device *dev = &pdev->dev;
> +	int i;
>  
>  	dev_info(&pdev->dev, "initializing i.MX USB Controller\n");
>  
> @@ -204,6 +210,51 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
>  	if (ret < 0)
>  		goto err_init;
>  
> +	/* i.Mx31 OTG host has a bug, if you don't do a reset, then ULPI
> +	 * transfert timeout. */

s/transfert/transfers/
Same below.

> +	if (cpu_is_mx31() && pdev->id == 0) {
> +		/* Wait for the controller to go idle */
> +		for (i = 0; i < 10000; i++) {
> +			if (readl(hcd->regs + USBSTS_OFFSET) & USBSTS_HCH)
> +				break;
> +			udelay(1);
> +		}
> +		if (i == 10000) {
> +			dev_err(dev, "Timeout while stopping USB controller\n");
> +			goto err_init;
> +		}
> +
> +		/* Stop the usb controller */
> +		temp = readl(hcd->regs + USBCMD_OFFSET);
> +		writel(temp & (~USBCMD_RS), hcd->regs + USBCMD_OFFSET);
> +
> +		for (i = 0; i < 10000; i++) {
> +			if (!(readl(hcd->regs + USBCMD_OFFSET) & USBCMD_RS))
> +				break;
> +			udelay(1);
> +		}
> +
> +		if (i == 10000) {
> +			dev_err(dev, "Timeout while stopping USB controller\n");
> +			goto err_init;
> +		}
> +
> +		/* Reset the usb controller */
> +		temp = readl(hcd->regs + USBCMD_OFFSET);
> +		writel(temp | USBCMD_RST, hcd->regs + USBCMD_OFFSET);
> +
> +		for (i = 0; i < 10000; i++) {
> +			if (!(readl(hcd->regs + USBCMD_OFFSET) & USBCMD_RST))
> +				break;
> +			udelay(1);
> +		}
> +
> +		if (i == 10000) {
> +			dev_err(dev, "Timeout while reseting USB controller\n");
> +			goto err_init;
> +		}
> +	}

You add the resetting of the controller after setting up USBMODE/PORTSC
setup. Wouldn't it be possible to change the order so that we do not
have to do it twice?
Also, I think the whole reset functionality should be a seperate
function. I can imagine we'll need it elsewhere or on different SoCs in
which case the if clause above gets complicated.

Sascha


> +
>  	/* Initialize the transceiver */
>  	if (pdata->otg) {
>  		pdata->otg->io_priv = hcd->regs + ULPI_VIEWPORT_OFFSET;
> @@ -213,6 +264,23 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
>  			dev_err(dev, "unable to enable vbus on transceiver\n");
>  	}
>  
> +	/* i.Mx31 OTG host has a bug, if you do an ULPI transfert then the host
> +	 * controller stay busy. Rewriting the register is enough to make it
> +	 * working */
> +	if (cpu_is_mx31() && pdev->id == 0) {
> +		/* set USBMODE to host mode */
> +		temp = readl(hcd->regs + USBMODE_OFFSET);
> +		writel(temp | USBMODE_CM_HOST, hcd->regs + USBMODE_OFFSET);
> +
> +		/* set up the PORTSCx register */
> +		writel(pdata->portsc, hcd->regs + PORTSC_OFFSET);
> +
> +		/* setup USBCONTROL. */
> +		ret = mxc_initialize_usb_hw(pdev->id, pdata->flags);
> +		if (ret < 0)
> +			goto err_init;
> +	}
> +
>  	priv->hcd = hcd;
>  	platform_set_drvdata(pdev, priv);
>  
> -- 
> 1.6.3.3
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |