[PATCH 1/2] mxc: add common debug board for 3-stack platforms
Jason Wang
jason77.wang at gmail.com
Sat Jun 12 10:25:06 EDT 2010
The debug board is little different for all mxc 3-stack(PDK)
platforms, it is possible here to add a common implementation to
support this board.
Signed-off-by: Jason Wang <jason77.wang at gmail.com>
---
arch/arm/plat-mxc/Kconfig | 11 ++
arch/arm/plat-mxc/Makefile | 1 +
arch/arm/plat-mxc/cpld_debugboard.c | 161 ++++++++++++++++++++++
arch/arm/plat-mxc/include/mach/cpld_debugboard.h | 60 ++++++++
4 files changed, 233 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/plat-mxc/cpld_debugboard.c
create mode 100644 arch/arm/plat-mxc/include/mach/cpld_debugboard.h
diff --git a/arch/arm/plat-mxc/Kconfig b/arch/arm/plat-mxc/Kconfig
index 7f7ad6f..8bf917e 100644
--- a/arch/arm/plat-mxc/Kconfig
+++ b/arch/arm/plat-mxc/Kconfig
@@ -81,6 +81,17 @@ config MXC_PWM
help
Enable support for the i.MX PWM controller(s).
+config MXC_DEBUG_BOARD
+ bool "Enable MXC debug board(for 3-stack)"
+ help
+ The debug board is an integral part of the MXC 3-stack(PDK)
+ platforms, it can be attached or removed from the peripheral
+ board. On debug board, several debug devices(ethernet, UART,
+ buttons, LEDs and JTAG) are implemented. Between the MCU and
+ these devices, a CPLD is added as a bridge which performs
+ data/address de-multiplexing and decode, signal level shift,
+ interrupt control and various board functions.
+
config MXC_ULPI
bool
diff --git a/arch/arm/plat-mxc/Makefile b/arch/arm/plat-mxc/Makefile
index 895bc3c..b9e8c6f 100644
--- a/arch/arm/plat-mxc/Makefile
+++ b/arch/arm/plat-mxc/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_USB_EHCI_MXC) += ehci.o
obj-$(CONFIG_MXC_ULPI) += ulpi.o
obj-$(CONFIG_ARCH_MXC_AUDMUX_V1) += audmux-v1.o
obj-$(CONFIG_ARCH_MXC_AUDMUX_V2) += audmux-v2.o
+obj-$(CONFIG_MXC_DEBUG_BOARD) += cpld_debugboard.o
ifdef CONFIG_SND_IMX_SOC
obj-y += ssi-fiq.o
obj-y += ssi-fiq-ksym.o
diff --git a/arch/arm/plat-mxc/cpld_debugboard.c b/arch/arm/plat-mxc/cpld_debugboard.c
new file mode 100644
index 0000000..0554fa0
--- /dev/null
+++ b/arch/arm/plat-mxc/cpld_debugboard.c
@@ -0,0 +1,161 @@
+/*
+ * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright (C) 2010 Jason Wang <jason77.wang at gmail.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/smsc911x.h>
+
+#include <mach/hardware.h>
+#include <mach/cpld_debugboard.h>
+
+static void __iomem *brd_io;
+static void expio_ack_irq(u32 irq);
+
+static struct resource smsc911x_resources[] = {
+ {
+ .flags = IORESOURCE_MEM,
+ } , {
+ .start = EXPIO_INT_ENET,
+ .end = EXPIO_INT_ENET,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct smsc911x_platform_config smsc911x_config = {
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .flags = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY,
+};
+
+struct platform_device smsc_lan9217_device = {
+ .name = "smsc911x",
+ .id = 0,
+ .dev = {
+ .platform_data = &smsc911x_config,
+ },
+ .num_resources = ARRAY_SIZE(smsc911x_resources),
+ .resource = smsc911x_resources,
+};
+
+static void mxc_expio_irq_handler(u32 irq, struct irq_desc *desc)
+{
+ u32 imr_val;
+ u32 int_valid;
+ u32 expio_irq;
+
+ desc->chip->mask(irq); /* irq = gpio irq number */
+
+ imr_val = __raw_readw(brd_io + INTR_MASK_REG);
+ int_valid = __raw_readw(brd_io + INTR_STATUS_REG) & ~imr_val;
+
+ expio_irq = MXC_BOARD_IRQ_START;
+ for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
+ struct irq_desc *d;
+ if ((int_valid & 1) == 0)
+ continue;
+ d = irq_desc + expio_irq;
+ if (unlikely(!(d->handle_irq)))
+ pr_err("\nEXPIO irq: %d unhandled\n", expio_irq);
+ else
+ d->handle_irq(expio_irq, d);
+ }
+
+ desc->chip->ack(irq);
+ desc->chip->unmask(irq);
+}
+
+/*
+ * Disable an expio pin's interrupt by setting the bit in the imr.
+ * Irq is an expio virtual irq number
+ */
+static void expio_mask_irq(u32 irq)
+{
+ u16 reg;
+ u32 expio = MXC_IRQ_TO_EXPIO(irq);
+
+ reg = __raw_readw(brd_io + INTR_MASK_REG);
+ reg |= (1 << expio);
+ __raw_writew(reg, brd_io + INTR_MASK_REG);
+}
+
+static void expio_ack_irq(u32 irq)
+{
+ u32 expio = MXC_IRQ_TO_EXPIO(irq);
+
+ __raw_writew(1 << expio, brd_io + INTR_RESET_REG);
+ __raw_writew(0, brd_io + INTR_RESET_REG);
+ expio_mask_irq(irq);
+}
+
+static void expio_unmask_irq(u32 irq)
+{
+ u16 reg;
+ u32 expio = MXC_IRQ_TO_EXPIO(irq);
+
+ reg = __raw_readw(brd_io + INTR_MASK_REG);
+ reg &= ~(1 << expio);
+ __raw_writew(reg, brd_io + INTR_MASK_REG);
+}
+
+static struct irq_chip expio_irq_chip = {
+ .ack = expio_ack_irq,
+ .mask = expio_mask_irq,
+ .unmask = expio_unmask_irq,
+};
+
+int __init mxc_expio_init(u32 base, u32 p_irq)
+{
+ int i;
+
+ brd_io = ioremap(BOARD_IO_ADDR(base), SZ_4K);
+ if (brd_io == NULL)
+ return -ENOMEM;
+
+ if ((__raw_readw(brd_io + MAGIC_NUMBER1_REG) != 0xAAAA) ||
+ (__raw_readw(brd_io + MAGIC_NUMBER2_REG) != 0x5555) ||
+ (__raw_readw(brd_io + MAGIC_NUMBER3_REG) != 0xCAFE)) {
+ pr_info("3-Stack Debug board not detected\n");
+ iounmap(brd_io);
+ brd_io = NULL;
+ return -ENODEV;
+ }
+
+ pr_info("3-Stack Debug board detected, rev = 0x%04X\n",
+ readw(brd_io + CPLD_CODE_VER_REG));
+
+ smsc911x_resources[0].start = LAN9217_BASE_ADDR(base);
+ smsc911x_resources[0].end = LAN9217_BASE_ADDR(base) + 0x100 - 1;
+
+ /*
+ * Configure INT line as GPIO input
+ */
+ gpio_request(MXC_IRQ_TO_GPIO(p_irq), "expio_pirq");
+ gpio_direction_input(MXC_IRQ_TO_GPIO(p_irq));
+
+ /* disable the interrupt and clear the status */
+ __raw_writew(0, brd_io + INTR_MASK_REG);
+ __raw_writew(0xFFFF, brd_io + INTR_RESET_REG);
+ __raw_writew(0, brd_io + INTR_RESET_REG);
+ __raw_writew(0x1F, brd_io + INTR_MASK_REG);
+ for (i = MXC_EXP_IO_BASE;
+ i < (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES); i++) {
+ set_irq_chip(i, &expio_irq_chip);
+ set_irq_handler(i, handle_level_irq);
+ set_irq_flags(i, IRQF_VALID);
+ }
+ set_irq_type(p_irq, IRQF_TRIGGER_LOW);
+ set_irq_chained_handler(p_irq, mxc_expio_irq_handler);
+
+ return 0;
+}
diff --git a/arch/arm/plat-mxc/include/mach/cpld_debugboard.h b/arch/arm/plat-mxc/include/mach/cpld_debugboard.h
new file mode 100644
index 0000000..a1422d2
--- /dev/null
+++ b/arch/arm/plat-mxc/include/mach/cpld_debugboard.h
@@ -0,0 +1,60 @@
+/*
+ * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __ASM_ARCH_MXC_CPLD_DB_H__
+#define __ASM_ARCH_MXC_CPLD_DB_H__
+
+/* LAN9217 ethernet base address */
+#define LAN9217_BASE_ADDR(n) (n + 0x0)
+/* External UART */
+#define UARTA_BASE_ADDR(n) (n + 0x8000)
+#define UARTB_BASE_ADDR(n) (n + 0x10000)
+
+#define BOARD_IO_ADDR(n) (n + 0x20000)
+/* LED switchs */
+#define LED_SWITCH_REG 0x00
+/* buttons */
+#define SWITCH_BUTTONS_REG 0x08
+/* status, interrupt */
+#define INTR_STATUS_REG 0x10
+#define INTR_MASK_REG 0x38
+#define INTR_RESET_REG 0x20
+/* magic word for debug CPLD */
+#define MAGIC_NUMBER1_REG 0x40
+#define MAGIC_NUMBER2_REG 0x48
+/* CPLD code version */
+#define CPLD_CODE_VER_REG 0x50
+/* magic word for debug CPLD */
+#define MAGIC_NUMBER3_REG 0x58
+/* module reset register*/
+#define MODULE_RESET_REG 0x60
+/* CPU ID and Personality ID */
+#define MCU_BOARD_ID_REG 0x68
+
+#define MXC_IRQ_TO_EXPIO(irq) ((irq) - MXC_BOARD_IRQ_START)
+#define MXC_IRQ_TO_GPIO(irq) ((irq) - MXC_INTERNAL_IRQS)
+
+#define MXC_EXP_IO_BASE (MXC_BOARD_IRQ_START)
+#define MXC_MAX_EXP_IO_LINES 16
+
+/* interrupts like external uart , external ethernet etc*/
+#define EXPIO_INT_ENET (MXC_BOARD_IRQ_START + 0)
+#define EXPIO_INT_XUART_A (MXC_BOARD_IRQ_START + 1)
+#define EXPIO_INT_XUART_B (MXC_BOARD_IRQ_START + 2)
+#define EXPIO_INT_BUTTON_A (MXC_BOARD_IRQ_START + 3)
+#define EXPIO_INT_BUTTON_B (MXC_BOARD_IRQ_START + 4)
+
+extern struct platform_device smsc_lan9217_device;
+
+int __init mxc_expio_init(u32 base, u32 p_irq);
+
+#endif /* __ASM_ARCH_MXC_CPLD_DB_H__ */
--
1.5.6.5
More information about the linux-arm-kernel
mailing list