[PATCH] spi/omap2_mcspi: disable and enable chan between each SPI transfer
jason
jason77.wang at gmail.com
Thu Jul 1 07:58:33 EDT 2010
roman.tereshonkov at nokia.com wrote:
> Hi Jason,
>
> It is a little bit hard to analyze your logs.
> 1. You showed the bytes read in your own way but there is the data reading in omap2_mcspi_txrx_pio function also.
> 2. For your third test case. You try to read data after TX_ONLY, before triggering RX_ONLY, and get the right word.
> Looks like there is something wrong.
>
> Try to log MCSPI_CHxSTAT register to follow when RXS bit (register RX is full) is set.
> And do not use the RX register reading in you own way. If you need RX logging do it from omap2_mcspi_txrx_pio function.
>
>
> Regards
> Roman Tereshonkov
>
>
>
Hi roman,
This time i enable SPI_DEBUG first then design 3 test cases to
investigate spi issue.
test 1: print tx data, status reg(when RXS bit set) and rx data in
txrx_pio func.
test 2: revert the commit a330ce2 "omap2_mcspi: Flush posted writes",
other is same as test 1.
test 3: disable and enable channel between each SPI transfer, other is
same as test 1.
The output of test2 and test3 is same and is right, while test1's output is
wrong.
The ads7846 driver works like that, when i touch the top-left corner of the
touchscreen, it will send a READ-Y command first(8 bit word 0x93,
TX_ONLY transfer), then it will receive y coordinate(two 8 bit words, MSB
12bits are meaningful, correct data should be around 0x77nn, RX_ONLY
transfer).
the output of test1 is:
<4>======SPI MESSAGE BEGIN======
<7>ads7846 spi1.0: write-8 93
<7>ads7846 spi1.0: status reg: 00000005
<7>ads7846 spi1.0: read-8 f0
<7>ads7846 spi1.0: status reg: 00000007
<7>ads7846 spi1.0: read-8 77
<7>ads7846 spi1.0: write-8 93
<7>ads7846 spi1.0: status reg: 00000005
<7>ads7846 spi1.0: read-8 f0
<7>ads7846 spi1.0: status reg: 00000007
<7>ads7846 spi1.0: read-8 77
<4>.....SPI MESSAGE END.....
the output of test2 is:
<4>======SPI MESSAGE BEGIN======
<7>ads7846 spi1.0: write-8 93
<7>ads7846 spi1.0: status reg: 00000007
<7>ads7846 spi1.0: read-8 77
<7>ads7846 spi1.0: status reg: 00000007
<7>ads7846 spi1.0: read-8 b0
<7>ads7846 spi1.0: write-8 93
<7>ads7846 spi1.0: status reg: 00000007
<7>ads7846 spi1.0: read-8 77
<7>ads7846 spi1.0: status reg: 00000007
<7>ads7846 spi1.0: read-8 88
<4>.....SPI MESSAGE END.....
the output of test3 is:
<4>======SPI MESSAGE BEGIN======
<7>ads7846 spi1.0: write-8 93
<7>ads7846 spi1.0: status reg: 00000007
<7>ads7846 spi1.0: read-8 77
<7>ads7846 spi1.0: status reg: 00000007
<7>ads7846 spi1.0: read-8 68
<7>ads7846 spi1.0: write-8 93
<7>ads7846 spi1.0: status reg: 00000007
<7>ads7846 spi1.0: read-8 77
<7>ads7846 spi1.0: status reg: 00000007
<7>ads7846 spi1.0: read-8 98
<4>.....SPI MESSAGE END.....
test1 patch:
Subject: [PATCH] SPI/test1: print tx data & rx data when ads7846 works
when we touch the top-left corner of the touchscreen, the ads7846
driver will send a read-y command(one 8-bit word, 0x93) and receive
y coordinate(two 8-bit words, MSB 12bits are meaningful). now print
all tx word, staus reg and rx word when RXS bit is set. Test1 only
add debug output and have no other modification.
Signed-off-by: Jason Wang <jason77.wang at gmail.com>
---
drivers/spi/omap2_mcspi.c | 11 +++++++++--
1 files changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c
index b3a94ca..893a124 100644
--- a/drivers/spi/omap2_mcspi.c
+++ b/drivers/spi/omap2_mcspi.c
@@ -40,6 +40,8 @@
#include <plat/clock.h>
#include <plat/mcspi.h>
+#define VERBOSE
+
#define OMAP2_MCSPI_MAX_FREQ 48000000
/* OMAP2 has 3 SPI controllers, while OMAP3 has 4 */
@@ -502,6 +504,11 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct
spi_transfer *xfer)
goto out;
}
+#ifdef VERBOSE
+ dev_dbg(&spi->dev, "status reg: %08x\n",
+ __raw_readl(chstat_reg));
+#endif
+
if (c == 1 && tx == NULL &&
(l & OMAP2_MCSPI_CHCONF_TURBO)) {
omap2_mcspi_set_enable(spi, 0);
@@ -893,7 +900,7 @@ static void omap2_mcspi_work(struct work_struct *work)
spi = m->spi;
cs = spi->controller_state;
cd = spi->controller_data;
-
+ printk("======SPI MESSAGE BEGIN======\n");
omap2_mcspi_set_enable(spi, 1);
list_for_each_entry(t, &m->transfers, transfer_list) {
if (t->tx_buf == NULL && t->rx_buf == NULL && t->len) {
@@ -971,7 +978,7 @@ static void omap2_mcspi_work(struct work_struct *work)
omap2_mcspi_force_cs(spi, 0);
omap2_mcspi_set_enable(spi, 0);
-
+ printk(".....SPI MESSAGE END.....\n");
m->status = status;
m->complete(m->context);
--
1.5.6.5
test2 patch:
Subject: [PATCH] SPI/test2: print tx data & rx data when ads7846 works
when we touch the top-left corner of the touchscreen, the ads7846
driver will send a read-y command(one 8-bit word, 0x93) and receive
y coordinate(two 8-bit words, MSB 12bits are meaningful). now print
all tx word and rx word. In test2, i revert the commit a330ce2
"omap2_mcspi: Flush posted writes".
Signed-off-by: Jason Wang <jason77.wang at gmail.com>
---
drivers/spi/omap2_mcspi.c | 13 ++++++++++---
1 files changed, 10 insertions(+), 3 deletions(-)
diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c
index b3a94ca..cf8066e 100644
--- a/drivers/spi/omap2_mcspi.c
+++ b/drivers/spi/omap2_mcspi.c
@@ -40,6 +40,8 @@
#include <plat/clock.h>
#include <plat/mcspi.h>
+#define VERBOSE
+
#define OMAP2_MCSPI_MAX_FREQ 48000000
/* OMAP2 has 3 SPI controllers, while OMAP3 has 4 */
@@ -204,7 +206,7 @@ static inline void mcspi_write_chconf0(const struct
spi_device *spi, u32 val)
cs->chconf0 = val;
mcspi_write_cs_reg(spi, OMAP2_MCSPI_CHCONF0, val);
- mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHCONF0);
+ /* mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHCONF0); */
}
static void omap2_mcspi_set_dma_req(const struct spi_device *spi,
@@ -502,6 +504,11 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct
spi_transfer *xfer)
goto out;
}
+#ifdef VERBOSE
+ dev_dbg(&spi->dev, "status reg: %08x\n",
+ __raw_readl(chstat_reg));
+#endif
+
if (c == 1 && tx == NULL &&
(l & OMAP2_MCSPI_CHCONF_TURBO)) {
omap2_mcspi_set_enable(spi, 0);
@@ -893,7 +900,7 @@ static void omap2_mcspi_work(struct work_struct *work)
spi = m->spi;
cs = spi->controller_state;
cd = spi->controller_data;
-
+ printk("======SPI MESSAGE BEGIN======\n");
omap2_mcspi_set_enable(spi, 1);
list_for_each_entry(t, &m->transfers, transfer_list) {
if (t->tx_buf == NULL && t->rx_buf == NULL && t->len) {
@@ -971,7 +978,7 @@ static void omap2_mcspi_work(struct work_struct *work)
omap2_mcspi_force_cs(spi, 0);
omap2_mcspi_set_enable(spi, 0);
-
+ printk(".....SPI MESSAGE END.....\n");
m->status = status;
m->complete(m->context);
--
1.5.6.5
test3 patch:
Subject: [PATCH] SPI/test3: print tx data & rx data when ads7846 works
when we touch the top-left corner of the touchscreen, the ads7846
driver will send a read-y command(one 8-bit word, 0x93) and receive
y coordinate(two 8-bit words, MSB 12bits are meaningful). now print
all tx word and rx word. In test3, i add disable channel and reenable
channel between each SPI transfer.
Signed-off-by: Jason Wang <jason77.wang at gmail.com>
---
drivers/spi/omap2_mcspi.c | 21 +++++++++++++++------
1 files changed, 15 insertions(+), 6 deletions(-)
diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c
index b3a94ca..7449365 100644
--- a/drivers/spi/omap2_mcspi.c
+++ b/drivers/spi/omap2_mcspi.c
@@ -40,6 +40,8 @@
#include <plat/clock.h>
#include <plat/mcspi.h>
+#define VERBOSE
+
#define OMAP2_MCSPI_MAX_FREQ 48000000
/* OMAP2 has 3 SPI controllers, while OMAP3 has 4 */
@@ -408,7 +410,6 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct
spi_transfer *xfer)
count -= (word_len <= 8) ? 2 :
(word_len <= 16) ? 4 :
/* word_len <= 32 */ 8;
- omap2_mcspi_set_enable(spi, 1);
return count;
}
}
@@ -430,8 +431,10 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct
spi_transfer *xfer)
(word_len <= 16) ? 2 :
/* word_len <= 32 */ 4;
}
- omap2_mcspi_set_enable(spi, 1);
}
+
+ omap2_mcspi_set_enable(spi, 0);
+
return count;
}
@@ -502,6 +505,11 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct
spi_transfer *xfer)
goto out;
}
+#ifdef VERBOSE
+ dev_dbg(&spi->dev, "status reg: %08x\n",
+ __raw_readl(chstat_reg));
+#endif
+
if (c == 1 && tx == NULL &&
(l & OMAP2_MCSPI_CHCONF_TURBO)) {
omap2_mcspi_set_enable(spi, 0);
@@ -646,7 +654,7 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct
spi_transfer *xfer)
dev_err(&spi->dev, "EOT timed out\n");
}
out:
- omap2_mcspi_set_enable(spi, 1);
+ omap2_mcspi_set_enable(spi, 0);
return count - c;
}
@@ -893,8 +901,7 @@ static void omap2_mcspi_work(struct work_struct *work)
spi = m->spi;
cs = spi->controller_state;
cd = spi->controller_data;
-
- omap2_mcspi_set_enable(spi, 1);
+ printk("======SPI MESSAGE BEGIN======\n");
list_for_each_entry(t, &m->transfers, transfer_list) {
if (t->tx_buf == NULL && t->rx_buf == NULL && t->len) {
status = -EINVAL;
@@ -931,6 +938,8 @@ static void omap2_mcspi_work(struct work_struct *work)
mcspi_write_chconf0(spi, chconf);
+ omap2_mcspi_set_enable(spi, 1);
+
if (t->len) {
unsigned count;
@@ -971,7 +980,7 @@ static void omap2_mcspi_work(struct work_struct *work)
omap2_mcspi_force_cs(spi, 0);
omap2_mcspi_set_enable(spi, 0);
-
+ printk(".....SPI MESSAGE END.....\n");
m->status = status;
m->complete(m->context);
--
1.5.6.5
More information about the linux-arm-kernel
mailing list