[PATCH] pxa3xx_nand: rework irq logic
Lei Wen
leiwen at marvell.com
Sun Mar 21 23:38:46 EDT 2010
Enable all irq when we start the nand controller, and
put all the transaction logic in the pxa3xx_nand_irq.
By doing this way, we could dramatically increase the
performance by avoid unnecessary delay.
Signed-off-by: Lei Wen <leiwen at marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang at marvell.com>
---
drivers/mtd/nand/pxa3xx_nand.c | 382 +++++++++++++++-------------------------
1 files changed, 140 insertions(+), 242 deletions(-)
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 0ef9bf9..85de7f7 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -27,6 +27,7 @@
#include <plat/pxa3xx_nand.h>
#define CHIP_DELAY_TIMEOUT (2 * HZ/10)
+#define NAND_STOP_DELAY (2 * HZ/50)
/* registers and bit definitions */
#define NDCR (0x00) /* Control register */
@@ -49,6 +50,7 @@
#define NDCR_DWIDTH_M (0x1 << 26)
#define NDCR_PAGE_SZ (0x1 << 24)
#define NDCR_NCSX (0x1 << 23)
+#define NDCR_STOP_ON_UNCOR (0x1 << 22)
#define NDCR_ND_MODE (0x3 << 21)
#define NDCR_NAND_MODE (0x0)
#define NDCR_CLR_PG_CNT (0x1 << 20)
@@ -59,9 +61,11 @@
#define NDCR_RA_START (0x1 << 15)
#define NDCR_PG_PER_BLK (0x1 << 14)
#define NDCR_ND_ARB_EN (0x1 << 12)
+#define NDCR_INT_MASK (0xFFF)
#define NDSR_MASK (0xfff)
-#define NDSR_RDY (0x1 << 11)
+#define NDSR_RDY (0x1 << 12)
+#define NDSR_FLASH_RDY (0x1 << 11)
#define NDSR_CS0_PAGED (0x1 << 10)
#define NDSR_CS1_PAGED (0x1 << 9)
#define NDSR_CS0_CMDD (0x1 << 8)
@@ -104,13 +108,14 @@ enum {
};
enum {
- STATE_READY = 0,
- STATE_CMD_HANDLE,
- STATE_DMA_READING,
- STATE_DMA_WRITING,
- STATE_DMA_DONE,
- STATE_PIO_READING,
- STATE_PIO_WRITING,
+ STATE_CMD_WAIT_DONE = 1,
+ STATE_DATA_PROCESSING = (1 << 1),
+ STATE_DATA_DONE = (1 << 2),
+ STATE_PAGE_DONE = (1 << 3),
+ STATE_CMD_DONE = (1 << 4),
+ STATE_READY = (1 << 5),
+ STATE_CMD_PREPARED = (1 << 6),
+ STATE_IS_WRITE = (1 << 7),
};
struct pxa3xx_nand_timing {
@@ -299,25 +304,6 @@ static void pxa3xx_nand_set_timing(struct
pxa3xx_nand_info *info,
nand_writel(info, NDTR1CS0, ndtr1);
}
-#define WAIT_EVENT_TIMEOUT 10
-
-static int wait_for_event(struct pxa3xx_nand_info *info, uint32_t event)
-{
- int timeout = WAIT_EVENT_TIMEOUT;
- uint32_t ndsr;
-
- while (timeout--) {
- ndsr = nand_readl(info, NDSR) & NDSR_MASK;
- if (ndsr & event) {
- nand_writel(info, NDSR, ndsr);
- return 0;
- }
- udelay(10);
- }
-
- return -ETIMEDOUT;
-}
-
static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info)
{
int oob_enable = info->reg_ndcr & NDCR_SPARE_EN;
@@ -337,7 +323,47 @@ static void pxa3xx_set_datasize(struct
pxa3xx_nand_info *info)
}
}
-static int prepare_read_prog_cmd(struct pxa3xx_nand_info *info,
+/**
+ * NOTE: it is a must to set ND_RUN firstly, then write
+ * command buffer, otherwise, it does not work.
+ * We enable all the interrupt at the same time, and
+ * let pxa3xx_nand_irq to handle all logic.
+ */
+static void pxa3xx_nand_start(struct pxa3xx_nand_info *info)
+{
+ uint32_t ndcr;
+
+ ndcr = info->reg_ndcr;
+ ndcr |= NDCR_ECC_EN;
+ ndcr |= info->use_dma ? NDCR_DMA_EN : NDCR_STOP_ON_UNCOR;
+ ndcr |= NDCR_ND_RUN;
+
+ /* clear status bits and run */
+ nand_writel(info, NDCR, 0);
+ nand_writel(info, NDSR, NDSR_MASK);
+ nand_writel(info, NDCR, ndcr);
+}
+
+static void pxa3xx_nand_stop(struct pxa3xx_nand_info *info)
+{
+ uint32_t ndcr;
+ int timeout = NAND_STOP_DELAY;
+
+ /* wait RUN bit in NDCR become 0 */
+ do {
+ /* clear status bits */
+ nand_writel(info, NDSR, NDSR_MASK);
+ ndcr = nand_readl(info, NDCR);
+ udelay(1);
+ } while ((ndcr & NDCR_ND_RUN) && (timeout -- > 0));
+
+ if (timeout <= 0) {
+ ndcr &= ~(NDCR_ND_RUN);
+ nand_writel(info, NDCR, ndcr);
+ }
+}
+
+static void prepare_read_prog_cmd(struct pxa3xx_nand_info *info,
uint16_t cmd, int column, int page_addr)
{
pxa3xx_set_datasize(info);
@@ -363,21 +389,18 @@ static int prepare_read_prog_cmd(struct
pxa3xx_nand_info *info,
if (cmd == cmdset.program)
info->ndcb0 |= NDCB0_CMD_TYPE(1) | NDCB0_AUTO_RS;
-
- return 0;
}
-static int prepare_erase_cmd(struct pxa3xx_nand_info *info,
+static void prepare_erase_cmd(struct pxa3xx_nand_info *info,
uint16_t cmd, int page_addr)
{
info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0);
info->ndcb0 |= NDCB0_CMD_TYPE(2) | NDCB0_AUTO_RS | NDCB0_ADDR_CYC(3);
info->ndcb1 = page_addr;
info->ndcb2 = 0;
- return 0;
}
-static int prepare_other_cmd(struct pxa3xx_nand_info *info, uint16_t cmd)
+static void prepare_other_cmd(struct pxa3xx_nand_info *info, uint16_t cmd)
{
info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0);
info->ndcb1 = 0;
@@ -392,10 +415,7 @@ static int prepare_other_cmd(struct
pxa3xx_nand_info *info, uint16_t cmd)
} else if (cmd == cmdset.reset || cmd == cmdset.lock ||
cmd == cmdset.unlock) {
info->ndcb0 |= NDCB0_CMD_TYPE(5);
- } else
- return -EINVAL;
-
- return 0;
+ }
}
static void enable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
@@ -414,71 +434,23 @@ static void disable_int(struct pxa3xx_nand_info
*info, uint32_t int_mask)
nand_writel(info, NDCR, ndcr | int_mask);
}
-/* NOTE: it is a must to set ND_RUN firstly, then write command buffer
- * otherwise, it does not work
- */
-static int write_cmd(struct pxa3xx_nand_info *info)
+static void handle_data_pio(struct pxa3xx_nand_info *info)
{
- uint32_t ndcr;
-
- /* clear status bits and run */
- nand_writel(info, NDSR, NDSR_MASK);
-
- ndcr = info->reg_ndcr;
-
- ndcr |= info->use_ecc ? NDCR_ECC_EN : 0;
- ndcr |= info->use_dma ? NDCR_DMA_EN : 0;
- ndcr |= NDCR_ND_RUN;
-
- nand_writel(info, NDCR, ndcr);
-
- if (wait_for_event(info, NDSR_WRCMDREQ)) {
- printk(KERN_ERR "timed out writing command\n");
- return -ETIMEDOUT;
- }
-
- nand_writel(info, NDCB0, info->ndcb0);
- nand_writel(info, NDCB0, info->ndcb1);
- nand_writel(info, NDCB0, info->ndcb2);
- return 0;
-}
-
-static int handle_data_pio(struct pxa3xx_nand_info *info)
-{
- int ret, timeout = CHIP_DELAY_TIMEOUT;
-
- switch (info->state) {
- case STATE_PIO_WRITING:
+ if (info->state & STATE_IS_WRITE) {
__raw_writesl(info->mmio_base + NDDB, info->data_buff,
DIV_ROUND_UP(info->data_size, 4));
if (info->oob_size > 0)
__raw_writesl(info->mmio_base + NDDB, info->oob_buff,
DIV_ROUND_UP(info->oob_size, 4));
- enable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
-
- ret = wait_for_completion_timeout(&info->cmd_complete, timeout);
- if (!ret) {
- printk(KERN_ERR "program command time out\n");
- return -1;
- }
- break;
- case STATE_PIO_READING:
+ }
+ else {
__raw_readsl(info->mmio_base + NDDB, info->data_buff,
DIV_ROUND_UP(info->data_size, 4));
if (info->oob_size > 0)
__raw_readsl(info->mmio_base + NDDB, info->oob_buff,
DIV_ROUND_UP(info->oob_size, 4));
-
- break;
- default:
- printk(KERN_ERR "%s: invalid state %d\n", __func__,
- info->state);
- return -EINVAL;
}
-
- info->state = STATE_READY;
- return 0;
}
static void start_data_dma(struct pxa3xx_nand_info *info, int dir_out)
@@ -514,93 +486,59 @@ static void pxa3xx_nand_data_dma_irq(int
channel, void *data)
if (dcsr & DCSR_BUSERR) {
info->retcode = ERR_DMABUSERR;
- complete(&info->cmd_complete);
}
- if (info->state == STATE_DMA_WRITING) {
- info->state = STATE_DMA_DONE;
- enable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
- } else {
- info->state = STATE_READY;
- complete(&info->cmd_complete);
- }
+ enable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
}
static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
{
struct pxa3xx_nand_info *info = devid;
- unsigned int status;
+ unsigned int status, is_completed = 0;
status = nand_readl(info, NDSR);
- if (status & (NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR)) {
- if (status & NDSR_DBERR)
- info->retcode = ERR_DBERR;
- else if (status & NDSR_SBERR)
- info->retcode = ERR_SBERR;
-
- disable_int(info, NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR);
+ if (status & NDSR_DBERR)
+ info->retcode = ERR_DBERR;
+ if (status & NDSR_SBERR)
+ info->retcode = ERR_SBERR;
+ if (status & (NDSR_RDDREQ | NDSR_WRDREQ)) {
+ info->state |= STATE_DATA_PROCESSING;
+ /* whether use dma to transfer data */
if (info->use_dma) {
- info->state = STATE_DMA_READING;
+ disable_int(info, NDSR_WRDREQ);
start_data_dma(info, 0);
- } else {
- info->state = STATE_PIO_READING;
- complete(&info->cmd_complete);
- }
- } else if (status & NDSR_WRDREQ) {
- disable_int(info, NDSR_WRDREQ);
- if (info->use_dma) {
- info->state = STATE_DMA_WRITING;
- start_data_dma(info, 1);
- } else {
- info->state = STATE_PIO_WRITING;
- complete(&info->cmd_complete);
- }
- } else if (status & (NDSR_CS0_BBD | NDSR_CS0_CMDD)) {
- if (status & NDSR_CS0_BBD)
- info->retcode = ERR_BBERR;
+ goto NORMAL_IRQ_EXIT;
+ } else
+ handle_data_pio(info);
- disable_int(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
- info->state = STATE_READY;
- complete(&info->cmd_complete);
+ info->state |= STATE_DATA_DONE;
}
- nand_writel(info, NDSR, status);
- return IRQ_HANDLED;
-}
-
-static int pxa3xx_nand_do_cmd(struct pxa3xx_nand_info *info, uint32_t event)
-{
- uint32_t ndcr;
- int ret, timeout = CHIP_DELAY_TIMEOUT;
-
- if (write_cmd(info)) {
- info->retcode = ERR_SENDCMD;
- goto fail_stop;
+ if (status & NDSR_CS0_CMDD) {
+ info->state |= STATE_CMD_DONE;
+ is_completed = 1;
}
-
- info->state = STATE_CMD_HANDLE;
-
- enable_int(info, event);
-
- ret = wait_for_completion_timeout(&info->cmd_complete, timeout);
- if (!ret) {
- printk(KERN_ERR "command execution timed out\n");
- info->retcode = ERR_SENDCMD;
- goto fail_stop;
+ if (status & NDSR_FLASH_RDY)
+ info->state |= STATE_READY;
+ if (status & NDSR_CS0_PAGED)
+ info->state |= STATE_PAGE_DONE;
+
+ if (status & NDSR_WRCMDREQ) {
+ nand_writel(info, NDSR, NDSR_WRCMDREQ);
+ status &= ~NDSR_WRCMDREQ;
+ info->state |= STATE_CMD_WAIT_DONE;
+ nand_writel(info, NDCB0, info->ndcb0);
+ nand_writel(info, NDCB0, info->ndcb1);
+ nand_writel(info, NDCB0, info->ndcb2);
}
- if (info->use_dma == 0 && info->data_size > 0)
- if (handle_data_pio(info))
- goto fail_stop;
-
- return 0;
-
-fail_stop:
- ndcr = nand_readl(info, NDCR);
- nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN);
- udelay(10);
- return -ETIMEDOUT;
+ /* clear NDSR to let the controller exit the IRQ */
+ nand_writel(info, NDSR, status);
+ if (is_completed)
+ complete(&info->cmd_complete);
+NORMAL_IRQ_EXIT:
+ return IRQ_HANDLED;
}
static int pxa3xx_nand_dev_ready(struct mtd_info *mtd)
@@ -621,14 +559,12 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info
*mtd, unsigned command,
int column, int page_addr)
{
struct pxa3xx_nand_info *info = mtd->priv;
- int ret;
+ int ret, exec_cmd = 0;
info->use_dma = (use_dma) ? 1 : 0;
info->use_ecc = 0;
info->data_size = 0;
- info->state = STATE_READY;
-
- init_completion(&info->cmd_complete);
+ info->state = 0;
switch (command) {
case NAND_CMD_READOOB:
@@ -637,14 +573,13 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info
*mtd, unsigned command,
info->buf_start = mtd->writesize + column;
memset(info->data_buff, 0xFF, info->buf_count);
- if (prepare_read_prog_cmd(info, cmdset.read1, column, page_addr))
- break;
-
- pxa3xx_nand_do_cmd(info, NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR);
+ prepare_read_prog_cmd(info, cmdset.read1, column, page_addr);
/* We only are OOB, so if the data has error, does not matter */
if (info->retcode == ERR_DBERR)
info->retcode = ERR_NONE;
+
+ exec_cmd = 1;
break;
case NAND_CMD_READ0:
@@ -654,11 +589,7 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info
*mtd, unsigned command,
info->buf_count = mtd->writesize + mtd->oobsize;
memset(info->data_buff, 0xFF, info->buf_count);
- if (prepare_read_prog_cmd(info, cmdset.read1, column, page_addr))
- break;
-
- pxa3xx_nand_do_cmd(info, NDSR_RDDREQ | NDSR_DBERR | NDSR_SBERR);
-
+ prepare_read_prog_cmd(info, cmdset.read1, column, page_addr);
if (info->retcode == ERR_DBERR) {
/* for blank page (all 0xff), HW will calculate its ECC as
* 0, which is different from the ECC information within
@@ -667,6 +598,8 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info
*mtd, unsigned command,
if (is_buf_blank(info->data_buff, mtd->writesize))
info->retcode = ERR_NONE;
}
+
+ exec_cmd = 1;
break;
case NAND_CMD_SEQIN:
info->buf_start = column;
@@ -680,18 +613,14 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info
*mtd, unsigned command,
case NAND_CMD_PAGEPROG:
info->use_ecc = (info->seqin_column >= mtd->writesize) ? 0 : 1;
- if (prepare_read_prog_cmd(info, cmdset.program,
- info->seqin_column, info->seqin_page_addr))
- break;
-
- pxa3xx_nand_do_cmd(info, NDSR_WRDREQ);
+ prepare_read_prog_cmd(info, cmdset.program,
+ info->seqin_column, info->seqin_page_addr);
+ info->state |= STATE_IS_WRITE;
+ exec_cmd = 1;
break;
case NAND_CMD_ERASE1:
- if (prepare_erase_cmd(info, cmdset.erase, page_addr))
- break;
-
- pxa3xx_nand_do_cmd(info, NDSR_CS0_BBD | NDSR_CS0_CMDD);
- break;
+ prepare_erase_cmd(info, cmdset.erase, page_addr);
+ exec_cmd = 1;
case NAND_CMD_ERASE2:
break;
case NAND_CMD_READID:
@@ -701,39 +630,37 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info
*mtd, unsigned command,
info->buf_count = (command == NAND_CMD_READID) ?
info->read_id_bytes : 1;
- if (prepare_other_cmd(info, (command == NAND_CMD_READID) ?
- cmdset.read_id : cmdset.read_status))
- break;
-
- pxa3xx_nand_do_cmd(info, NDSR_RDDREQ);
+ prepare_other_cmd(info, (command == NAND_CMD_READID) ?
+ cmdset.read_id : cmdset.read_status);
+ exec_cmd = 1;
break;
case NAND_CMD_RESET:
- if (prepare_other_cmd(info, cmdset.reset))
- break;
-
- ret = pxa3xx_nand_do_cmd(info, NDSR_CS0_CMDD);
- if (ret == 0) {
- int timeout = 2;
- uint32_t ndcr;
-
- while (timeout--) {
- if (nand_readl(info, NDSR) & NDSR_RDY)
- break;
- msleep(10);
- }
-
- ndcr = nand_readl(info, NDCR);
- nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN);
- }
+ prepare_other_cmd(info, cmdset.reset);
+ exec_cmd = 1;
break;
default:
printk(KERN_ERR "non-supported command.\n");
break;
}
- if (info->retcode == ERR_DBERR) {
- printk(KERN_ERR "double bit error @ page %08x\n", page_addr);
- info->retcode = ERR_NONE;
+ if (exec_cmd) {
+ init_completion(&info->cmd_complete);
+ info->state |= STATE_CMD_PREPARED;
+ pxa3xx_nand_start(info);
+
+ ret = wait_for_completion_timeout(&info->cmd_complete,
+ CHIP_DELAY_TIMEOUT);
+ if (!ret) {
+ printk(KERN_ERR "Wait time out!!!\n");
+ }
+ /* Stop State Machine for next command cycle */
+ pxa3xx_nand_stop(info);
+ disable_int(info, NDCR_INT_MASK);
+ info->state &= ~STATE_CMD_PREPARED;
+ if (info->retcode == ERR_DBERR) {
+ printk(KERN_ERR "double bit error @ page %08x\n", page_addr);
+ info->retcode = ERR_NONE;
+ }
}
}
@@ -842,41 +769,12 @@ static int pxa3xx_nand_ecc_correct(struct mtd_info *mtd,
return 0;
}
-static int __readid(struct pxa3xx_nand_info *info, uint32_t *id)
-{
- uint32_t ndcr;
- uint8_t id_buff[8];
-
- if (prepare_other_cmd(info, cmdset.read_id)) {
- printk(KERN_ERR "failed to prepare command\n");
- return -EINVAL;
- }
-
- /* Send command */
- if (write_cmd(info))
- goto fail_timeout;
-
- /* Wait for CMDDM(command done successfully) */
- if (wait_for_event(info, NDSR_RDDREQ))
- goto fail_timeout;
-
- __raw_readsl(info->mmio_base + NDDB, id_buff, 2);
- *id = id_buff[0] | (id_buff[1] << 8);
- return 0;
-
-fail_timeout:
- ndcr = nand_readl(info, NDCR);
- nand_writel(info, NDCR, ndcr & ~NDCR_ND_RUN);
- udelay(10);
- return -ETIMEDOUT;
-}
-
static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info,
const struct pxa3xx_nand_flash *f)
{
struct platform_device *pdev = info->pdev;
struct pxa3xx_nand_platform_data *pdata = pdev->dev.platform_data;
- uint32_t ndcr = 0x00000FFF; /* disable all interrupts */
+ uint32_t ndcr = 0;
/* calculate flash information */
info->page_size = f->page_size;
@@ -943,8 +841,9 @@ static int pxa3xx_nand_detect_config(struct
pxa3xx_nand_info *info)
info->read_id_bytes = (default_flash.page_size == 2048) ? 4 : 2;
info->reg_ndcr = ndcr;
- if (__readid(info, &id))
- return -ENODEV;
+
+ pxa3xx_nand_cmdfunc(info->mtd, NAND_CMD_READID, 0, 0);
+ id = *((uint16_t *)(info->data_buff));
/* Lookup the flash id */
id = (id >> 8) & 0xff; /* device id is byte 2 */
@@ -991,8 +890,8 @@ static int pxa3xx_nand_detect_flash(struct
pxa3xx_nand_info *info,
f = &builtin_flash_types[0];
pxa3xx_nand_config_flash(info, f);
- if (__readid(info, &id))
- goto fail_detect;
+ pxa3xx_nand_cmdfunc(info->mtd, NAND_CMD_READID, 0, 0);
+ id = *((uint16_t *)(info->data_buff));
for (i = 1; i < ARRAY_SIZE(builtin_flash_types); i++) {
f = &builtin_flash_types[i];
@@ -1006,7 +905,6 @@ static int pxa3xx_nand_detect_flash(struct
pxa3xx_nand_info *info,
dev_warn(&info->pdev->dev,
"failed to detect configured nand flash; found %04x instead of\n",
id);
-fail_detect:
return -ENODEV;
}
@@ -1283,7 +1181,7 @@ static int pxa3xx_nand_suspend(struct
platform_device *pdev, pm_message_t state)
struct pxa3xx_nand_info *info = platform_get_drvdata(pdev);
struct mtd_info *mtd = info->mtd;
- if (info->state != STATE_READY) {
+ if (info->state & STATE_CMD_PREPARED) {
dev_err(&pdev->dev, "driver busy, state = %d\n", info->state);
return -EAGAIN;
}
--
1.5.6.5
More information about the linux-arm-kernel
mailing list