[PATCH v3] Samsung: sdhci-s3c: add support for new card detection methods
Andrew Morton
akpm at linux-foundation.org
Wed Jul 21 19:11:33 EDT 2010
On Fri, 16 Jul 2010 08:24:26 +0200
Marek Szyprowski <m.szyprowski at samsung.com> wrote:
> > > arch/arm/mach-s3c64xx/setup-sdhci-gpio.c | 14 +++++++++---
> > > arch/arm/mach-s5pc100/setup-sdhci-gpio.c | 21 ++++++++++++++-----
> > > arch/arm/mach-s5pv210/setup-sdhci-gpio.c | 22 +++++++++++++++-----
> > > arch/arm/plat-samsung/dev-hsmmc.c | 5 ++++
> > > arch/arm/plat-samsung/dev-hsmmc1.c | 5 ++++
> > > arch/arm/plat-samsung/dev-hsmmc2.c | 5 ++++
> > > arch/arm/plat-samsung/dev-hsmmc3.c | 5 ++++
> > > arch/arm/plat-samsung/include/plat/sdhci.h | 29
> > ++++++++++++++++++++++++++++
> > > 8 files changed, 90 insertions(+), 16 deletions(-)
> >
> > This is quite confusing. You've already sent a patch called
> > "sdhci-s3c: add support for new card detection methods". It had the
> > same changelog as this patch and the same title, but the two patches
> > are utterly different!
>
> The real patch has been split into two for easier merging: 1. the driver
> part and 2. samsung platform related part. The part which patch belongs
> to is indicated in the last line of the change log.
>
> I'm really confused how to submit properly a patch that requires changes
> to both the driver (which is merged by the proper driver maintainer's
> sub-tree) and the platform (which should go through platform maintainer's
> tree).
Make the relationship very very clear in the changelog. Send both
patches to both maintainers. Ask that one of them merge both patches
and that the other ack both patches.
Anyway, I've forgotten what's happening here. I appear to be sitting on
sdhci-s3c-add-support-for-the-non-standard-minimal-clock-value.patch
and
sdhci-s3c-add-support-for-new-card-detection-methods.patch
the latter of which is below.
Am I missing something? Is
sdhci-s3c-add-support-for-new-card-detection-methods.patch up to date?
From: Marek Szyprowski <m.szyprowski at samsung.com>
On some Samsung SoCs not all SDHCI controllers have card detect (CD) line.
For some embedded designs it is not even needed, because ususally the
device (like SDIO flash memory or wifi controller) is permanently wired to
the controller. There are also systems which have a card detect line
connected to some of the external interrupt lines or the presence of the
card depends on some other actions (like enabling a power regulator).
This patch adds support for all these cases. The following card detection
methods are possible:
1. internal sdhci host card detect line
2. external event
3. external gpio interrupt
4. no card detect line, controller will poll for the card
5. no card detect line, card is permanently wired to the controller
(once detected host won't poll it any more)
By default, all existing code would use method #1, what is compatible with
the previous version of the driver.
In case of external event, two callbacks must be provided in platdata:
ext_cd_init and ext_cd_cleanup. Both of them get a callback to a function
that notifies the s3c-sdhci host contoller as their argument. That
callback function should be called from the even dispatcher to let host
notice the card insertion/removal.
In case of external gpio interrupt, a gpio pin number must be provided in
platdata (ext_cd_gpio parameter), as well as the information about the
polarity of that gpio pin (ext_cd_gpio_invert). By default
(ext_cd_gpio_invert == 0) gpio value 0 means 'card has been removed', but
this can be changed to 'card has been removed' when ext_cd_gpio_invert ==
1.
This patch adds changes to sdhci-s3c driver.
Signed-off-by: Marek Szyprowski <m.szyprowski at samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
Signed-off-by: Andrew Morton <akpm at linux-foundation.org>
---
drivers/mmc/host/sdhci-s3c.c | 75 +++++++++++++++++++++++++++++++++
1 file changed, 75 insertions(+)
diff -puN drivers/mmc/host/sdhci-s3c.c~sdhci-s3c-add-support-for-new-card-detection-methods drivers/mmc/host/sdhci-s3c.c
--- a/drivers/mmc/host/sdhci-s3c.c~sdhci-s3c-add-support-for-new-card-detection-methods
+++ a/drivers/mmc/host/sdhci-s3c.c
@@ -18,6 +18,7 @@
#include <linux/slab.h>
#include <linux/clk.h>
#include <linux/io.h>
+#include <linux/gpio.h>
#include <linux/mmc/host.h>
@@ -44,6 +45,8 @@ struct sdhci_s3c {
struct resource *ioarea;
struct s3c_sdhci_platdata *pdata;
unsigned int cur_clk;
+ int ext_cd_irq;
+ int ext_cd_gpio;
struct clk *clk_io;
struct clk *clk_bus[MAX_BUS_CLK];
@@ -242,6 +245,39 @@ static struct sdhci_ops sdhci_s3c_ops =
.get_min_clock = sdhci_s3c_get_min_clock,
};
+static void sdhci_s3c_notify_change(struct platform_device *dev, int state)
+{
+ struct sdhci_host *host;
+ unsigned long flags;
+
+ host = platform_get_drvdata(dev);
+ if (host) {
+ spin_lock_irqsave(&host->lock, flags);
+ if (state) {
+ dev_dbg(&dev->dev, "card inserted.\n");
+ host->flags &= ~SDHCI_DEVICE_DEAD;
+ host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
+ tasklet_schedule(&host->card_tasklet);
+ } else {
+ dev_dbg(&dev->dev, "card removed.\n");
+ host->flags |= SDHCI_DEVICE_DEAD;
+ host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
+ tasklet_schedule(&host->card_tasklet);
+ }
+ spin_unlock_irqrestore(&host->lock, flags);
+ }
+}
+
+static irqreturn_t sdhci_s3c_gpio_card_detect_isr(int irq, void *dev_id)
+{
+ struct sdhci_s3c *sc = dev_id;
+ int status = gpio_get_value(sc->ext_cd_gpio);
+ if (sc->pdata->ext_cd_gpio_invert)
+ status = !status;
+ sdhci_s3c_notify_change(sc->pdev, status);
+ return IRQ_HANDLED;
+}
+
static int __devinit sdhci_s3c_probe(struct platform_device *pdev)
{
struct s3c_sdhci_platdata *pdata = pdev->dev.platform_data;
@@ -279,6 +315,7 @@ static int __devinit sdhci_s3c_probe(str
sc->host = host;
sc->pdev = pdev;
sc->pdata = pdata;
+ sc->ext_cd_gpio = -1;
platform_set_drvdata(pdev, host);
@@ -361,6 +398,13 @@ static int __devinit sdhci_s3c_probe(str
* SDHCI block, or a missing configuration that needs to be set. */
host->quirks |= SDHCI_QUIRK_NO_BUSY_IRQ;
+ if (pdata->cd_type == S3C_SDHCI_CD_NONE ||
+ pdata->cd_type == S3C_SDHCI_CD_PERMANENT)
+ host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
+
+ if (pdata->cd_type == S3C_SDHCI_CD_PERMANENT)
+ host->mmc->caps = MMC_CAP_NONREMOVABLE;
+
host->quirks |= (SDHCI_QUIRK_32BIT_DMA_ADDR |
SDHCI_QUIRK_32BIT_DMA_SIZE);
@@ -370,6 +414,27 @@ static int __devinit sdhci_s3c_probe(str
goto err_add_host;
}
+ /* pdata->ext_cd_init might call sdhci_s3c_notify_change immediately,
+ so it can be called only after sdhci_add_host() */
+ if (pdata->cd_type == S3C_SDHCI_CD_EXTERNAL && pdata->ext_cd_init)
+ pdata->ext_cd_init(&sdhci_s3c_notify_change);
+
+ if (pdata->cd_type == S3C_SDHCI_CD_GPIO &&
+ gpio_is_valid(pdata->ext_cd_gpio)) {
+
+ gpio_request(pdata->ext_cd_gpio, "SDHCI EXT CD");
+ sc->ext_cd_gpio = pdata->ext_cd_gpio;
+
+ sc->ext_cd_irq = gpio_to_irq(pdata->ext_cd_gpio);
+ if (sc->ext_cd_irq &&
+ request_irq(sc->ext_cd_irq, sdhci_s3c_gpio_card_detect_isr,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ dev_name(&pdev->dev), sc)) {
+ dev_err(&pdev->dev, "cannot request irq for card detect\n");
+ sc->ext_cd_irq = 0;
+ }
+ }
+
return 0;
err_add_host:
@@ -394,10 +459,20 @@ static int __devinit sdhci_s3c_probe(str
static int __devexit sdhci_s3c_remove(struct platform_device *pdev)
{
+ struct s3c_sdhci_platdata *pdata = pdev->dev.platform_data;
struct sdhci_host *host = platform_get_drvdata(pdev);
struct sdhci_s3c *sc = sdhci_priv(host);
int ptr;
+ if (pdata->cd_type == S3C_SDHCI_CD_EXTERNAL && pdata->ext_cd_cleanup)
+ pdata->ext_cd_cleanup(&sdhci_s3c_notify_change);
+
+ if (sc->ext_cd_irq)
+ free_irq(sc->ext_cd_irq, sdhci_s3c_gpio_card_detect_isr);
+
+ if (sc->ext_cd_gpio != -1)
+ gpio_free(sc->ext_cd_gpio);
+
sdhci_remove_host(host, 1);
for (ptr = 0; ptr < 3; ptr++) {
_
More information about the linux-arm-kernel
mailing list