kernel 2.6.22.18 omap qpio
doron
doronsa at gmail.com
Mon Mar 8 04:32:24 EST 2010
Sorry tao all of this code is remarked and not compiled, it for testing.
The problem is that I install the driver and try to set the GPIO or to clear
and I did not see any change
And I see all parameter goes into the kernel ok (GPIO number & value)
Regard doron
-----Original Message-----
From: TAO HU [mailto:tghk48 at motorola.com]
Sent: Monday, March 08, 2010 11:15 AM
To: doron
Cc: TAO HU; linux-arm-kernel at lists.infradead.org
Subject: Re: kernel 2.6.22.18 omap qpio
I assume the error you referred to is as below.
omap_cfg_reg(MUX1_1_GPIO113);
... ...
ret = omap_request_gpio(MUX1_1_GPIO113);
if (ret < 0)
printk(KERN_ERR "SELECT_MUX1_1: can't reserve GPIO:%d
!\n", MUX1_1_GPIO113);
Pls don't be confused by MUX setting and GPIO operation.
Calling GPIO API (omap_request_gpio() etc.) is independent of MUX
setting though they have functional dependency.
It means that the number passed to omap_request_gpio() should be GPIO#
(113 in this case).
So the correct code should be
omap_cfg_reg(MUX1_1_GPIO113);
... ...
ret = omap_request_gpio(113);
On Mon, Mar 8, 2010 at 4:42 PM, doron <doronsa at gmail.com> wrote:
>
> Hi tao
>
> Yes the processor is OMAP 35XX
>
> The code off the driver:
>
>
>
>
>
> #include <linux/kernel.h>
>
> #include <linux/module.h>
>
> #include <linux/fs.h>
>
> #include <asm/uaccess.h>
>
> #include <asm/arch/gpio.h>
>
> //#include <asm/gpio.h>
>
>
>
> #include <asm/arch/omap34xx.h>
>
> #include <asm/arch/hardware.h>
>
>
>
> #include <asm/arch/mux.h>
>
> #include <asm/arch/board.h>
>
> #include <asm/arch/common.h>
>
> #include <asm/arch/keypad.h>
>
> #include <asm/arch/dma.h>
>
> #include <asm/arch/gpmc.h>
>
> #include <asm/arch/twl4030-rtc.h>
>
> #include <asm/arch/mcspi.h>
>
> #include <asm/arch/prcm.h>
>
>
>
>
>
>
>
> static int device_open(struct inode *inode, struct file *file)
>
> {
>
> #ifdef DEBUG
>
> printk(KERN_INFO "device_open(%p)\n", file);
>
> #endif
>
>
>
> return 0;
>
> }
>
>
>
> static int device_release(struct inode *inode, struct file *file)
>
> {
>
> #ifdef DEBUG
>
> printk(KERN_INFO "device_release(%p,%p)\n", inode, file);
>
> #endif
>
>
>
> return 0;
>
> }
>
>
>
> static int device_ioctl(struct inode *inode, struct file *file, unsigned
int ioctl_num, unsigned long ioctl_param)
>
> {
>
> int ret_val = 0;
>
> int ret = 0;
>
> struct pin_value *temp_pin, pv;
>
>
>
> switch(ioctl_num)
>
> {
>
> case IOCTL_CONFIG_PIN_VALUE:
>
>
>
> temp_pin = (struct pin_value*)ioctl_param;
>
>
>
> //if (omap_cfg_reg(temp_pin->pin))
>
> if (omap_request_gpio(temp_pin->pin))
>
> {
>
> omap_free_gpio(temp_pin->pin);
>
> }
>
> else{
>
> printk(KERN_INFO "gpio not config(%lu )\n", temp_pin->pin);
>
> ret_val = -1;
>
> goto ioctl_out;
>
> }
>
> break;
>
> case IOCTL_FREE_PIN_VALUE:
>
>
>
> temp_pin = (struct pin_value*)ioctl_param;
>
>
>
> omap_free_gpio(temp_pin->pin);
>
> printk(KERN_INFO "gpio not free(%lu)\n", temp_pin->pin);
>
> ret_val = -1;
>
> break;
>
> case IOCTL_SET_PIN_VALUE:
>
> temp_pin = (struct pin_value*)ioctl_param;
>
> //printk(KERN_INFO "try to set gpio pin(%lu ) return %d \n",
temp_pin->pin,ret);
>
> omap_request_gpio((int)temp_pin->pin);
>
> omap_set_gpio_direction((int)temp_pin->pin, 0);
//input=1//output=0
>
> if ((int)temp_pin->value)
>
> omap_set_gpio_dataout((int)temp_pin->pin,1);
>
> else
>
> omap_set_gpio_dataout((int)temp_pin->pin,0);
>
>
>
> printk(KERN_INFO "gpio set(%lu ) to val %d\n",
temp_pin->pin,temp_pin->value);
>
> //ret = omap_get_gpio_datain((int)temp_pin->pin);
>
> //printk(KERN_INFO "gpio get (%lu ) to val %d\n",
temp_pin->pin,ret);
>
> omap_free_gpio((int)temp_pin->pin);
>
> ret_val = -1;
>
>
>
> break;
>
> case IOCTL_GET_PIN_VALUE:
>
> temp_pin = (struct pin_value*)ioctl_param;
>
> pv.pin = temp_pin->pin;
>
> /*
>
> omap_get_gpio_datain(int gpio)
>
> Description: This function is responsible for reading pin
values.
>
> Parameter: int gpio - GPIO PIN (Pin 0-63)
>
> */
>
> //omap_free_gpio((int)temp_pin->pin);
>
> if (omap_request_gpio(temp_pin->pin)==0)
>
> {
>
> omap_set_gpio_direction(temp_pin->pin, 1);
//input=1//output=0
>
> pv.value = omap_get_gpio_datain(temp_pin->pin);
>
> printk(KERN_INFO "gpio get val (%lu ) to val %d\n",
temp_pin->pin,pv.value);
>
> if (copy_to_user(temp_pin, &pv, sizeof(struct
pin_value)) != 0)
>
> {
>
> ret_val = -1;
>
> goto ioctl_out;
>
> }
>
> omap_free_gpio((int)temp_pin->pin);
>
> //ret_val = pv.value;
>
> //copy_to_user(temp_pin, &pv, sizeof(struct
pin_value));
>
> }
>
> else{
>
> printk(KERN_INFO "gpio not free(%lu )\n",
temp_pin->pin);
>
> ret_val = -1;
>
> goto ioctl_out;
>
> }
>
> break;
>
> case IOCTL_SET_PIN_INPUT:
>
> temp_pin = (struct pin_value*)ioctl_param;
>
> if (omap_request_gpio(temp_pin->pin)==0)
>
> omap_set_gpio_direction(temp_pin->pin, temp_pin->value);
//input=1//output=0
>
> else{
>
> printk(KERN_INFO "gpio not free(%lu )\n",
temp_pin->pin);
>
> ret_val = -1;
>
> goto ioctl_out;
>
> }
>
> break;
>
>
>
> }
>
>
>
> ioctl_out:
>
> //up(&sw_sem);
>
> return ret_val;
>
> }
>
>
>
>
>
> struct file_operations our_file_ops = {
>
> .ioctl = device_ioctl,
>
> .open = device_open,
>
> .release = device_release,
>
> .owner = THIS_MODULE,
>
> };
>
>
>
> int init_module()
>
> {
>
> int ret_val;
>
>
>
> ret_val = register_chrdev(MAJOR_NUM, DEVICE_NAME, &our_file_ops);
>
>
>
> if (ret_val < 0)
>
> {
>
> printk(KERN_ALERT "device %s failed(%d)\n", DEVICE_NAME, ret_val);
>
> return ret_val;
>
> }
>
>
>
> sema_init(&sw_sem, 1);
>
> printk(KERN_INFO "mknod /dev/%s c %d 0\n", DEVICE_NAME, MAJOR_NUM);
>
> /*
>
> omap_cfg_reg(MUX1_1_GPIO113);
>
> omap_cfg_reg(MUX1_2_GPIO114);
>
> omap_cfg_reg(MUX1_3_GPIO115);
>
>
>
> ret = omap_request_gpio(MUX1_1_GPIO113);
>
> if (ret < 0)
>
> printk(KERN_ERR "SELECT_MUX1_1: can't reserve GPIO:%d !\n",
MUX1_1_GPIO113);
>
> ret = omap_request_gpio(MUX1_2_GPIO114);
>
> if (ret < 0)
>
> printk(KERN_ERR "SELECT_MUX1_2: can't reserve GPIO:%d !\n",
MUX1_2_GPIO114);
>
> ret = omap_request_gpio(MUX1_3_GPIO115);
>
> if (ret < 0)
>
> printk(KERN_ERR "SELECT_MUX1_3: can't reserve GPIO:%d !\n",
MUX1_3_GPIO115);
>
>
>
> */
>
>
>
> return 0;
>
> }
>
>
>
> void cleanup_module()
>
> {
>
> unregister_chrdev(MAJOR_NUM, DEVICE_NAME);
>
> }
>
>
>
>
>
> Regard Doron Sandroy
>
>
>
>
>
> From: TAO HU [mailto:tghk48 at motorola.com]
> Sent: Monday, March 08, 2010 8:45 AM
> To: doron
> Subject: Re: kernel 2.6.22.18 omap qpio
>
>
>
> Are you using OMAP processor?
> Can you post the piece of code so people can help
>
> On Wed, Mar 3, 2010 at 4:25 AM, doron <doronsa at gmail.com> wrote:
>
> Hi all
>
>
>
> I wrote an driver to the activation of " GPIO " according to the kernel
instructions (gpio.txt) and when I request to free the GPIO I receive
always that the GPIO is reserved .
>
> What the required steps in order to toggle the GPIO MUXED and not MUXED
>
>
>
> Regards Doron Sandroy
>
>
>
>
>
>
>
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
>
> --
> Best Regards
> Hu Tao
>
--
Best Regards
Hu Tao
More information about the linux-arm-kernel
mailing list