usb host port3 on pxa310?

[Igor Grinberg]

 On 08/22/10 11:20, Chen Wenjie wrote:
> Hi, Igor and all,
>
> 	Thank you very much for giving me such valuable help.
>
> 	Now I have upgrade the ohci part (drivers/usb/host/ohci-pxa270.c ..)
> to 2.6.29. (I am failed on upgrade the total branch from 2.6.27 to 2.6.29 :(  )
>
> 	But the problem still exist. 
>  (the isp1105 was really assembled; and  the GPIO pins are initialized with 
>  pxa3xx_mfp_config() ).
>
> when I insert a usb-disk, it output 
> -----------------------------------------------------------------------------------------
> usb 1-3: new full speed USB device using pxa27x-ohci and address 2
> usb 1-3: device descriptor read/64, error -62
> usb 1-3: device descriptor read/64, error -62
> usb 1-3: new full speed USB device using pxa27x-ohci and address 3
> usb 1-3: device descriptor read/64, error -62
> usb 1-3: device descriptor read/64, error -62
> usb 1-3: new full speed USB device using pxa27x-ohci and address 4
> usb 1-3: device not accepting address 4, error -62
> usb 1-3: new full speed USB device using pxa27x-ohci and address 5
> usb 1-3: device not accepting address 5, error -62
> hub 1-0:1.0: unable to enumerate USB device on port 3
> ----------------------------------------------------------------------------------------
>
>
> and dmesg shows this info continuesly.:
> hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
> hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
> ...
> hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
>
>
>
> a detailed log file is attached.
>
>
> Is there any hardware problem?
> maybe the connection of ISP1105 was wrong.

Indeed, this can be a h/w problem.

> and I found the VCC voltage is only 3.0v, it is lower than 3.3v
> (in the spec). Is this a fatal issue?

May be not fatal, but could bring issues...
I'd check the VBUS on that usb port and also the pull ups on DP/DM.
If those are not by the spec. then the chances of getting it work are poor.

> Thank you very much!
>
>
> ------------------				 
> Chen Wenjie
> 2010-08-22
>
> -------------------------------------------------------------
> From：Igor Grinberg
> Date：2010-08-08 14:03:02
> To：Chen Wenjie
> CC：linux-arm-kernel
> Subject：Re: usb host port3 on pxa310?
>
> On 08/08/10 04:21, Chen Wenjie wrote:
>> Hi, Igor,
>> Thank you very much for your warm and professional help!
>> I will try to upgrade the codes for ohci-pxa27x first.
>>> Do you really have sl811 and r8a66597 usb host controllers on your
>> board?
>> I think no real IC installed on my board, I just configure it on
>> menuconfig by choose something
>> seems related to USB (--blindly)
> I'd rather remove the unused drivers from the configuration,
> then have them built-in and do something with the missing hardware...
>
>> Actually, my board use a ISP1105 as the PHY interface，the schematic is :
>> http://picasaweb.google.com/114830881710721561783/Public#5502732460750351090
>>
> As far as I know DNP, stands for "Do Not Populate".
> It states: "ISP1105BS(DNP)" - is it assembled at all?
>
>> Do you think there is anything wrong?
>> GPIO setting is :
>> //file: mfp-pxa300.h
>> /* USB P3 */
>> #define GPIO77_USB_P3_1 MFP_CFG(GPIO77, AF2)
>> #define GPIO78_USB_P3_2 MFP_CFG(GPIO78, AF2)
>> #define GPIO79_USB_P3_3 MFP_CFG(GPIO79, AF2)
>> #define GPIO80_USB_P3_4 MFP_CFG(GPIO80, AF2)
>> #define GPIO81_USB_P3_5 MFP_CFG(GPIO81, AF2)
>> #define GPIO82_USB_P3_6 MFP_CFG(GPIO82, AF2)
>> #define GPIO126_USB_SPEED MFP_CFG_LPM(GPIO126, AF5, PULL_HIGH)
> Indeed, those are the defines, but you need to do the actual configuration
> for them, by calling pxa3xx_mfp_config() with appropriate parameters.
>
>> I will upgrade the driver and test it again.
>> Thank you very very much!
>> 2010-08-08
>> ------------------------------------------------------------------------
>> Chen Wenjie
>> ------------------------------------------------------------------------
>> *发件人：* Igor Grinberg
>> *发送时间：* 2010-08-07 21:42:57
>> *收件人：* Chen Wenjie
>> *抄送：* linux-arm-kernel
>> *主题：* Re: usb host port3 on pxa310?
>> On 08/06/10 21:43, Chen Wenjie wrote:
>>> I want to use PXA310 to realize a USB HOST.
>>>
>>> (My kernel version: 2.6.27)
>>>
>> There was a relatively big change in ohci-pxa27x driver, I think
>> around 2.6.28-rc1. May be you should consider upgrading...
>>> Zylonite have implemented a USB host through USBH_N(USBH1_N)
>> USBH_P(USBH1_P).
>>> Unfortunatly, In PXA310, the pins of USBH1_N and USBH1_P does not exist.
>>>
>>> So I have to use "usb host port3 " described in the manual "Vol. IV:
>> Monahans
>>> L Processor and
>>> Monahans LV Processor Developers Manual"
>>>
>>>
>>>
>>> GPIO
>>> Alternate
>>> Function
>>> Port UP3OCR[CFG]
>>> 0x0 0x2
>>> USB_P3_1 UHC Rx Data (RCV - in) — UHC Rx Data (RCV -
>>> out) —
>>> USB_P3_2 UHC OE (OE_n - out) — UHC OE (OE_n - in)
>>> —
>>> USB_P3_3 UHC Rx D– (VM - in) — UHC Rx D- (VM -
>>> out) —
>>> USB_P3_4 UHC Tx D– (VMO - out) — UHC Tx D- (VMO -
>>> in) —
>>> USB_P3_5 UHC Rx D+ (VP - in) — UHC Rx D+ (VP -
>>> out) —
>>> USB_P3_6 UHC Tx D+ (VPO - out) — UHC Tx D+ (VPO -
>>> in) —
>>>
>>> In the schematic, I have connected GPIO77~82 to USB_P3_1 ~ USB_P3_6.
>>>
>> You need also to configure those gpios to alternate function 2 in the
>> MFPRs.
>> If you use a transceiver mode, then may be you need USBHPEN signal
>> connected to your PHY and configured accordingly in MFPR.
>> Also, in pxa310 there is a U2DP3CR register, which controls output
>> and serial mode selection of the usb port3.
>>>
>>> However, The USB port 3 does not work.
>>> Here is the log:
>>>
>>> ======================================
>>> pxa27x-ohci pxa27x-ohci: PXA27x OHCI
>>> pxa27x-ohci pxa27x-ohci: new USB bus registered, assigned bus number 1
>>> pxa27x-ohci pxa27x-ohci: irq 3, io mem 0x4c000000
>>> usb usb1: configuration #1 chosen from 1 choice
>>> hub 1-0:1.0: USB hub found
>>> hub 1-0:1.0: 3 ports detected
>>> usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
>>> usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>>> usb usb1: Product: PXA27x OHCI
>>> usb usb1: Manufacturer: Linux 2.6.27-dirty ohci_hcd
>>> usb usb1: SerialNumber: pxa27x
>>> sl811: driver sl811-hcd, 19 May 2005
>>> r8a66597_hcd: driver r8a66597_hcd, 10 Apr 2008
>>>
>> Do you really have sl811 and r8a66597 usb host controllers on your board?
>>> usb 1-3: new full speed USB device using pxa27x-ohci and address 2
>>> usb 1-3: device descriptor read/64, error -62
>>> usb 1-3: device descriptor read/64, error -62
>>> usb 1-3: new full speed USB device using pxa27x-ohci and address 3
>>> usb 1-3: device descriptor read/64, error -62
>>> usb 1-3: device descriptor read/64, error -62
>>> usb 1-3: new full speed USB device using pxa27x-ohci and address 4
>>> usb 1-3: device not accepting address 4, error -62
>>> usb 1-3: new full speed USB device using pxa27x-ohci and address 5
>>> usb 1-3: device not accepting address 5, error -62
>>> hub 1-0:1.0: unable to enumerate USB device on port 3
>>> ======================================
>>>
>>>
>>> Then I found a bit in UP2OCR -- (VPMBlockEnbN).
>>> It is quite strange (if not ugly:( ) the this bit is to control port 3
>>> (In UP2OCR--a register for port 2, while there is too many unused
>> bits in
>>> UP3OCR)
>>>
>>> But I am not very sure how to use this bit.
>>> I grep the source tree, but found nothing about VPMBlockEnbN.
>>>
>>>
>>> Can anyone tell me that how to write a driver for USB-host-port-3?
>>>
>> As far as I know pxa310 usb port3 does not need any special driver
>> to work in host mode, ohci-pxa27x is enough.
>> Currently, the setup of registers, which are not related to UHC
>> (UP2OCR, UP3OCR, etc.), is done in the board code, in the ohci
>> callback.
>>> High appreciation for your kind help!
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> linux-arm-kernel mailing list
>>> linux-arm-kernel at lists.infradead.org
>>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>>>
>> -- 
>> Regards,
>> Igor.

-- 
Regards,
Igor.