[PATCH v7] libata: pata_samsung: Add Samsung PATA controller driver
Kukjin Kim
kgene.kim at samsung.com
Tue Jul 13 00:23:05 EDT 2010
From: Abhilash Kesavan <a.kesavan at samsung.com>
Adds support for the Samsung PATA controller. This driver is based on the
Libata subsystem and references the earlier patches sent for IDE subsystem.
Signed-off-by: Abhilash Kesavan <a.kesavan at samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim at samsung.com>
Cc: Ben Dooks <ben-linux at fluff.org>
Acked-by: Sergei Shtylyov <sshtylyov at mvista.com>
---
Changes since v6:
- Removed check for device 1 in pata_s3c_wait_after_reset() and
associated changes
- Initialized directly in pata_s3c_remove() and pata_s3c_resume()
drivers/ata/Kconfig | 9 +
drivers/ata/Makefile | 1 +
drivers/ata/pata_samsung_cf.c | 683 +++++++++++++++++++++++++++++++++++++++++
3 files changed, 693 insertions(+), 0 deletions(-)
create mode 100644 drivers/ata/pata_samsung_cf.c
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index aa85a98..1b5facf 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -796,6 +796,15 @@ config PATA_RZ1000
If unsure, say N.
+config PATA_SAMSUNG_CF
+ tristate "Samsung SoC PATA support"
+ depends on SAMSUNG_DEV_IDE
+ help
+ This option enables basic support for Samsung's S3C/S5P board
+ PATA controllers via the new ATA layer
+
+ If unsure, say N.
+
config PATA_WINBOND_VLB
tristate "Winbond W83759A VLB PATA support (Experimental)"
depends on ISA && EXPERIMENTAL
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 7ef89d7..9576776 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -87,6 +87,7 @@ obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o
obj-$(CONFIG_PATA_QDI) += pata_qdi.o
obj-$(CONFIG_PATA_RB532) += pata_rb532_cf.o
obj-$(CONFIG_PATA_RZ1000) += pata_rz1000.o
+obj-$(CONFIG_PATA_SAMSUNG_CF) += pata_samsung_cf.o
obj-$(CONFIG_PATA_WINBOND_VLB) += pata_winbond.o
# Should be last but two libata driver
diff --git a/drivers/ata/pata_samsung_cf.c b/drivers/ata/pata_samsung_cf.c
new file mode 100644
index 0000000..6f9cfb2
--- /dev/null
+++ b/drivers/ata/pata_samsung_cf.c
@@ -0,0 +1,683 @@
+/*
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * PATA driver for Samsung SoCs.
+ * Supports CF Interface in True IDE mode. Currently only PIO mode has been
+ * implemented; UDMA support has to be added.
+ *
+ * Based on:
+ * PATA driver for AT91SAM9260 Static Memory Controller
+ * PATA driver for Toshiba SCC controller
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/libata.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include <plat/ata.h>
+#include <plat/regs-ata.h>
+
+#define DRV_NAME "pata_samsung_cf"
+#define DRV_VERSION "0.1"
+
+enum s3c_cpu_type {
+ TYPE_S3C64XX,
+ TYPE_S5PC100,
+ TYPE_S5PV210,
+};
+
+/*
+ * struct s3c_ide_info - S3C PATA instance.
+ * @clk: The clock resource for this controller.
+ * @ide_addr: The area mapped for the hardware registers.
+ * @sfr_addr: The area mapped for the special function registers.
+ * @irq: The IRQ number we are using.
+ * @cpu_type: The exact type of this controller.
+ * @fifo_status_reg: The ATA_FIFO_STATUS register offset.
+ */
+struct s3c_ide_info {
+ struct clk *clk;
+ void __iomem *ide_addr;
+ void __iomem *sfr_addr;
+ unsigned int irq;
+ enum s3c_cpu_type cpu_type;
+ unsigned int fifo_status_reg;
+};
+
+static void pata_s3c_set_endian(void __iomem *s3c_ide_regbase, u8 mode)
+{
+ u32 reg = readl(s3c_ide_regbase + S3C_ATA_CFG);
+ reg = mode ? (reg & ~S3C_ATA_CFG_SWAP) : (reg | S3C_ATA_CFG_SWAP);
+ writel(reg, s3c_ide_regbase + S3C_ATA_CFG);
+}
+
+static void pata_s3c_cfg_mode(void __iomem *s3c_ide_sfrbase)
+{
+ /* Select true-ide as the internal operating mode */
+ writel(readl(s3c_ide_sfrbase + S3C_CFATA_MUX) | S3C_CFATA_MUX_TRUEIDE,
+ s3c_ide_sfrbase + S3C_CFATA_MUX);
+}
+
+static unsigned long
+pata_s3c_setup_timing(struct s3c_ide_info *info, const struct ata_timing *ata)
+{
+ int t1 = ata->setup;
+ int t2 = ata->act8b;
+ int t2i = ata->rec8b;
+ ulong piotime;
+
+ piotime = ((t2i & 0xff) << 12) | ((t2 & 0xff) << 4) | (t1 & 0xf);
+
+ return piotime;
+}
+
+static void pata_s3c_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct s3c_ide_info *info = ap->host->private_data;
+ struct ata_timing timing;
+ int cycle_time;
+ ulong ata_cfg = readl(info->ide_addr + S3C_ATA_CFG);
+ ulong piotime;
+
+ /* Enables IORDY if mode requires it */
+ if (ata_pio_need_iordy(adev))
+ ata_cfg |= S3C_ATA_CFG_IORDYEN;
+ else
+ ata_cfg &= ~S3C_ATA_CFG_IORDYEN;
+
+ cycle_time = (int)(1000000000UL / clk_get_rate(info->clk));
+
+ ata_timing_compute(adev, adev->pio_mode, &timing,
+ cycle_time * 1000, 0);
+
+ piotime = pata_s3c_setup_timing(info, &timing);
+
+ writel(ata_cfg, info->ide_addr + S3C_ATA_CFG);
+ writel(piotime, info->ide_addr + S3C_ATA_PIO_TIME);
+}
+
+/*
+ * Waits until the IDE controller is able to perform next read/write
+ * operation to the disk. Needed for 64XX series boards only.
+ */
+static int wait_for_host_ready(struct s3c_ide_info *info)
+{
+ ulong timeout;
+ void __iomem *fifo_reg = info->ide_addr + info->fifo_status_reg;
+
+ /* wait for maximum of 20 msec */
+ timeout = jiffies + msecs_to_jiffies(20);
+ while (time_before(jiffies, timeout)) {
+ if ((readl(fifo_reg) >> 28) == 0)
+ return 0;
+ }
+ return -EBUSY;
+}
+
+/*
+ * Writes to one of the task file registers.
+ */
+static void ata_outb(struct ata_host *host, u8 addr, void __iomem *reg)
+{
+ struct s3c_ide_info *info = host->private_data;
+
+ wait_for_host_ready(info);
+ writeb(addr, reg);
+}
+
+/*
+ * Reads from one of the task file registers.
+ */
+static u8 ata_inb(struct ata_host *host, void __iomem *reg)
+{
+ struct s3c_ide_info *info = host->private_data;
+ u8 temp;
+
+ wait_for_host_ready(info);
+ (void) readb(reg);
+ wait_for_host_ready(info);
+ temp = readb(info->ide_addr + S3C_ATA_PIO_RDATA);
+ return temp;
+}
+
+/*
+ * pata_s3c_tf_load - send taskfile registers to host controller
+ */
+static void pata_s3c_tf_load(struct ata_port *ap,
+ const struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
+
+ if (tf->ctl != ap->last_ctl) {
+ ata_outb(ap->host, tf->ctl, ioaddr->ctl_addr);
+ ap->last_ctl = tf->ctl;
+ ata_wait_idle(ap);
+ }
+
+ if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
+ ata_outb(ap->host, tf->hob_feature, ioaddr->feature_addr);
+ ata_outb(ap->host, tf->hob_nsect, ioaddr->nsect_addr);
+ ata_outb(ap->host, tf->hob_lbal, ioaddr->lbal_addr);
+ ata_outb(ap->host, tf->hob_lbam, ioaddr->lbam_addr);
+ ata_outb(ap->host, tf->hob_lbah, ioaddr->lbah_addr);
+ }
+
+ if (is_addr) {
+ ata_outb(ap->host, tf->feature, ioaddr->feature_addr);
+ ata_outb(ap->host, tf->nsect, ioaddr->nsect_addr);
+ ata_outb(ap->host, tf->lbal, ioaddr->lbal_addr);
+ ata_outb(ap->host, tf->lbam, ioaddr->lbam_addr);
+ ata_outb(ap->host, tf->lbah, ioaddr->lbah_addr);
+ }
+
+ if (tf->flags & ATA_TFLAG_DEVICE)
+ ata_outb(ap->host, tf->device, ioaddr->device_addr);
+
+ ata_wait_idle(ap);
+}
+
+/*
+ * pata_s3c_tf_read - input device's ATA taskfile shadow registers
+ */
+static void pata_s3c_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ tf->feature = ata_inb(ap->host, ioaddr->error_addr);
+ tf->nsect = ata_inb(ap->host, ioaddr->nsect_addr);
+ tf->lbal = ata_inb(ap->host, ioaddr->lbal_addr);
+ tf->lbam = ata_inb(ap->host, ioaddr->lbam_addr);
+ tf->lbah = ata_inb(ap->host, ioaddr->lbah_addr);
+ tf->device = ata_inb(ap->host, ioaddr->device_addr);
+
+ if (tf->flags & ATA_TFLAG_LBA48) {
+ ata_outb(ap->host, tf->ctl | ATA_HOB, ioaddr->ctl_addr);
+ tf->hob_feature = ata_inb(ap->host, ioaddr->error_addr);
+ tf->hob_nsect = ata_inb(ap->host, ioaddr->nsect_addr);
+ tf->hob_lbal = ata_inb(ap->host, ioaddr->lbal_addr);
+ tf->hob_lbam = ata_inb(ap->host, ioaddr->lbam_addr);
+ tf->hob_lbah = ata_inb(ap->host, ioaddr->lbah_addr);
+ ata_outb(ap->host, tf->ctl, ioaddr->ctl_addr);
+ ap->last_ctl = tf->ctl;
+ }
+}
+
+/*
+ * pata_s3c_exec_command - issue ATA command to host controller
+ */
+static void pata_s3c_exec_command(struct ata_port *ap,
+ const struct ata_taskfile *tf)
+{
+ ata_outb(ap->host, tf->command, ap->ioaddr.command_addr);
+ ata_sff_pause(ap);
+}
+
+/*
+ * pata_s3c_check_status - Read device status register
+ */
+static u8 pata_s3c_check_status(struct ata_port *ap)
+{
+ return ata_inb(ap->host, ap->ioaddr.status_addr);
+}
+
+/*
+ * pata_s3c_check_altstatus - Read alternate device status register
+ */
+static u8 pata_s3c_check_altstatus(struct ata_port *ap)
+{
+ return ata_inb(ap->host, ap->ioaddr.altstatus_addr);
+}
+
+/*
+ * pata_s3c_data_xfer - Transfer data by PIO
+ */
+unsigned int pata_s3c_data_xfer(struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw)
+{
+ struct ata_port *ap = dev->link->ap;
+ struct s3c_ide_info *info = ap->host->private_data;
+ void __iomem *data_addr = ap->ioaddr.data_addr;
+ unsigned int words = buflen >> 1, i;
+ u16 *data_ptr = (u16 *)buf;
+
+ /* Requires wait same as in ata_inb/ata_outb */
+ if (rw == READ)
+ for (i = 0; i < words; i++, data_ptr++) {
+ wait_for_host_ready(info);
+ (void) readw(data_addr);
+ wait_for_host_ready(info);
+ *data_ptr = readw(info->ide_addr
+ + S3C_ATA_PIO_RDATA);
+ }
+ else
+ for (i = 0; i < words; i++, data_ptr++) {
+ wait_for_host_ready(info);
+ writew(*data_ptr, data_addr);
+ }
+
+ if (buflen & 0x01)
+ dev_err(ap->dev, "unexpected trailing data\n");
+
+ return words << 1;
+}
+
+/*
+ * pata_s3c_dev_select - Select device on ATA bus
+ */
+static void pata_s3c_dev_select(struct ata_port *ap, unsigned int device)
+{
+ u8 tmp = ATA_DEVICE_OBS;
+
+ if (device != 0)
+ tmp |= ATA_DEV1;
+
+ ata_outb(ap->host, tmp, ap->ioaddr.device_addr);
+ ata_sff_pause(ap);
+}
+
+/*
+ * pata_s3c_devchk - PATA device presence detection
+ */
+static unsigned int pata_s3c_devchk(struct ata_port *ap,
+ unsigned int device)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ u8 nsect, lbal;
+
+ pata_s3c_dev_select(ap, device);
+
+ ata_outb(ap->host, 0x55, ioaddr->nsect_addr);
+ ata_outb(ap->host, 0xaa, ioaddr->lbal_addr);
+
+ ata_outb(ap->host, 0xaa, ioaddr->nsect_addr);
+ ata_outb(ap->host, 0x55, ioaddr->lbal_addr);
+
+ ata_outb(ap->host, 0x55, ioaddr->nsect_addr);
+ ata_outb(ap->host, 0xaa, ioaddr->lbal_addr);
+
+ nsect = ata_inb(ap->host, ioaddr->nsect_addr);
+ lbal = ata_inb(ap->host, ioaddr->lbal_addr);
+
+ if ((nsect == 0x55) && (lbal == 0xaa))
+ return 1; /* we found a device */
+
+ return 0; /* nothing found */
+}
+
+/*
+ * pata_s3c_wait_after_reset - wait for devices to become ready after reset
+ */
+static int pata_s3c_wait_after_reset(struct ata_link *link,
+ unsigned long deadline)
+{
+ int rc;
+
+ msleep(ATA_WAIT_AFTER_RESET);
+
+ /* always check readiness of the master device */
+ rc = ata_sff_wait_ready(link, deadline);
+ /* -ENODEV means the odd clown forgot the D7 pulldown resistor
+ * and TF status is 0xff, bail out on it too.
+ */
+ if (rc)
+ return rc;
+
+ return 0;
+}
+
+/*
+ * pata_s3c_bus_softreset - PATA device software reset
+ */
+static unsigned int pata_s3c_bus_softreset(struct ata_port *ap,
+ unsigned long deadline)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ /* software reset. causes dev0 to be selected */
+ ata_outb(ap->host, ap->ctl, ioaddr->ctl_addr);
+ udelay(20);
+ ata_outb(ap->host, ap->ctl | ATA_SRST, ioaddr->ctl_addr);
+ udelay(20);
+ ata_outb(ap->host, ap->ctl, ioaddr->ctl_addr);
+ ap->last_ctl = ap->ctl;
+
+ return pata_s3c_wait_after_reset(&ap->link, deadline);
+}
+
+/*
+ * pata_s3c_softreset - reset host port via ATA SRST
+ */
+static int pata_s3c_softreset(struct ata_link *link, unsigned int *classes,
+ unsigned long deadline)
+{
+ struct ata_port *ap = link->ap;
+ unsigned int devmask = 0;
+ int rc;
+ u8 err;
+
+ /* determine if device 0 is present */
+ if (pata_s3c_devchk(ap, 0))
+ devmask |= (1 << 0);
+
+ /* select device 0 again */
+ pata_s3c_dev_select(ap, 0);
+
+ /* issue bus reset */
+ rc = pata_s3c_bus_softreset(ap, deadline);
+ /* if link is occupied, -ENODEV too is an error */
+ if (rc && rc != -ENODEV) {
+ ata_link_printk(link, KERN_ERR, "SRST failed (errno=%d)\n", rc);
+ return rc;
+ }
+
+ /* determine by signature whether we have ATA or ATAPI devices */
+ classes[0] = ata_sff_dev_classify(&ap->link.device[0],
+ devmask & (1 << 0), &err);
+
+ return 0;
+}
+
+/*
+ * pata_s3c_set_devctl - Write device control register
+ */
+static void pata_s3c_set_devctl(struct ata_port *ap, u8 ctl)
+{
+ ata_outb(ap->host, ctl, ap->ioaddr.ctl_addr);
+}
+
+static struct scsi_host_template pata_s3c_sht = {
+ ATA_PIO_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations pata_s3c_port_ops = {
+ .inherits = &ata_sff_port_ops,
+ .sff_check_status = pata_s3c_check_status,
+ .sff_check_altstatus = pata_s3c_check_altstatus,
+ .sff_tf_load = pata_s3c_tf_load,
+ .sff_tf_read = pata_s3c_tf_read,
+ .sff_data_xfer = pata_s3c_data_xfer,
+ .sff_exec_command = pata_s3c_exec_command,
+ .sff_dev_select = pata_s3c_dev_select,
+ .sff_set_devctl = pata_s3c_set_devctl,
+ .softreset = pata_s3c_softreset,
+ .set_piomode = pata_s3c_set_piomode,
+};
+
+static struct ata_port_operations pata_s5p_port_ops = {
+ .inherits = &ata_sff_port_ops,
+ .set_piomode = pata_s3c_set_piomode,
+};
+
+static void pata_s3c_enable(void *s3c_ide_regbase, bool state)
+{
+ u32 temp = readl(s3c_ide_regbase + S3C_ATA_CTRL);
+ temp = state ? (temp | 1) : (temp & ~1);
+ writel(temp, s3c_ide_regbase + S3C_ATA_CTRL);
+}
+
+static irqreturn_t pata_s3c_irq(int irq, void *dev_instance)
+{
+ struct ata_host *host = dev_instance;
+ struct s3c_ide_info *info = host->private_data;
+ u32 reg;
+
+ reg = readl(info->ide_addr + S3C_ATA_IRQ);
+ writel(reg, info->ide_addr + S3C_ATA_IRQ);
+
+ return ata_sff_interrupt(irq, dev_instance);
+}
+
+static void pata_s3c_hwinit(struct s3c_ide_info *info,
+ struct s3c_ide_platdata *pdata)
+{
+ switch (info->cpu_type) {
+ case TYPE_S3C64XX:
+ /* Configure as big endian */
+ pata_s3c_cfg_mode(info->sfr_addr);
+ pata_s3c_set_endian(info->ide_addr, 1);
+ pata_s3c_enable(info->ide_addr, true);
+ msleep(100);
+
+ /* Remove IRQ Status */
+ writel(0x1f, info->ide_addr + S3C_ATA_IRQ);
+ writel(0x1b, info->ide_addr + S3C_ATA_IRQ_MSK);
+ break;
+
+ case TYPE_S5PC100:
+ pata_s3c_cfg_mode(info->sfr_addr);
+ /* FALLTHROUGH */
+
+ case TYPE_S5PV210:
+ /* Configure as little endian */
+ pata_s3c_set_endian(info->ide_addr, 0);
+ pata_s3c_enable(info->ide_addr, true);
+ msleep(100);
+
+ /* Remove IRQ Status */
+ writel(0x3f, info->ide_addr + S3C_ATA_IRQ);
+ writel(0x3f, info->ide_addr + S3C_ATA_IRQ_MSK);
+ break;
+
+ default:
+ BUG();
+ }
+}
+
+static int __init pata_s3c_probe(struct platform_device *pdev)
+{
+ struct s3c_ide_platdata *pdata = pdev->dev.platform_data;
+ struct device *dev = &pdev->dev;
+ struct s3c_ide_info *info;
+ struct resource *res;
+ struct ata_port *ap;
+ struct ata_host *host;
+ enum s3c_cpu_type cpu_type;
+ int ret;
+
+ cpu_type = platform_get_device_id(pdev)->driver_data;
+
+ info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
+ if (!info) {
+ dev_err(dev, "failed to allocate memory for device data\n");
+ return -ENOMEM;
+ }
+
+ info->irq = platform_get_irq(pdev, 0);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res == NULL) {
+ dev_err(dev, "failed to get mem resource\n");
+ return -EINVAL;
+ }
+
+ if (!devm_request_mem_region(dev, res->start,
+ resource_size(res), DRV_NAME)) {
+ dev_err(dev, "error requesting register region\n");
+ return -EBUSY;
+ }
+
+ info->ide_addr = devm_ioremap(dev, res->start, resource_size(res));
+ if (!info->ide_addr) {
+ dev_err(dev, "failed to map IO base address\n");
+ return -ENOMEM;
+ }
+
+ info->clk = clk_get(&pdev->dev, "cfcon");
+ if (IS_ERR(info->clk)) {
+ dev_err(dev, "failed to get access to cf controller clock\n");
+ ret = PTR_ERR(info->clk);
+ info->clk = NULL;
+ return ret;
+ }
+
+ clk_enable(info->clk);
+
+ /* init ata host */
+ host = ata_host_alloc(dev, 1);
+ if (!host) {
+ dev_err(dev, "failed to allocate ide host\n");
+ ret = -ENOMEM;
+ goto stop_clk;
+ }
+
+ ap = host->ports[0];
+ ap->flags |= ATA_FLAG_MMIO;
+ ap->pio_mask = ATA_PIO4;
+
+ if (cpu_type == TYPE_S3C64XX) {
+ ap->ops = &pata_s3c_port_ops;
+ info->sfr_addr = info->ide_addr + 0x1800;
+ info->ide_addr += 0x1900;
+ info->fifo_status_reg = 0x94;
+ } else if (cpu_type == TYPE_S5PC100) {
+ ap->ops = &pata_s5p_port_ops;
+ info->sfr_addr = info->ide_addr + 0x1800;
+ info->ide_addr += 0x1900;
+ info->fifo_status_reg = 0x84;
+ } else {
+ ap->ops = &pata_s5p_port_ops;
+ info->fifo_status_reg = 0x84;
+ }
+
+ info->cpu_type = cpu_type;
+
+ if (info->irq <= 0) {
+ ap->flags |= ATA_FLAG_PIO_POLLING;
+ info->irq = 0;
+ ata_port_desc(ap, "no IRQ, using PIO polling\n");
+ }
+
+ ap->ioaddr.cmd_addr = info->ide_addr + S3C_ATA_CMD;
+ ap->ioaddr.data_addr = info->ide_addr + S3C_ATA_PIO_DTR;
+ ap->ioaddr.error_addr = info->ide_addr + S3C_ATA_PIO_FED;
+ ap->ioaddr.feature_addr = info->ide_addr + S3C_ATA_PIO_FED;
+ ap->ioaddr.nsect_addr = info->ide_addr + S3C_ATA_PIO_SCR;
+ ap->ioaddr.lbal_addr = info->ide_addr + S3C_ATA_PIO_LLR;
+ ap->ioaddr.lbam_addr = info->ide_addr + S3C_ATA_PIO_LMR;
+ ap->ioaddr.lbah_addr = info->ide_addr + S3C_ATA_PIO_LHR;
+ ap->ioaddr.device_addr = info->ide_addr + S3C_ATA_PIO_DVR;
+ ap->ioaddr.status_addr = info->ide_addr + S3C_ATA_PIO_CSD;
+ ap->ioaddr.command_addr = info->ide_addr + S3C_ATA_PIO_CSD;
+ ap->ioaddr.altstatus_addr = info->ide_addr + S3C_ATA_PIO_DAD;
+ ap->ioaddr.ctl_addr = info->ide_addr + S3C_ATA_PIO_DAD;
+
+ ata_port_desc(ap, "mmio cmd 0x%llx ",
+ (unsigned long long)res->start);
+
+ host->private_data = info;
+
+ if (pdata && pdata->setup_gpio)
+ pdata->setup_gpio();
+
+ /* Set endianness and enable the interface */
+ pata_s3c_hwinit(info, pdata);
+
+ platform_set_drvdata(pdev, host);
+
+ return ata_host_activate(host, info->irq,
+ info->irq ? pata_s3c_irq : NULL,
+ 0, &pata_s3c_sht);
+
+stop_clk:
+ clk_disable(info->clk);
+ clk_put(info->clk);
+ return ret;
+}
+
+static int __exit pata_s3c_remove(struct platform_device *pdev)
+{
+ struct ata_host *host = platform_get_drvdata(pdev);
+ struct s3c_ide_info *info = host->private_data;
+
+ ata_host_detach(host);
+
+ clk_disable(info->clk);
+ clk_put(info->clk);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int pata_s3c_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct ata_host *host = platform_get_drvdata(pdev);
+
+ return ata_host_suspend(host, PMSG_SUSPEND);
+}
+
+static int pata_s3c_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct ata_host *host = platform_get_drvdata(pdev);
+ struct s3c_ide_platdata *pdata = pdev->dev.platform_data;
+ struct s3c_ide_info *info = host->private_data;
+
+ pata_s3c_hwinit(info, pdata);
+ ata_host_resume(host);
+
+ return 0;
+}
+
+static const struct dev_pm_ops pata_s3c_pm_ops = {
+ .suspend = pata_s3c_suspend,
+ .resume = pata_s3c_resume,
+};
+#endif
+
+/* driver device registration */
+static struct platform_device_id pata_s3c_driver_ids[] = {
+ {
+ .name = "s3c64xx-pata",
+ .driver_data = TYPE_S3C64XX,
+ }, {
+ .name = "s5pc100-pata",
+ .driver_data = TYPE_S5PC100,
+ }, {
+ .name = "s5pv210-pata",
+ .driver_data = TYPE_S5PV210,
+ },
+ { }
+};
+
+MODULE_DEVICE_TABLE(platform, pata_s3c_driver_ids);
+
+static struct platform_driver pata_s3c_driver = {
+ .remove = __exit_p(pata_s3c_remove),
+ .id_table = pata_s3c_driver_ids,
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &pata_s3c_pm_ops,
+#endif
+ },
+};
+
+static int __init pata_s3c_init(void)
+{
+ return platform_driver_probe(&pata_s3c_driver, pata_s3c_probe);
+}
+
+static void __exit pata_s3c_exit(void)
+{
+ platform_driver_unregister(&pata_s3c_driver);
+}
+
+module_init(pata_s3c_init);
+module_exit(pata_s3c_exit);
+
+MODULE_AUTHOR("Abhilash Kesavan, <a.kesavan at samsung.com>");
+MODULE_DESCRIPTION("low-level driver for Samsung PATA controller");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
--
1.6.2.5
More information about the linux-arm-kernel
mailing list