[PATCH 10/13] [ARM] pxa/balloon3: PCMCIA Support
Marek Vasut
marek.vasut at gmail.com
Wed Jul 28 23:16:26 EDT 2010
This driver adds support for the on-board CF socket.
Signed-off-by: Marek Vasut <marek.vasut at gmail.com>
---
arch/arm/mach-pxa/balloon3.c | 13 ++-
arch/arm/mach-pxa/include/mach/balloon3.h | 17 ---
drivers/pcmcia/Kconfig | 2 +-
drivers/pcmcia/Makefile | 1 +
drivers/pcmcia/pxa2xx_balloon3.c | 199 +++++++++++++++++++++++++++++
5 files changed, 213 insertions(+), 19 deletions(-)
create mode 100644 drivers/pcmcia/pxa2xx_balloon3.c
diff --git a/arch/arm/mach-pxa/balloon3.c b/arch/arm/mach-pxa/balloon3.c
index 572525c..91ad56d 100644
--- a/arch/arm/mach-pxa/balloon3.c
+++ b/arch/arm/mach-pxa/balloon3.c
@@ -88,6 +88,18 @@ static unsigned long balloon3_pin_config[] __initdata = {
/* USB Host */
GPIO88_USBH1_PWR,
GPIO89_USBH1_PEN,
+
+ /* PC Card */
+ GPIO48_nPOE,
+ GPIO49_nPWE,
+ GPIO50_nPIOR,
+ GPIO51_nPIOW,
+ GPIO85_nPCE_1,
+ GPIO54_nPCE_2,
+ GPIO79_PSKTSEL,
+ GPIO55_nPREG,
+ GPIO56_nPWAIT,
+ GPIO57_nIOIS16,
};
/******************************************************************************
@@ -405,7 +417,6 @@ static void balloon3_irq_handler(unsigned int irq, struct irq_desc *desc)
{
unsigned long pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
balloon3_irq_enabled;
-
do {
/* clear useless edge notification */
if (desc->chip->ack)
diff --git a/arch/arm/mach-pxa/include/mach/balloon3.h b/arch/arm/mach-pxa/include/mach/balloon3.h
index 1a74106..14f4bd5 100644
--- a/arch/arm/mach-pxa/include/mach/balloon3.h
+++ b/arch/arm/mach-pxa/include/mach/balloon3.h
@@ -26,10 +26,6 @@ enum balloon3_features {
#define BALLOON3_FPGA_VIRT (0xf1000000) /* as per balloon2 */
#define BALLOON3_FPGA_LENGTH 0x01000000
-/* FPGA/CPLD registers */
-#define BALLOON3_PCMCIA0_REG (BALLOON3_FPGA_VIRT + 0x00e00008)
-/* fixme - same for now */
-#define BALLOON3_PCMCIA1_REG (BALLOON3_FPGA_VIRT + 0x00e00008)
#define BALLOON3_NANDIO_IO_REG (BALLOON3_FPGA_VIRT + 0x00e00000)
/* fpga/cpld interrupt control register */
#define BALLOON3_INT_CONTROL_REG (BALLOON3_FPGA_VIRT + 0x00e0000C)
@@ -58,16 +54,6 @@ enum balloon3_features {
#define BALLOON3_INT_S0_IRQ (1 << 0) /* PCMCIA 0 IRQ */
#define BALLOON3_INT_S0_STSCHG (1 << 1) /* PCMCIA 0 status changed */
-/* CF Status Register */
-#define BALLOON3_PCMCIA_nIRQ (1 << 0) /* IRQ / ready signal */
-#define BALLOON3_PCMCIA_nSTSCHG_BVD1 (1 << 1)
- /* VDD sense / card status changed */
-
-/* CF control register (write) */
-#define BALLOON3_PCMCIA_RESET (1 << 0) /* Card reset signal */
-#define BALLOON3_PCMCIA_ENABLE (1 << 1)
-#define BALLOON3_PCMCIA_ADD_ENABLE (1 << 2)
-
/* CPLD (and FPGA) interface definitions */
#define CPLD_LCD0_DATA_SET 0x00
#define CPLD_LCD0_DATA_CLR 0x10
@@ -132,9 +118,6 @@ enum balloon3_features {
/* Balloon3 Interrupts */
#define BALLOON3_IRQ(x) (IRQ_BOARD_START + (x))
-#define BALLOON3_BP_CF_NRDY_IRQ BALLOON3_IRQ(0)
-#define BALLOON3_BP_NSTSCHG_IRQ BALLOON3_IRQ(1)
-
#define BALLOON3_AUX_NIRQ IRQ_GPIO(BALLOON3_GPIO_AUX_NIRQ)
#define BALLOON3_CODEC_IRQ IRQ_GPIO(BALLOON3_GPIO_CODEC_IRQ)
#define BALLOON3_S0_CD_IRQ IRQ_GPIO(BALLOON3_GPIO_S0_CD)
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index d0f5ad3..ef2f659 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -215,7 +215,7 @@ config PCMCIA_PXA2XX
depends on (ARCH_LUBBOCK || MACH_MAINSTONE || PXA_SHARPSL \
|| MACH_ARMCORE || ARCH_PXA_PALM || TRIZEPS_PCMCIA \
|| ARCOM_PCMCIA || ARCH_PXA_ESERIES || MACH_STARGATE2 \
- || MACH_VPAC270)
+ || MACH_VPAC270 || MACH_BALLOON3)
select PCMCIA_SOC_COMMON
help
Say Y here to include support for the PXA2xx PCMCIA controller
diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile
index d006e8b..6a60773 100644
--- a/drivers/pcmcia/Makefile
+++ b/drivers/pcmcia/Makefile
@@ -70,6 +70,7 @@ pxa2xx-obj-$(CONFIG_MACH_PALMLD) += pxa2xx_palmld.o
pxa2xx-obj-$(CONFIG_MACH_E740) += pxa2xx_e740.o
pxa2xx-obj-$(CONFIG_MACH_STARGATE2) += pxa2xx_stargate2.o
pxa2xx-obj-$(CONFIG_MACH_VPAC270) += pxa2xx_vpac270.o
+pxa2xx-obj-$(CONFIG_MACH_BALLOON3) += pxa2xx_balloon3.o
obj-$(CONFIG_PCMCIA_PXA2XX) += pxa2xx_base.o $(pxa2xx-obj-y)
diff --git a/drivers/pcmcia/pxa2xx_balloon3.c b/drivers/pcmcia/pxa2xx_balloon3.c
new file mode 100644
index 0000000..1f71f0d
--- /dev/null
+++ b/drivers/pcmcia/pxa2xx_balloon3.c
@@ -0,0 +1,199 @@
+/*
+ * linux/drivers/pcmcia/pxa2xx_balloon3.c
+ *
+ * Balloon3 PCMCIA specific routines.
+ *
+ * Author: Nick Bane
+ * Created: June, 2006
+ * Copyright: Toby Churchill Ltd
+ * Derived from pxa2xx_mainstone.c, by Nico Pitre
+ *
+ * Various modification by Marek Vasut <marek.vasut at gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/gpio.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+
+#include <mach/balloon3.h>
+
+#include "soc_common.h"
+
+/*
+ * FPGA / CPLD register offsets for CF socket
+ */
+#define BALLOON3_CF_STATUS_REG (0x10e00008)
+#define BALLOON3_CF_CONTROL_REG (0x10e00008)
+#define BALLOON3_FPGA_VER (0x10e0001c)
+
+/* CF Status Register bits (read-only) bits */
+#define BALLOON3_CF_nIRQ (1 << 0)
+#define BALLOON3_CF_nSTSCHG_BVD1 (1 << 1)
+
+/* CF Control Set Register bits / CF Control Clear Register bits (write-only) */
+#define BALLOON3_CF_RESET (1 << 0)
+#define BALLOON3_CF_ENABLE (1 << 1)
+#define BALLOON3_CF_ADD_ENABLE (1 << 2)
+
+/* CF Interrupt sources */
+#define BALLOON3_BP_CF_NRDY_IRQ BALLOON3_IRQ(0)
+#define BALLOON3_BP_NSTSCHG_IRQ BALLOON3_IRQ(1)
+
+/*
+ * These are a list of interrupt sources that provokes a polled
+ * check of status
+ */
+static struct pcmcia_irqs irqs[] = {
+ { 0, BALLOON3_S0_CD_IRQ, "PCMCIA0 CD" },
+ { 0, BALLOON3_BP_NSTSCHG_IRQ, "PCMCIA0 STSCHG" },
+};
+
+static void __iomem *cf_control_reg;
+
+static int balloon3_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+ uint16_t ver;
+ int ret;
+ static void __iomem *fpga_ver;
+
+ cf_control_reg = ioremap(BALLOON3_CF_CONTROL_REG, 0x4);
+ if (!cf_control_reg) {
+ ret = -ENOMEM;
+ goto err1;
+ }
+
+ fpga_ver = ioremap(BALLOON3_FPGA_VER, 0x4);
+ if (!fpga_ver) {
+ ret = -ENOMEM;
+ goto err2;
+ }
+
+ ver = readw(fpga_ver);
+ if (ver > 0x0201)
+ pr_warn("The FPGA code, version 0x%04x, is newer than rel-0.3. "
+ "PCMCIA/CF support might be broken in this version!",
+ ver);
+
+ iounmap(fpga_ver);
+
+ skt->socket.pci_irq = BALLOON3_BP_CF_NRDY_IRQ;
+ return soc_pcmcia_request_irqs(skt, irqs, ARRAY_SIZE(irqs));
+
+err2:
+ iounmap(cf_control_reg);
+err1:
+ return ret;
+}
+
+static void balloon3_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+ soc_pcmcia_free_irqs(skt, irqs, ARRAY_SIZE(irqs));
+ iounmap(cf_control_reg);
+}
+
+static unsigned long balloon3_pcmcia_status[2] = {
+ BALLOON3_CF_nSTSCHG_BVD1,
+ BALLOON3_CF_nSTSCHG_BVD1
+};
+
+static void balloon3_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+ struct pcmcia_state *state)
+{
+ uint16_t status;
+ int flip;
+
+ /* This actually reads the STATUS register */
+ status = readw(cf_control_reg);
+ flip = (status ^ balloon3_pcmcia_status[skt->nr])
+ & BALLOON3_CF_nSTSCHG_BVD1;
+ /*
+ * Workaround for STSCHG which can't be deasserted:
+ * We therefore disable/enable corresponding IRQs
+ * as needed to avoid IRQ locks.
+ */
+ if (flip) {
+ balloon3_pcmcia_status[skt->nr] = status;
+ if (status & BALLOON3_CF_nSTSCHG_BVD1)
+ enable_irq(BALLOON3_BP_NSTSCHG_IRQ);
+ else
+ disable_irq(BALLOON3_BP_NSTSCHG_IRQ);
+ }
+
+ state->detect = !gpio_get_value(BALLOON3_GPIO_S0_CD);
+ state->ready = !!(status & BALLOON3_CF_nIRQ);
+ state->bvd1 = !!(status & BALLOON3_CF_nSTSCHG_BVD1);
+ state->bvd2 = 0; /* not available */
+ state->vs_3v = 1; /* Always true its a CF card */
+ state->vs_Xv = 0; /* not available */
+ state->wrprot = 0; /* not available */
+}
+
+static int balloon3_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+ const socket_state_t *state)
+{
+ writew((state->flags & SS_RESET) ? BALLOON3_CF_RESET:0, cf_control_reg);
+ return 0;
+}
+
+static void balloon3_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
+{
+}
+
+static void balloon3_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt)
+{
+}
+
+static struct pcmcia_low_level balloon3_pcmcia_ops = {
+ .owner = THIS_MODULE,
+ .hw_init = balloon3_pcmcia_hw_init,
+ .hw_shutdown = balloon3_pcmcia_hw_shutdown,
+ .socket_state = balloon3_pcmcia_socket_state,
+ .configure_socket = balloon3_pcmcia_configure_socket,
+ .socket_init = balloon3_pcmcia_socket_init,
+ .socket_suspend = balloon3_pcmcia_socket_suspend,
+ .first = 0,
+ .nr = 1,
+};
+
+static struct platform_device *balloon3_pcmcia_device;
+
+static int __init balloon3_pcmcia_init(void)
+{
+ int ret;
+
+ balloon3_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+ if (!balloon3_pcmcia_device)
+ return -ENOMEM;
+
+ ret = platform_device_add_data(balloon3_pcmcia_device,
+ &balloon3_pcmcia_ops, sizeof(balloon3_pcmcia_ops));
+
+ if (!ret)
+ ret = platform_device_add(balloon3_pcmcia_device);
+
+ if (ret)
+ platform_device_put(balloon3_pcmcia_device);
+
+ return ret;
+}
+
+static void __exit balloon3_pcmcia_exit(void)
+{
+ platform_device_unregister(balloon3_pcmcia_device);
+}
+
+module_init(balloon3_pcmcia_init);
+module_exit(balloon3_pcmcia_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Nick Bane <nick at cecomputing.co.uk>");
+MODULE_ALIAS("platform:pxa2xx-pcmcia");
+MODULE_DESCRIPTION("Balloon3 board CF/PCMCIA driver");
--
1.7.1
More information about the linux-arm-kernel
mailing list