[PATCH RFC] h1940: use gpiolib for latch access
Vasily Khoruzhick
anarsoul at gmail.com
Sun Jul 25 12:41:12 EDT 2010
This patch adds gpiolib support for h1940 latch.
With this patch it's possible to use leds-gpio and uda1380
drivers (they require gpiolib support for appropriate pins).
And now it's possible to drop leds-h1940 driver.
Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
---
arch/arm/mach-s3c2410/h1940-bluetooth.c | 21 ++++--
arch/arm/mach-s3c2410/include/mach/h1940-latch.h | 57 ++++++------------
arch/arm/mach-s3c2410/mach-h1940.c | 71 ++++++++++++++++++++--
arch/arm/plat-s3c24xx/Kconfig | 1 +
4 files changed, 99 insertions(+), 51 deletions(-)
diff --git a/arch/arm/mach-s3c2410/h1940-bluetooth.c b/arch/arm/mach-s3c2410/h1940-bluetooth.c
index 8cdeb14..6b86a72 100644
--- a/arch/arm/mach-s3c2410/h1940-bluetooth.c
+++ b/arch/arm/mach-s3c2410/h1940-bluetooth.c
@@ -30,7 +30,7 @@ static void h1940bt_enable(int on)
{
if (on) {
/* Power on the chip */
- h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER);
+ gpio_set_value(H1940_LATCH_BLUETOOTH_POWER, 1);
/* Reset the chip */
mdelay(10);
@@ -43,7 +43,7 @@ static void h1940bt_enable(int on)
mdelay(10);
gpio_set_value(S3C2410_GPH(1), 0);
mdelay(10);
- h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0);
+ gpio_set_value(H1940_LATCH_BLUETOOTH_POWER, 0);
}
}
@@ -64,19 +64,26 @@ static int __devinit h1940bt_probe(struct platform_device *pdev)
ret = gpio_request(S3C2410_GPH(1), dev_name(&pdev->dev));
if (ret) {
- dev_err(&pdev->dev, "could not get GPH1\n");\
+ dev_err(&pdev->dev, "could not get GPH1\n");
+ return ret;
+ }
+
+ ret = gpio_request(H1940_LATCH_BLUETOOTH_POWER, dev_name(&pdev->dev));
+ if (ret) {
+ gpio_free(S3C2410_GPH(1));
+ dev_err(&pdev->dev, "could not get BT_POWER\n");
return ret;
}
/* Configures BT serial port GPIOs */
s3c_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
- s3c_gpio_cfgpull(S3C2410_GPH(0), S3C_GPIO_PULL_NONE);
+ s3c_gpio_setpull(S3C2410_GPH(0), S3C_GPIO_PULL_NONE);
s3c_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT);
- s3c_gpio_cfgpull(S3C2410_GPH(1), S3C_GPIO_PULL_NONE);
+ s3c_gpio_setpull(S3C2410_GPH(1), S3C_GPIO_PULL_NONE);
s3c_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
- s3c_gpio_cfgpull(S3C2410_GPH(2), S3C_GPIO_PULL_NONE);
+ s3c_gpio_setpull(S3C2410_GPH(2), S3C_GPIO_PULL_NONE);
s3c_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
- s3c_gpio_cfgpull(S3C2410_GPH(3), S3C_GPIO_PULL_NONE);
+ s3c_gpio_setpull(S3C2410_GPH(3), S3C_GPIO_PULL_NONE);
rfk = rfkill_alloc(DRV_NAME, &pdev->dev, RFKILL_TYPE_BLUETOOTH,
diff --git a/arch/arm/mach-s3c2410/include/mach/h1940-latch.h b/arch/arm/mach-s3c2410/include/mach/h1940-latch.h
index d8a8327..4607d5c 100644
--- a/arch/arm/mach-s3c2410/include/mach/h1940-latch.h
+++ b/arch/arm/mach-s3c2410/include/mach/h1940-latch.h
@@ -14,51 +14,30 @@
#ifndef __ASM_ARCH_H1940_LATCH_H
#define __ASM_ARCH_H1940_LATCH_H
+#include <mach/gpio.h>
-#ifndef __ASSEMBLY__
-#define H1940_LATCH ((void __force __iomem *)0xF8000000)
-#else
-#define H1940_LATCH 0xF8000000
-#endif
-
-#define H1940_PA_LATCH (S3C2410_CS2)
+#define H1940_LATCH_GPIO(x) (S3C_GPIO_END + x)
/* SD layer latch */
-#define H1940_LATCH_SDQ1 (1<<16)
-#define H1940_LATCH_LCD_P1 (1<<17)
-#define H1940_LATCH_LCD_P2 (1<<18)
-#define H1940_LATCH_LCD_P3 (1<<19)
-#define H1940_LATCH_MAX1698_nSHUTDOWN (1<<20) /* LCD backlight */
-#define H1940_LATCH_LED_RED (1<<21)
-#define H1940_LATCH_SDQ7 (1<<22)
-#define H1940_LATCH_USB_DP (1<<23)
+#define H1940_LATCH_SDQ1 H1940_LATCH_GPIO(0)
+#define H1940_LATCH_LCD_P1 H1940_LATCH_GPIO(1)
+#define H1940_LATCH_LCD_P2 H1940_LATCH_GPIO(2)
+#define H1940_LATCH_LCD_P3 H1940_LATCH_GPIO(3)
+#define H1940_LATCH_MAX1698_nSHUTDOWN H1940_LATCH_GPIO(4)
+#define H1940_LATCH_LED_RED H1940_LATCH_GPIO(5)
+#define H1940_LATCH_SDQ7 H1940_LATCH_GPIO(6)
+#define H1940_LATCH_USB_DP H1940_LATCH_GPIO(7)
/* CPU layer latch */
-#define H1940_LATCH_UDA_POWER (1<<24)
-#define H1940_LATCH_AUDIO_POWER (1<<25)
-#define H1940_LATCH_SM803_ENABLE (1<<26)
-#define H1940_LATCH_LCD_P4 (1<<27)
-#define H1940_LATCH_CPUQ5 (1<<28) /* untraced */
-#define H1940_LATCH_BLUETOOTH_POWER (1<<29) /* active high */
-#define H1940_LATCH_LED_GREEN (1<<30)
-#define H1940_LATCH_LED_FLASH (1<<31)
-
-/* default settings */
-
-#define H1940_LATCH_DEFAULT \
- H1940_LATCH_LCD_P4 | \
- H1940_LATCH_SM803_ENABLE | \
- H1940_LATCH_SDQ1 | \
- H1940_LATCH_LCD_P1 | \
- H1940_LATCH_LCD_P2 | \
- H1940_LATCH_LCD_P3 | \
- H1940_LATCH_MAX1698_nSHUTDOWN | \
- H1940_LATCH_CPUQ5
-
-/* control functions */
-
-extern void h1940_latch_control(unsigned int clear, unsigned int set);
+#define H1940_LATCH_UDA_POWER H1940_LATCH_GPIO(8)
+#define H1940_LATCH_AUDIO_POWER H1940_LATCH_GPIO(9)
+#define H1940_LATCH_SM803_ENABLE H1940_LATCH_GPIO(10)
+#define H1940_LATCH_LCD_P4 H1940_LATCH_GPIO(11)
+#define H1940_LATCH_CPUQ5 H1940_LATCH_GPIO(12)
+#define H1940_LATCH_BLUETOOTH_POWER H1940_LATCH_GPIO(13)
+#define H1940_LATCH_LED_GREEN H1940_LATCH_GPIO(14)
+#define H1940_LATCH_LED_FLASH H1940_LATCH_GPIO(15)
#endif /* __ASM_ARCH_H1940_LATCH_H */
diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c
index 779b45b..693f467 100644
--- a/arch/arm/mach-s3c2410/mach-h1940.c
+++ b/arch/arm/mach-s3c2410/mach-h1940.c
@@ -42,6 +42,7 @@
#include <mach/regs-gpio.h>
#include <mach/gpio-fns.h>
#include <mach/gpio-nrs.h>
+#include <mach/gpio.h>
#include <mach/h1940.h>
#include <mach/h1940-latch.h>
@@ -58,6 +59,18 @@
#include <plat/mci.h>
#include <plat/ts.h>
+#ifndef __ASSEMBLY__
+#define H1940_LATCH ((void __force __iomem *)0xF8000000)
+#else
+#define H1940_LATCH 0xF8000000
+#endif
+
+#define H1940_PA_LATCH (S3C2410_CS2)
+
+#define H1940_LATCH_GPIO(x) (S3C_GPIO_END + x)
+
+#define H1940_LATCH_BIT(x) (1 << (x + 16 - S3C_GPIO_END))
+
static struct map_desc h1940_iodesc[] __initdata = {
[0] = {
.virtual = (unsigned long)H1940_LATCH,
@@ -99,9 +112,16 @@ static struct s3c2410_uartcfg h1940_uartcfgs[] __initdata = {
/* Board control latch control */
-static unsigned int latch_state = H1940_LATCH_DEFAULT;
+static unsigned int latch_state = H1940_LATCH_BIT(H1940_LATCH_LCD_P4) |
+ H1940_LATCH_BIT(H1940_LATCH_SM803_ENABLE) |
+ H1940_LATCH_BIT(H1940_LATCH_SDQ1) |
+ H1940_LATCH_BIT(H1940_LATCH_LCD_P1) |
+ H1940_LATCH_BIT(H1940_LATCH_LCD_P2) |
+ H1940_LATCH_BIT(H1940_LATCH_LCD_P3) |
+ H1940_LATCH_BIT(H1940_LATCH_MAX1698_nSHUTDOWN) |
+ H1940_LATCH_BIT(H1940_LATCH_CPUQ5);
-void h1940_latch_control(unsigned int clear, unsigned int set)
+static void h1940_latch_control(unsigned int clear, unsigned int set)
{
unsigned long flags;
@@ -115,7 +135,43 @@ void h1940_latch_control(unsigned int clear, unsigned int set)
local_irq_restore(flags);
}
-EXPORT_SYMBOL_GPL(h1940_latch_control);
+static int h1940_gpiolib_latch_input(struct gpio_chip *chip, unsigned offset)
+{
+ return -EINVAL;
+}
+
+
+static void h1940_gpiolib_latch_set(struct gpio_chip *chip,
+ unsigned offset, int value)
+{
+ h1940_latch_control(value ? 0 : (1 << (offset + 16)),
+ value ? (1 << (offset + 16)) : 0);
+}
+
+static int h1940_gpiolib_latch_output(struct gpio_chip *chip,
+ unsigned offset, int value)
+{
+ h1940_gpiolib_latch_set(chip, offset, value);
+
+ return 0;
+}
+
+static int h1940_gpiolib_latch_get(struct gpio_chip *chip,
+ unsigned offset)
+{
+ return (latch_state >> (offset + 16)) & 1;
+}
+
+struct gpio_chip h1940_latch_gpiochip = {
+ .base = H1940_LATCH_GPIO(0),
+ .owner = THIS_MODULE,
+ .label = "H1940_LATCH",
+ .ngpio = 16,
+ .direction_input = h1940_gpiolib_latch_input,
+ .direction_output = h1940_gpiolib_latch_output,
+ .set = h1940_gpiolib_latch_set,
+ .get = h1940_gpiolib_latch_get,
+};
static void h1940_udc_pullup(enum s3c2410_udc_cmd_e cmd)
{
@@ -124,10 +180,10 @@ static void h1940_udc_pullup(enum s3c2410_udc_cmd_e cmd)
switch (cmd)
{
case S3C2410_UDC_P_ENABLE :
- h1940_latch_control(0, H1940_LATCH_USB_DP);
+ gpio_set_value(H1940_LATCH_USB_DP, 1);
break;
case S3C2410_UDC_P_DISABLE :
- h1940_latch_control(H1940_LATCH_USB_DP, 0);
+ gpio_set_value(H1940_LATCH_USB_DP, 0);
break;
case S3C2410_UDC_P_RESET :
break;
@@ -302,6 +358,8 @@ static void __init h1940_map_io(void)
memcpy(phys_to_virt(H1940_SUSPEND_RESUMEAT), h1940_pm_return, 1024);
#endif
s3c_pm_init();
+
+ WARN_ON(gpiochip_add(&h1940_latch_gpiochip));
}
static void __init h1940_init_irq(void)
@@ -335,6 +393,9 @@ static void __init h1940_init(void)
gpio_request(S3C2410_GPC(5), "LCD power");
gpio_request(S3C2410_GPC(6), "LCD power");
+ gpio_request(H1940_LATCH_USB_DP, "USB pullup");
+ gpio_direction_output(H1940_LATCH_USB_DP, 0);
+
gpio_direction_input(S3C2410_GPC(6));
platform_add_devices(h1940_devices, ARRAY_SIZE(h1940_devices));
diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig
index 984bf66..5a27b1b 100644
--- a/arch/arm/plat-s3c24xx/Kconfig
+++ b/arch/arm/plat-s3c24xx/Kconfig
@@ -69,6 +69,7 @@ config S3C24XX_GPIO_EXTRA
int
default 128 if S3C24XX_GPIO_EXTRA128
default 64 if S3C24XX_GPIO_EXTRA64
+ default 16 if ARCH_H1940
default 0
config S3C24XX_GPIO_EXTRA64
--
1.7.1.1
More information about the linux-arm-kernel
mailing list