[PATCH 4/4] pxa/spitz: Rework spitz
Marek Vasut
marek.vasut at gmail.com
Mon Jun 28 08:07:50 EDT 2010
Dne Po 28. června 2010 05:43:12 Eric Miao napsal(a):
> On Thu, Jun 24, 2010 at 10:02 PM, Marek Vasut <marek.vasut at gmail.com> wrote:
> > This huge patch mostly shuffles code. The spitz.c file contained terrible
> > mess and needed a cleanup, here it is:
> >
> > 1) Made every part modular, components are not built in if not selected.
> > 2) Removed loads of preprocessor goo, mostly "#ifdef MACH_AKITA ....
> > #endif" and similar code. The kernel size will grow by a few kb now, but
> > the file is much more readable.
> > 3) Reworked SD/CF power setting function and made it reentrant.
> > 4) Add ISL6271A regulator support
> > 5) Correctly register WM8750
> >
> > Signed-off-by: Marek Vasut <marek.vasut at gmail.com>
>
> I'd prefer to see separate small patches for this?
This is nearly a replacement for the whole file ... maybe we could merge
spitz2.c or something ... or do it this way. I understand your point about
spliting it into smaller chunks, but I don't see a reason in this case.
>
> > ---
> > arch/arm/mach-pxa/include/mach/spitz.h | 2 -
> > arch/arm/mach-pxa/spitz.c | 813
> > ++++++++++++++++++-------------- 2 files changed, 470 insertions(+), 345
> > deletions(-)
> >
> > diff --git a/arch/arm/mach-pxa/include/mach/spitz.h
> > b/arch/arm/mach-pxa/include/mach/spitz.h index fa1998c..685749a 100644
> > --- a/arch/arm/mach-pxa/include/mach/spitz.h
> > +++ b/arch/arm/mach-pxa/include/mach/spitz.h
> > @@ -185,7 +185,5 @@
> > /*
> > * Shared data structures
> > */
> > -extern struct platform_device spitzscoop_device;
> > -extern struct platform_device spitzscoop2_device;
> > extern struct platform_device spitzssp_device;
> > extern struct sharpsl_charger_machinfo spitz_pm_machinfo;
> > diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
> > index c1048a3..fa31980 100644
> > --- a/arch/arm/mach-pxa/spitz.c
> > +++ b/arch/arm/mach-pxa/spitz.c
> > @@ -18,14 +18,15 @@
> > #include <linux/gpio_keys.h>
> > #include <linux/gpio.h>
> > #include <linux/leds.h>
> > -#include <linux/mtd/physmap.h>
> > #include <linux/i2c.h>
> > #include <linux/i2c/pca953x.h>
> > #include <linux/spi/spi.h>
> > #include <linux/spi/ads7846.h>
> > #include <linux/spi/corgi_lcd.h>
> > +#include <linux/mtd/physmap.h>
> > #include <linux/mtd/sharpsl.h>
> > #include <linux/input/matrix_keypad.h>
> > +#include <linux/regulator/machine.h>
> >
> > #include <asm/setup.h>
> > #include <asm/mach-types.h>
> > @@ -33,11 +34,9 @@
> > #include <asm/mach/sharpsl_param.h>
> > #include <asm/hardware/scoop.h>
> >
> > -
> > #include <mach/pxa27x.h>
> > #include <mach/pxa27x-udc.h>
> > #include <mach/reset.h>
> > -#include <plat/i2c.h>
> > #include <mach/irda.h>
> > #include <mach/mmc.h>
> > #include <mach/ohci.h>
> > @@ -45,11 +44,16 @@
> > #include <mach/pxa2xx_spi.h>
> > #include <mach/spitz.h>
> >
> > +#include <plat/i2c.h>
> > +
> > #include "generic.h"
> > #include "devices.h"
> > #include "sharpsl.h"
> >
> > -static unsigned long spitz_pin_config[] __initdata = {
> > +/***********************************************************************
> > ******* + * Pin configuration
> > +
> > ************************************************************************
> > ******/ +static unsigned long sharpslc_pin_config[] __initdata = {
> > /* Chip Selects */
> > GPIO78_nCS_2, /* SCOOP #2 */
> > GPIO79_nCS_3, /* NAND */
> > @@ -124,10 +128,13 @@ static unsigned long spitz_pin_config[] __initdata
> > = { GPIO1_GPIO | WAKEUP_ON_EDGE_FALL, /* SPITZ_GPIO_RESET */ };
> >
> > -/*
> > - * Spitz SCOOP Device #1
> > - */
> > -static struct resource spitz_scoop_resources[] = {
> > +
> > +/***********************************************************************
> > ******* + * Scoop GPIO expander
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_SHARP_SCOOP) ||
> > defined(CONFIG_SHARP_SCOOP_MODULE) +/* SCOOP Device #1 */
> > +static struct resource sharpslc_scoop_1_resources[] = {
> > [0] = {
> > .start = 0x10800000,
> > .end = 0x10800fff,
> > @@ -135,7 +142,7 @@ static struct resource spitz_scoop_resources[] = {
> > },
> > };
> >
> > -static struct scoop_config spitz_scoop_setup = {
> > +static struct scoop_config sharpslc_scoop_1_setup = {
> > .io_dir = SPITZ_SCP_IO_DIR,
> > .io_out = SPITZ_SCP_IO_OUT,
> > .suspend_clr = SPITZ_SCP_SUS_CLR,
> > @@ -143,20 +150,18 @@ static struct scoop_config spitz_scoop_setup = {
> > .gpio_base = SPITZ_SCP_GPIO_BASE,
> > };
> >
> > -struct platform_device spitzscoop_device = {
> > +struct platform_device sharpslc_scoop_1_device = {
> > .name = "sharp-scoop",
> > .id = 0,
> > .dev = {
> > - .platform_data = &spitz_scoop_setup,
> > + .platform_data = &sharpslc_scoop_1_setup,
> > },
> > - .num_resources = ARRAY_SIZE(spitz_scoop_resources),
> > - .resource = spitz_scoop_resources,
> > + .num_resources = ARRAY_SIZE(sharpslc_scoop_1_resources),
> > + .resource = sharpslc_scoop_1_resources,
> > };
> >
> > -/*
> > - * Spitz SCOOP Device #2
> > - */
> > -static struct resource spitz_scoop2_resources[] = {
> > +/* SCOOP Device #2 */
> > +static struct resource sharpslc_scoop_2_resources[] = {
> > [0] = {
> > .start = 0x08800040,
> > .end = 0x08800fff,
> > @@ -164,7 +169,7 @@ static struct resource spitz_scoop2_resources[] = {
> > },
> > };
> >
> > -static struct scoop_config spitz_scoop2_setup = {
> > +static struct scoop_config sharpslc_scoop_2_setup = {
> > .io_dir = SPITZ_SCP2_IO_DIR,
> > .io_out = SPITZ_SCP2_IO_OUT,
> > .suspend_clr = SPITZ_SCP2_SUS_CLR,
> > @@ -172,82 +177,110 @@ static struct scoop_config spitz_scoop2_setup = {
> > .gpio_base = SPITZ_SCP2_GPIO_BASE,
> > };
> >
> > -struct platform_device spitzscoop2_device = {
> > +struct platform_device sharpslc_scoop_2_device = {
> > .name = "sharp-scoop",
> > .id = 1,
> > .dev = {
> > - .platform_data = &spitz_scoop2_setup,
> > + .platform_data = &sharpslc_scoop_2_setup,
> > },
> > - .num_resources = ARRAY_SIZE(spitz_scoop2_resources),
> > - .resource = spitz_scoop2_resources,
> > + .num_resources = ARRAY_SIZE(sharpslc_scoop_2_resources),
> > + .resource = sharpslc_scoop_2_resources,
> > };
> >
> > -#define SPITZ_PWR_SD 0x01
> > -#define SPITZ_PWR_CF 0x02
> > +static void __init sharpslc_scoop_init(void)
> > +{
> > + platform_device_register(&sharpslc_scoop_1_device);
> > +
> > + /* Akita doesn't have the second SCOOP chip */
> > + if (!machine_is_akita())
> > + platform_device_register(&sharpslc_scoop_2_device);
> > +}
> >
> > /* Power control is shared with between one of the CF slots and SD */
> > -static void spitz_card_pwr_ctrl(int device, unsigned short new_cpr)
> > +static void sharpslc_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr)
> > {
> > - unsigned short cpr = read_scoop_reg(&spitzscoop_device.dev,
> > SCOOP_CPR); + unsigned short cpr;
> > + unsigned long flags;
> >
> > - if (new_cpr & 0x0007) {
> > + if (new_cpr & 0x7) {
> > gpio_set_value(SPITZ_GPIO_CF_POWER, 1);
> > - if (!(cpr & 0x0002) && !(cpr & 0x0004))
> > - mdelay(5);
> > - if (device == SPITZ_PWR_CF)
> > - cpr |= 0x0002;
> > - if (device == SPITZ_PWR_SD)
> > - cpr |= 0x0004;
> > - write_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR, cpr |
> > new_cpr); - } else {
> > - if (device == SPITZ_PWR_CF)
> > - cpr &= ~0x0002;
> > - if (device == SPITZ_PWR_SD)
> > - cpr &= ~0x0004;
> > - if (!(cpr & 0x0002) && !(cpr & 0x0004)) {
> > - write_scoop_reg(&spitzscoop_device.dev,
> > SCOOP_CPR, 0x0000); - mdelay(1);
> > - gpio_set_value(SPITZ_GPIO_CF_POWER, 0);
> > - } else {
> > - write_scoop_reg(&spitzscoop_device.dev,
> > SCOOP_CPR, cpr | new_cpr); - }
> > + mdelay(5);
> > + }
> > +
> > + local_irq_save(flags);
> > +
> > + cpr = read_scoop_reg(&sharpslc_scoop_1_device.dev, SCOOP_CPR);
> > +
> > + if (enable & new_cpr)
> > + cpr |= new_cpr;
> > + else
> > + cpr &= ~enable;
> > +
> > + write_scoop_reg(&sharpslc_scoop_1_device.dev, SCOOP_CPR, cpr);
> > +
> > + local_irq_restore(flags);
> > +
> > + if (!(cpr & 0x7)) {
> > + mdelay(1);
> > + gpio_set_value(SPITZ_GPIO_CF_POWER, 0);
> > }
> > }
> >
> > -static void spitz_pcmcia_pwr(struct device *scoop, unsigned short cpr,
> > int nr) +#else
> > +static inline void sharpslc_scoop_init(void) {}
> > +static inline void sharpslc_card_pwr_ctrl(uint8_t enable, uint8_t
> > new_cpr) {} +#endif
> > +
> > +/***********************************************************************
> > ******* + * PCMCIA
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_PCMCIA_PXA2XX) ||
> > defined(CONFIG_PCMCIA_PXA2XX_MODULE) +static void
> > sharpslc_pcmcia_pwr(struct device *scoop, uint16_t cpr, int nr) {
> > /* Only need to override behaviour for slot 0 */
> > if (nr == 0)
> > - spitz_card_pwr_ctrl(SPITZ_PWR_CF, cpr);
> > + sharpslc_card_pwr_ctrl(
> > + cpr & (SCOOP_CPR_CF_3V | SCOOP_CPR_CF_XV), cpr);
> > else
> > write_scoop_reg(scoop, SCOOP_CPR, cpr);
> > }
> >
> > -static struct scoop_pcmcia_dev spitz_pcmcia_scoop[] = {
> > -{
> > - .dev = &spitzscoop_device.dev,
> > - .irq = SPITZ_IRQ_GPIO_CF_IRQ,
> > - .cd_irq = SPITZ_IRQ_GPIO_CF_CD,
> > - .cd_irq_str = "PCMCIA0 CD",
> > -},{
> > - .dev = &spitzscoop2_device.dev,
> > - .irq = SPITZ_IRQ_GPIO_CF2_IRQ,
> > - .cd_irq = -1,
> > -},
> > +static struct scoop_pcmcia_dev sharpslc_pcmcia_scoop[] = {
> > + {
> > + .dev = &sharpslc_scoop_1_device.dev,
> > + .irq = SPITZ_IRQ_GPIO_CF_IRQ,
> > + .cd_irq = SPITZ_IRQ_GPIO_CF_CD,
> > + .cd_irq_str = "PCMCIA0 CD",
> > + }, {
> > + .dev = &sharpslc_scoop_2_device.dev,
> > + .irq = SPITZ_IRQ_GPIO_CF2_IRQ,
> > + .cd_irq = -1,
> > + },
> > };
> >
> > -static struct scoop_pcmcia_config spitz_pcmcia_config = {
> > - .devs = &spitz_pcmcia_scoop[0],
> > - .num_devs = 2,
> > - .power_ctrl = spitz_pcmcia_pwr,
> > +static struct scoop_pcmcia_config sharpslc_pcmcia_config = {
> > + .devs = &sharpslc_pcmcia_scoop[0],
> > + .num_devs = 2,
> > + .power_ctrl = sharpslc_pcmcia_pwr,
> > };
> >
> > -EXPORT_SYMBOL(spitzscoop_device);
> > -EXPORT_SYMBOL(spitzscoop2_device);
> > +static void __init sharpslc_pcmcia_init(void)
> > +{
> > + /* Akita has only one PCMCIA slot used */
> > + if (machine_is_akita())
> > + sharpslc_pcmcia_config.num_devs = 1;
> > +
> > + platform_scoop_config = &sharpslc_pcmcia_config;
> > +}
> > +#else
> > +static inline void sharpslc_pcmcia_init(void) {}
> > +#endif
> > +
> > +/***********************************************************************
> > ******* + * GPIO keyboard
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_KEYBOARD_MATRIX) ||
> > defined(CONFIG_KEYBOARD_MATRIX_MODULE)
> >
> > -/*
> > - * Spitz Keyboard Device
> > - */
> > #define SPITZ_KEY_CALENDAR KEY_F1
> > #define SPITZ_KEY_ADDRESS KEY_F2
> > #define SPITZ_KEY_FN KEY_F3
> > @@ -263,7 +296,7 @@ EXPORT_SYMBOL(spitzscoop2_device);
> > #define SPITZ_KEY_OK KEY_F11
> > #define SPITZ_KEY_MENU KEY_F12
> >
> > -static const uint32_t spitzkbd_keymap[] = {
> > +static const uint32_t sharpslc_keymap[] = {
> > KEY(0, 0, KEY_LEFTCTRL),
> > KEY(0, 1, KEY_1),
> > KEY(0, 2, KEY_3),
> > @@ -330,37 +363,48 @@ static const uint32_t spitzkbd_keymap[] = {
> > KEY(6, 8, KEY_RIGHT),
> > };
> >
> > -static const struct matrix_keymap_data spitzkbd_keymap_data = {
> > - .keymap = spitzkbd_keymap,
> > - .keymap_size = ARRAY_SIZE(spitzkbd_keymap),
> > +static const struct matrix_keymap_data sharpslc_keymap_data = {
> > + .keymap = sharpslc_keymap,
> > + .keymap_size = ARRAY_SIZE(sharpslc_keymap),
> > };
> >
> > -static const uint32_t spitzkbd_row_gpios[] =
> > +static const uint32_t sharpslc_row_gpios[] =
> > { 12, 17, 91, 34, 36, 38, 39 };
> > -static const uint32_t spitzkbd_col_gpios[] =
> > +static const uint32_t sharpslc_col_gpios[] =
> > { 88, 23, 24, 25, 26, 27, 52, 103, 107, 108, 114 };
> >
> > -static struct matrix_keypad_platform_data spitzkbd_pdata = {
> > - .keymap_data = &spitzkbd_keymap_data,
> > - .row_gpios = spitzkbd_row_gpios,
> > - .col_gpios = spitzkbd_col_gpios,
> > - .num_row_gpios = ARRAY_SIZE(spitzkbd_row_gpios),
> > - .num_col_gpios = ARRAY_SIZE(spitzkbd_col_gpios),
> > +static struct matrix_keypad_platform_data sharpslc_mkp_pdata = {
> > + .keymap_data = &sharpslc_keymap_data,
> > + .row_gpios = sharpslc_row_gpios,
> > + .col_gpios = sharpslc_col_gpios,
> > + .num_row_gpios = ARRAY_SIZE(sharpslc_row_gpios),
> > + .num_col_gpios = ARRAY_SIZE(sharpslc_col_gpios),
> > .col_scan_delay_us = 10,
> > .debounce_ms = 10,
> > .wakeup = 1,
> > };
> >
> > -static struct platform_device spitzkbd_device = {
> > +static struct platform_device sharpslc_mkp_device = {
> > .name = "matrix-keypad",
> > .id = -1,
> > .dev = {
> > - .platform_data = &spitzkbd_pdata,
> > + .platform_data = &sharpslc_mkp_pdata,
> > },
> > };
> >
> > +static void __init sharpslc_mkp_init(void)
> > +{
> > + platform_device_register(&sharpslc_mkp_device);
> > +}
> > +#else
> > +static inline void sharpslc_mkp_init(void) {}
> > +#endif
> >
> > -static struct gpio_keys_button spitz_gpio_keys[] = {
> > +/***********************************************************************
> > ******* + * GPIO keys
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_KEYBOARD_GPIO) ||
> > defined(CONFIG_KEYBOARD_GPIO_MODULE) +static struct gpio_keys_button
> > sharpslc_gpio_keys[] = {
> > {
> > .type = EV_PWR,
> > .code = KEY_SUSPEND,
> > @@ -383,27 +427,35 @@ static struct gpio_keys_button spitz_gpio_keys[] =
> > { },
> > };
> >
> > -static struct gpio_keys_platform_data spitz_gpio_keys_platform_data = {
> > - .buttons = spitz_gpio_keys,
> > - .nbuttons = ARRAY_SIZE(spitz_gpio_keys),
> > +static struct gpio_keys_platform_data sharpslc_gpio_keys_platform_data =
> > { + .buttons = sharpslc_gpio_keys,
> > + .nbuttons = ARRAY_SIZE(sharpslc_gpio_keys),
> > };
> >
> > -static struct platform_device spitz_gpio_keys_device = {
> > +static struct platform_device sharpslc_gpio_keys_device = {
> > .name = "gpio-keys",
> > .id = -1,
> > .dev = {
> > - .platform_data = &spitz_gpio_keys_platform_data,
> > + .platform_data = &sharpslc_gpio_keys_platform_data,
> > },
> > };
> >
> > +static void __init sharpslc_keys_init(void)
> > +{
> > + platform_device_register(&sharpslc_gpio_keys_device);
> > +}
> > +#else
> > +static inline void sharpslc_keys_init(void) {}
> > +#endif
> >
> > -/*
> > - * Spitz LEDs
> > - */
> > -static struct gpio_led spitz_gpio_leds[] = {
> > +/***********************************************************************
> > ******* + * LEDs
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_LEDS_GPIO) ||
> > defined(CONFIG_LEDS_GPIO_MODULE) +static struct gpio_led
> > sharpslc_gpio_leds[] = {
> > {
> > .name = "spitz:amber:charge",
> > - .default_trigger = "sharpsl-charge",
> > + .default_trigger = "sharpslc-charge",
> > .gpio = SPITZ_GPIO_LED_ORANGE,
> > },
> > {
> > @@ -413,25 +465,32 @@ static struct gpio_led spitz_gpio_leds[] = {
> > },
> > };
> >
> > -static struct gpio_led_platform_data spitz_gpio_leds_info = {
> > - .leds = spitz_gpio_leds,
> > - .num_leds = ARRAY_SIZE(spitz_gpio_leds),
> > +static struct gpio_led_platform_data sharpslc_gpio_leds_info = {
> > + .leds = sharpslc_gpio_leds,
> > + .num_leds = ARRAY_SIZE(sharpslc_gpio_leds),
> > };
> >
> > -static struct platform_device spitzled_device = {
> > +static struct platform_device sharpslc_led_device = {
> > .name = "leds-gpio",
> > .id = -1,
> > .dev = {
> > - .platform_data = &spitz_gpio_leds_info,
> > + .platform_data = &sharpslc_gpio_leds_info,
> > },
> > };
> >
> > -#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
> > -static struct pxa2xx_spi_master spitz_spi_info = {
> > - .num_chipselect = 3,
> > -};
> > +static void __init sharpslc_leds_init(void)
> > +{
> > + platform_device_register(&sharpslc_led_device);
> > +}
> > +#else
> > +static inline void sharpslc_leds_init(void) {}
> > +#endif
> >
> > -static void spitz_wait_for_hsync(void)
> > +/***********************************************************************
> > ******* + * SSP Devices
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_SPI_PXA2XX) ||
> > defined(CONFIG_SPI_PXA2XX_MODULE) +static void
> > sharpslc_ads7846_wait_for_hsync(void)
> > {
> > while (gpio_get_value(SPITZ_GPIO_HSYNC))
> > cpu_relax();
> > @@ -440,21 +499,21 @@ static void spitz_wait_for_hsync(void)
> > cpu_relax();
> > }
> >
> > -static struct ads7846_platform_data spitz_ads7846_info = {
> > +static struct ads7846_platform_data sharpslc_ads7846_info = {
> > .model = 7846,
> > .vref_delay_usecs = 100,
> > .x_plate_ohms = 419,
> > .y_plate_ohms = 486,
> > .pressure_max = 1024,
> > .gpio_pendown = SPITZ_GPIO_TP_INT,
> > - .wait_for_sync = spitz_wait_for_hsync,
> > + .wait_for_sync = sharpslc_ads7846_wait_for_hsync,
> > };
> >
> > -static struct pxa2xx_spi_chip spitz_ads7846_chip = {
> > +static struct pxa2xx_spi_chip sharpslc_ads7846_chip = {
> > .gpio_cs = SPITZ_GPIO_ADS7846_CS,
> > };
> >
> > -static void spitz_bl_kick_battery(void)
> > +static void sharpslc_bl_kick_battery(void)
> > {
> > void (*kick_batt)(void);
> >
> > @@ -465,93 +524,109 @@ static void spitz_bl_kick_battery(void)
> > }
> > }
> >
> > -static struct corgi_lcd_platform_data spitz_lcdcon_info = {
> > +static struct corgi_lcd_platform_data sharpslc_lcdcon_info = {
> > .init_mode = CORGI_LCD_MODE_VGA,
> > .max_intensity = 0x2f,
> > .default_intensity = 0x1f,
> > .limit_mask = 0x0b,
> > .gpio_backlight_cont = SPITZ_GPIO_BACKLIGHT_CONT,
> > .gpio_backlight_on = SPITZ_GPIO_BACKLIGHT_ON,
> > - .kick_battery = spitz_bl_kick_battery,
> > + .kick_battery = sharpslc_bl_kick_battery,
> > };
> >
> > -static struct pxa2xx_spi_chip spitz_lcdcon_chip = {
> > +static struct pxa2xx_spi_chip sharpslc_lcdcon_chip = {
> > .gpio_cs = SPITZ_GPIO_LCDCON_CS,
> > };
> >
> > -static struct pxa2xx_spi_chip spitz_max1111_chip = {
> > +static struct pxa2xx_spi_chip sharpslc_max1111_chip = {
> > .gpio_cs = SPITZ_GPIO_MAX1111_CS,
> > };
> >
> > -static struct spi_board_info spitz_spi_devices[] = {
> > +static struct spi_board_info sharpslc_spi_devices[] = {
> > {
> > - .modalias = "ads7846",
> > - .max_speed_hz = 1200000,
> > - .bus_num = 2,
> > - .chip_select = 0,
> > - .platform_data = &spitz_ads7846_info,
> > - .controller_data= &spitz_ads7846_chip,
> > - .irq = gpio_to_irq(SPITZ_GPIO_TP_INT),
> > + .modalias = "ads7846",
> > + .max_speed_hz = 1200000,
> > + .bus_num = 2,
> > + .chip_select = 0,
> > + .platform_data = &sharpslc_ads7846_info,
> > + .controller_data = &sharpslc_ads7846_chip,
> > + .irq = gpio_to_irq(SPITZ_GPIO_TP_INT),
> > }, {
> > - .modalias = "corgi-lcd",
> > - .max_speed_hz = 50000,
> > - .bus_num = 2,
> > - .chip_select = 1,
> > - .platform_data = &spitz_lcdcon_info,
> > - .controller_data= &spitz_lcdcon_chip,
> > + .modalias = "corgi-lcd",
> > + .max_speed_hz = 50000,
> > + .bus_num = 2,
> > + .chip_select = 1,
> > + .platform_data = &sharpslc_lcdcon_info,
> > + .controller_data = &sharpslc_lcdcon_chip,
> > }, {
> > - .modalias = "max1111",
> > - .max_speed_hz = 450000,
> > - .bus_num = 2,
> > - .chip_select = 2,
> > - .controller_data= &spitz_max1111_chip,
> > + .modalias = "max1111",
> > + .max_speed_hz = 450000,
> > + .bus_num = 2,
> > + .chip_select = 2,
> > + .controller_data = &sharpslc_max1111_chip,
> > },
> > };
> >
> > -static void __init spitz_init_spi(void)
> > +static struct pxa2xx_spi_master sharpslc_spi_info = {
> > + .num_chipselect = 3,
> > +};
> > +
> > +static void __init sharpslc_spi_init(void)
> > {
> > + struct corgi_lcd_platform_data *lcd_data = &sharpslc_lcdcon_info;
> > +
> > if (machine_is_akita()) {
> > - spitz_lcdcon_info.gpio_backlight_cont =
> > AKITA_GPIO_BACKLIGHT_CONT; -
> > spitz_lcdcon_info.gpio_backlight_on = AKITA_GPIO_BACKLIGHT_ON; +
> > lcd_data->gpio_backlight_cont = AKITA_GPIO_BACKLIGHT_CONT; +
> > lcd_data->gpio_backlight_on = AKITA_GPIO_BACKLIGHT_ON; }
> >
> > - pxa2xx_set_spi_info(2, &spitz_spi_info);
> > - spi_register_board_info(ARRAY_AND_SIZE(spitz_spi_devices));
> > + pxa2xx_set_spi_info(2, &sharpslc_spi_info);
> > + spi_register_board_info(ARRAY_AND_SIZE(sharpslc_spi_devices));
> > }
> > #else
> > -static inline void spitz_init_spi(void) {}
> > +static inline void sharpslc_spi_init(void) {}
> > #endif
> >
> > +/***********************************************************************
> > ******* + * SD/MMC card controller
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
> > /*
> > - * MMC/SD Device
> > - *
> > - * The card detect interrupt isn't debounced so we delay it by 250ms
> > - * to give the card a chance to fully insert/eject.
> > + * NOTE: The card detect interrupt isn't debounced so we delay it by
> > 250ms to + * give the card a chance to fully insert/eject.
> > */
> > -static void spitz_mci_setpower(struct device *dev, unsigned int vdd)
> > +static void sharpslc_mci_setpower(struct device *dev, unsigned int vdd)
> > {
> > struct pxamci_platform_data* p_d = dev->platform_data;
> >
> > - if (( 1 << vdd) & p_d->ocr_mask)
> > - spitz_card_pwr_ctrl(SPITZ_PWR_SD, 0x0004);
> > + if ((1 << vdd) & p_d->ocr_mask)
> > + sharpslc_card_pwr_ctrl(SCOOP_CPR_SD_3V, SCOOP_CPR_SD_3V);
> > else
> > - spitz_card_pwr_ctrl(SPITZ_PWR_SD, 0x0000);
> > + sharpslc_card_pwr_ctrl(SCOOP_CPR_SD_3V, 0x0);
> > }
> >
> > -static struct pxamci_platform_data spitz_mci_platform_data = {
> > +static struct pxamci_platform_data sharpslc_mci_platform_data = {
> > .detect_delay_ms = 250,
> > .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
> > - .setpower = spitz_mci_setpower,
> > + .setpower = sharpslc_mci_setpower,
> > .gpio_card_detect = SPITZ_GPIO_nSD_DETECT,
> > .gpio_card_ro = SPITZ_GPIO_nSD_WP,
> > .gpio_power = -1,
> > };
> >
> > +static void __init sharpslc_mmc_init(void)
> > +{
> > + pxa_set_mci_info(&sharpslc_mci_platform_data);
> > +}
> > +#else
> > +static inline void sharpslc_mmc_init(void) {}
> > +#endif
> >
> > -/*
> > - * USB Host (OHCI)
> > - */
> > -static int spitz_ohci_init(struct device *dev)
> > +/***********************************************************************
> > ******* + * USB Host
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_USB_OHCI_HCD) ||
> > defined(CONFIG_USB_OHCI_HCD_MODULE) +static int
> > sharpslc_ohci_init(struct device *dev)
> > {
> > int err;
> >
> > @@ -559,88 +634,114 @@ static int spitz_ohci_init(struct device *dev)
> > if (err)
> > return err;
> >
> > - /* Only Port 2 is connected
> > - * Setup USB Port 2 Output Control Register
> > - */
> > + /* Only Port 2 is connected, setup USB Port 2 Output Control
> > Register */ UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE |
> > UP2OCR_DMPDE;
> >
> > return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
> > }
> >
> > -static void spitz_ohci_exit(struct device *dev)
> > +static void sharpslc_ohci_exit(struct device *dev)
> > {
> > gpio_free(SPITZ_GPIO_USB_HOST);
> > }
> >
> > -static struct pxaohci_platform_data spitz_ohci_platform_data = {
> > +static struct pxaohci_platform_data sharpslc_ohci_platform_data = {
> > .port_mode = PMM_NPS_MODE,
> > - .init = spitz_ohci_init,
> > - .exit = spitz_ohci_exit,
> > + .init = sharpslc_ohci_init,
> > + .exit = sharpslc_ohci_exit,
> > .flags = ENABLE_PORT_ALL | NO_OC_PROTECTION,
> > .power_budget = 150,
> > };
> >
> > +static void __init sharpslc_uhc_init(void)
> > +{
> > + pxa_set_ohci_info(&sharpslc_ohci_platform_data);
> > +}
> > +#else
> > +static inline void sharpslc_uhc_init(void) {}
> > +#endif
> >
> > -/*
> > - * Irda
> > - */
> > -
> > -static struct pxaficp_platform_data spitz_ficp_platform_data = {
> > -/* .gpio_pwdown is set in spitz_init() and akita_init() accordingly */
> > +/***********************************************************************
> > ******* + * IrDA
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_PXA_FICP) || defined(CONFIG_PXA_FICP_MODULE)
> > +static struct pxaficp_platform_data sharpslc_ficp_platform_data = {
> > .transceiver_cap = IR_SIRMODE | IR_OFF,
> > };
> >
> > +static void __init sharpslc_irda_init(void)
> > +{
> > + if (machine_is_akita())
> > + sharpslc_ficp_platform_data.gpio_pwdown =
> > AKITA_GPIO_IR_ON; + else
> > + sharpslc_ficp_platform_data.gpio_pwdown =
> > SPITZ_GPIO_IR_ON;
> >
> > -/*
> > - * Spitz PXA Framebuffer
> > - */
> > + pxa_set_ficp_info(&sharpslc_ficp_platform_data);
> > +}
> > +#else
> > +static inline void sharpslc_irda_init(void) {}
> > +#endif
> >
> > -static struct pxafb_mode_info spitz_pxafb_modes[] = {
> > -{
> > - .pixclock = 19231,
> > - .xres = 480,
> > - .yres = 640,
> > - .bpp = 16,
> > - .hsync_len = 40,
> > - .left_margin = 46,
> > - .right_margin = 125,
> > - .vsync_len = 3,
> > - .upper_margin = 1,
> > - .lower_margin = 0,
> > - .sync = 0,
> > -},{
> > - .pixclock = 134617,
> > - .xres = 240,
> > - .yres = 320,
> > - .bpp = 16,
> > - .hsync_len = 20,
> > - .left_margin = 20,
> > - .right_margin = 46,
> > - .vsync_len = 2,
> > - .upper_margin = 1,
> > - .lower_margin = 0,
> > - .sync = 0,
> > -},
> > -};
> > -
> > -static struct pxafb_mach_info spitz_pxafb_info = {
> > - .modes = &spitz_pxafb_modes[0],
> > - .num_modes = 2,
> > +/***********************************************************************
> > ******* + * Framebuffer
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
> > +static struct pxafb_mode_info sharpslc_pxafb_modes[] = {
> > + {
> > + .pixclock = 19231,
> > + .xres = 480,
> > + .yres = 640,
> > + .bpp = 16,
> > + .hsync_len = 40,
> > + .left_margin = 46,
> > + .right_margin = 125,
> > + .vsync_len = 3,
> > + .upper_margin = 1,
> > + .lower_margin = 0,
> > + .sync = 0,
> > + }, {
> > + .pixclock = 134617,
> > + .xres = 240,
> > + .yres = 320,
> > + .bpp = 16,
> > + .hsync_len = 20,
> > + .left_margin = 20,
> > + .right_margin = 46,
> > + .vsync_len = 2,
> > + .upper_margin = 1,
> > + .lower_margin = 0,
> > + .sync = 0,
> > + },
> > +};
> > +
> > +static struct pxafb_mach_info sharpslc_pxafb_info = {
> > + .modes = sharpslc_pxafb_modes,
> > + .num_modes = ARRAY_SIZE(sharpslc_pxafb_modes),
> > .fixed_modes = 1,
> > .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_ALTERNATE_MAPPING,
> > };
> >
> > -static struct mtd_partition sharpsl_nand_partitions[] = {
> > +static void __init sharpslc_lcd_init(void)
> > +{
> > + set_pxa_fb_info(&sharpslc_pxafb_info);
> > +}
> > +#else
> > +static inline void sharpslc_lcd_init(void) {}
> > +#endif
> > +
> > +/***********************************************************************
> > ******* + * Framebuffer
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_MTD_NAND_SHARPSL) ||
> > defined(CONFIG_MTD_NAND_SHARPSL_MODULE) +static struct mtd_partition
> > sharpslc_nand_partitions[] = {
> > {
> > .name = "System Area",
> > .offset = 0,
> > .size = 7 * 1024 * 1024,
> > - },
> > - {
> > + }, {
> > .name = "Root Filesystem",
> > .offset = 7 * 1024 * 1024,
> > - },
> > - {
> > + }, {
> > .name = "Home Filesystem",
> > .offset = MTDPART_OFS_APPEND,
> > .size = MTDPART_SIZ_FULL,
> > @@ -649,37 +750,72 @@ static struct mtd_partition
> > sharpsl_nand_partitions[] = {
> >
> > static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
> >
> > -static struct nand_bbt_descr sharpsl_bbt = {
> > - .options = 0,
> > - .offs = 4,
> > - .len = 2,
> > - .pattern = scan_ff_pattern
> > +static struct nand_bbt_descr sharpslc_nand_bbt = {
> > + .options = 0,
> > + .offs = 4,
> > + .len = 2,
> > + .pattern = scan_ff_pattern
> > +};
> > +
> > +static struct nand_ecclayout sharpslc_akita_oobinfo = {
> > + .oobfree = { {0x08, 0x09} },
> > + .eccbytes = 24,
> > + .eccpos = {
> > + 0x05, 0x01, 0x02, 0x03, 0x06, 0x07, 0x15, 0x11,
> > + 0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23,
> > + 0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37,
> > + },
> > };
> >
> > -static struct sharpsl_nand_platform_data sharpsl_nand_platform_data = {
> > - .badblock_pattern = &sharpsl_bbt,
> > - .partitions = sharpsl_nand_partitions,
> > - .nr_partitions = ARRAY_SIZE(sharpsl_nand_partitions),
> > +static struct sharpsl_nand_platform_data sharpslc_nand_pdata = {
> > + .badblock_pattern = &sharpslc_nand_bbt,
> > + .partitions = sharpslc_nand_partitions,
> > + .nr_partitions = ARRAY_SIZE(sharpslc_nand_partitions),
> > };
> >
> > -static struct resource sharpsl_nand_resources[] = {
> > +static struct resource sharpslc_nand_resources[] = {
> > {
> > - .start = 0x0C000000,
> > - .end = 0x0C000FFF,
> > + .start = PXA_CS3_PHYS,
> > + .end = PXA_CS3_PHYS + SZ_4K - 1,
> > .flags = IORESOURCE_MEM,
> > },
> > };
> >
> > -static struct platform_device sharpsl_nand_device = {
> > +static struct platform_device sharpslc_nand_device = {
> > .name = "sharpsl-nand",
> > .id = -1,
> > - .resource = sharpsl_nand_resources,
> > - .num_resources = ARRAY_SIZE(sharpsl_nand_resources),
> > - .dev.platform_data = &sharpsl_nand_platform_data,
> > + .resource = sharpslc_nand_resources,
> > + .num_resources = ARRAY_SIZE(sharpslc_nand_resources),
> > + .dev = {
> > + .platform_data = &sharpslc_nand_pdata,
> > + }
> > };
> >
> > +static void __init sharpslc_nand_init(void)
> > +{
> > + if (machine_is_spitz()) {
> > + sharpslc_nand_partitions[1].size = 5 * 1024 * 1024;
> > + } else if (machine_is_akita()) {
> > + sharpslc_nand_partitions[1].size = 58 * 1024 * 1024;
> > + sharpslc_nand_bbt.len = 1;
> > + sharpslc_nand_pdata.ecc_layout = &sharpslc_akita_oobinfo;
> > + } else if (machine_is_borzoi()) {
> > + sharpslc_nand_partitions[1].size = 32 * 1024 * 1024;
> > + sharpslc_nand_bbt.len = 1;
> > + sharpslc_nand_pdata.ecc_layout = &sharpslc_akita_oobinfo;
> > + }
> > +
> > + platform_device_register(&sharpslc_nand_device);
> > +}
> > +#else
> > +static inline void sharpslc_nand_init(void) {}
> > +#endif
> >
> > -static struct mtd_partition sharpsl_rom_parts[] = {
> > +/***********************************************************************
> > ******* + * NOR Flash
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_MTD_PHYSMAP) ||
> > defined(CONFIG_MTD_PHYSMAP_MODULE) +static struct mtd_partition
> > sharpslc_rom_parts[] = {
> > {
> > .name ="Boot PROM Filesystem",
> > .offset = 0x00140000,
> > @@ -687,161 +823,152 @@ static struct mtd_partition sharpsl_rom_parts[] =
> > { },
> > };
> >
> > -static struct physmap_flash_data sharpsl_rom_data = {
> > +static struct physmap_flash_data sharpslc_rom_data = {
> > .width = 2,
> > - .nr_parts = ARRAY_SIZE(sharpsl_rom_parts),
> > - .parts = sharpsl_rom_parts,
> > + .nr_parts = ARRAY_SIZE(sharpslc_rom_parts),
> > + .parts = sharpslc_rom_parts,
> > };
> >
> > -static struct resource sharpsl_rom_resources[] = {
> > +static struct resource sharpslc_rom_resources[] = {
> > {
> > - .start = 0x00000000,
> > - .end = 0x007fffff,
> > + .start = PXA_CS0_PHYS,
> > + .end = PXA_CS0_PHYS + SZ_8M - 1,
> > .flags = IORESOURCE_MEM,
> > },
> > };
> >
> > -static struct platform_device sharpsl_rom_device = {
> > - .name = "physmap-flash",
> > - .id = -1,
> > - .resource = sharpsl_rom_resources,
> > - .num_resources = ARRAY_SIZE(sharpsl_rom_resources),
> > - .dev.platform_data = &sharpsl_rom_data,
> > -};
> > -
> > -static struct platform_device *devices[] __initdata = {
> > - &spitzscoop_device,
> > - &spitzkbd_device,
> > - &spitz_gpio_keys_device,
> > - &spitzled_device,
> > - &sharpsl_nand_device,
> > - &sharpsl_rom_device,
> > +static struct platform_device sharpslc_rom_device = {
> > + .name = "physmap-flash",
> > + .id = -1,
> > + .resource = sharpslc_rom_resources,
> > + .num_resources = ARRAY_SIZE(sharpslc_rom_resources),
> > + .dev = {
> > + .platform_data = &sharpslc_rom_data,
> > + },
> > };
> >
> > -static void spitz_poweroff(void)
> > +static void __init sharpslc_nor_init(void)
> > {
> > - arm_machine_restart('g', NULL);
> > + platform_device_register(&sharpslc_rom_device);
> > }
> > +#else
> > +static inline void sharpslc_nor_init(void) {}
> > +#endif
> >
> > -static void spitz_restart(char mode, const char *cmd)
> > -{
> > - /* Bootloader magic for a reboot */
> > - if((MSC0 & 0xffff0000) == 0x7ff00000)
> > - MSC0 = (MSC0 & 0xffff) | 0x7ee00000;
> > -
> > - spitz_poweroff();
> > -}
> > +/***********************************************************************
> > ******* + * GPIO expander
> > +
> > ************************************************************************
> > ******/ +#if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE)
> > +static struct pca953x_platform_data akita_pca953x_pdata = {
> > + .gpio_base = AKITA_IOEXP_GPIO_BASE,
> > +};
> >
> > -static void __init common_init(void)
> > -{
> > - init_gpio_reset(SPITZ_GPIO_ON_RESET, 1, 0);
> > - pm_power_off = spitz_poweroff;
> > - arm_pm_restart = spitz_restart;
> > +static struct i2c_board_info sharpslc_i2c_devs[] = {
> > + {
> > + .type = "wm8750",
> > + .addr = 0x1b,
> > + }, {
> > + .type = "max7310",
> > + .addr = 0x18,
> > + .platform_data = &akita_pca953x_pdata,
> > + },
> > +};
> >
> > - if (machine_is_spitz()) {
> > - sharpsl_nand_partitions[1].size = 5 * 1024 * 1024;
> > - } else if (machine_is_akita()) {
> > - sharpsl_nand_partitions[1].size = 58 * 1024 * 1024;
> > - } else if (machine_is_borzoi()) {
> > - sharpsl_nand_partitions[1].size = 32 * 1024 * 1024;
> > +static struct regulator_consumer_supply isl6271a_consumers[] = {
> > + {
> > + .supply = "vcc_core",
> > }
> > +};
> >
> > - PMCR = 0x00;
> > -
> > - /* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
> > - PCFR |= PCFR_OPDE;
> > +static struct regulator_init_data isl6271a_info[] = {
> > + {
> > + .constraints = {
> > + .name = "vcc_core range",
> > + .min_uV = 850000,
> > + .max_uV = 1600000,
> > + .always_on = 1,
> > + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
> > + },
> > + .consumer_supplies = isl6271a_consumers,
> > + .num_consumer_supplies = ARRAY_SIZE(isl6271a_consumers),
> > + }
> > +};
> >
> > - pxa2xx_mfp_config(ARRAY_AND_SIZE(spitz_pin_config));
> > +static struct i2c_board_info sharpslc_pi2c_devs[] = {
> > + {
> > + .type = "isl6271a",
> > + .addr = 0x0c,
> > + .platform_data = &isl6271a_info,
> > + },
> > +};
> >
> > - pxa_set_ffuart_info(NULL);
> > - pxa_set_btuart_info(NULL);
> > - pxa_set_stuart_info(NULL);
> > +static void __init sharpslc_i2c_init(void)
> > +{
> > + int size = ARRAY_SIZE(sharpslc_i2c_devs);
> >
> > - spitz_init_spi();
> > + /* Only Akita has the max7310 chip */
> > + if (!machine_is_akita())
> > + size--;
> >
> > - platform_add_devices(devices, ARRAY_SIZE(devices));
> > - pxa_set_mci_info(&spitz_mci_platform_data);
> > - pxa_set_ohci_info(&spitz_ohci_platform_data);
> > - pxa_set_ficp_info(&spitz_ficp_platform_data);
> > - set_pxa_fb_info(&spitz_pxafb_info);
> > pxa_set_i2c_info(NULL);
> > + pxa27x_set_i2c_power_info(NULL);
> > + i2c_register_board_info(0, sharpslc_i2c_devs, size);
> > + i2c_register_board_info(1, ARRAY_AND_SIZE(sharpslc_pi2c_devs));
> > }
> > -
> > -#if defined(CONFIG_MACH_AKITA) || defined(CONFIG_MACH_BORZOI)
> > -static struct nand_bbt_descr sharpsl_akita_bbt = {
> > - .options = 0,
> > - .offs = 4,
> > - .len = 1,
> > - .pattern = scan_ff_pattern
> > -};
> > -
> > -static struct nand_ecclayout akita_oobinfo = {
> > - .eccbytes = 24,
> > - .eccpos = {
> > - 0x5, 0x1, 0x2, 0x3, 0x6, 0x7, 0x15, 0x11,
> > - 0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23,
> > - 0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37},
> > - .oobfree = {{0x08, 0x09}}
> > -};
> > +#else
> > +static inline void sharpslc_i2c_init(void) {}
> > #endif
> >
> > -#if defined(CONFIG_MACH_SPITZ) || defined(CONFIG_MACH_BORZOI)
> > -static void __init spitz_init(void)
> > +/***********************************************************************
> > ******* + * Machine init
> > +
> > ************************************************************************
> > ******/ +static void sharpslc_poweroff(void)
> > {
> > - spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON;
> > -
> > -#ifdef CONFIG_MACH_BORZOI
> > - if (machine_is_borzoi()) {
> > - sharpsl_nand_platform_data.badblock_pattern =
> > &sharpsl_akita_bbt; -
> > sharpsl_nand_platform_data.ecc_layout = &akita_oobinfo; - }
> > -#endif
> > -
> > - platform_scoop_config = &spitz_pcmcia_config;
> > -
> > - common_init();
> > -
> > - platform_device_register(&spitzscoop2_device);
> > + arm_machine_restart('g', NULL);
> > }
> > -#endif
> >
> > -#ifdef CONFIG_MACH_AKITA
> > -/*
> > - * Akita IO Expander
> > - */
> > -static struct pca953x_platform_data akita_ioexp = {
> > - .gpio_base = AKITA_IOEXP_GPIO_BASE,
> > -};
> > +static void sharpslc_restart(char mode, const char *cmd)
> > +{
> > + /* Bootloader magic for a reboot */
> > + if ((MSC0 & 0xffff0000) == 0x7ff00000)
> > + MSC0 = (MSC0 & 0xffff) | 0x7ee00000;
> >
> > -static struct i2c_board_info akita_i2c_board_info[] = {
> > - {
> > - .type = "max7310",
> > - .addr = 0x18,
> > - .platform_data = &akita_ioexp,
> > - }, {
> > - .type = "wm8750",
> > - .addr = 0x1b,
> > - },
> > -};
> > + sharpslc_poweroff();
> > +}
> >
> > -static void __init akita_init(void)
> > +static void __init sharpslc_init(void)
> > {
> > - spitz_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON;
> > + init_gpio_reset(SPITZ_GPIO_ON_RESET, 1, 0);
> > + pm_power_off = sharpslc_poweroff;
> > + arm_pm_restart = sharpslc_restart;
> > +
> > + PMCR = 0x00;
> >
> > - sharpsl_nand_platform_data.badblock_pattern = &sharpsl_akita_bbt;
> > - sharpsl_nand_platform_data.ecc_layout = &akita_oobinfo;
> > + /* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
> > + PCFR |= PCFR_OPDE;
> >
> > - /* We just pretend the second element of the array doesn't exist
> > */ - spitz_pcmcia_config.num_devs = 1;
> > - platform_scoop_config = &spitz_pcmcia_config;
> > + pxa2xx_mfp_config(ARRAY_AND_SIZE(sharpslc_pin_config));
> >
> > - i2c_register_board_info(0, ARRAY_AND_SIZE(akita_i2c_board_info));
> > + pxa_set_ffuart_info(NULL);
> > + pxa_set_btuart_info(NULL);
> > + pxa_set_stuart_info(NULL);
> >
> > - common_init();
> > + sharpslc_spi_init();
> > + sharpslc_scoop_init();
> > + sharpslc_mkp_init();
> > + sharpslc_keys_init();
> > + sharpslc_leds_init();
> > + sharpslc_mmc_init();
> > + sharpslc_pcmcia_init();
> > + sharpslc_irda_init();
> > + sharpslc_uhc_init();
> > + sharpslc_lcd_init();
> > + sharpslc_nor_init();
> > + sharpslc_nand_init();
> > + sharpslc_i2c_init();
> > }
> > -#endif
> >
> > -static void __init fixup_spitz(struct machine_desc *desc,
> > +static void __init sharpslc_fixup(struct machine_desc *desc,
> > struct tag *tags, char **cmdline, struct meminfo *mi)
> > {
> > sharpsl_save_param();
> > @@ -855,10 +982,10 @@ static void __init fixup_spitz(struct machine_desc
> > *desc, MACHINE_START(SPITZ, "SHARP Spitz")
> > .phys_io = 0x40000000,
> > .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
> > - .fixup = fixup_spitz,
> > + .fixup = sharpslc_fixup,
> > .map_io = pxa_map_io,
> > .init_irq = pxa27x_init_irq,
> > - .init_machine = spitz_init,
> > + .init_machine = sharpslc_init,
> > .timer = &pxa_timer,
> > MACHINE_END
> > #endif
> > @@ -867,10 +994,10 @@ MACHINE_END
> > MACHINE_START(BORZOI, "SHARP Borzoi")
> > .phys_io = 0x40000000,
> > .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
> > - .fixup = fixup_spitz,
> > + .fixup = sharpslc_fixup,
> > .map_io = pxa_map_io,
> > .init_irq = pxa27x_init_irq,
> > - .init_machine = spitz_init,
> > + .init_machine = sharpslc_init,
> > .timer = &pxa_timer,
> > MACHINE_END
> > #endif
> > @@ -879,10 +1006,10 @@ MACHINE_END
> > MACHINE_START(AKITA, "SHARP Akita")
> > .phys_io = 0x40000000,
> > .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
> > - .fixup = fixup_spitz,
> > + .fixup = sharpslc_fixup,
> > .map_io = pxa_map_io,
> > .init_irq = pxa27x_init_irq,
> > - .init_machine = akita_init,
> > + .init_machine = sharpslc_init,
> > .timer = &pxa_timer,
> > MACHINE_END
> > #endif
> > --
> > 1.7.1
More information about the linux-arm-kernel
mailing list