[PATCH 02/11] [ARM] pxa/palm: Flip Palm LD,TX,T5,Z72 to Palm27x
Marek Vasut
marek.vasut at gmail.com
Wed Aug 4 07:22:04 EDT 2010
Signed-off-by: Marek Vasut <marek.vasut at gmail.com>
---
arch/arm/mach-pxa/Kconfig | 4 +
arch/arm/mach-pxa/palmld.c | 291 +++++++----------------------------
arch/arm/mach-pxa/palmt5.c | 282 ++++------------------------------
arch/arm/mach-pxa/palmtreo.c | 355 +++++++-----------------------------------
arch/arm/mach-pxa/palmtx.c | 298 ++++++------------------------------
arch/arm/mach-pxa/palmz72.c | 266 +++----------------------------
6 files changed, 215 insertions(+), 1281 deletions(-)
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index 6f04f21..7aefb90 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -374,6 +374,7 @@ config MACH_PALMT5
depends on ARCH_PXA_PALM
select PXA27x
select IWMMXT
+ select MACH_PALM27X
help
Say Y here if you intend to run this kernel on a Palm Tungsten|T5
handheld computer.
@@ -384,6 +385,7 @@ config MACH_PALMTX
depends on ARCH_PXA_PALM
select PXA27x
select IWMMXT
+ select MACH_PALM27X
help
Say Y here if you intend to run this kernel on a Palm T|X
handheld computer.
@@ -394,6 +396,7 @@ config MACH_PALMZ72
depends on ARCH_PXA_PALM
select PXA27x
select IWMMXT
+ select MACH_PALM27X
help
Say Y here if you intend to run this kernel on Palm Zire 72
handheld computer.
@@ -404,6 +407,7 @@ config MACH_PALMLD
depends on ARCH_PXA_PALM
select PXA27x
select IWMMXT
+ select MACH_PALM27X
help
Say Y here if you intend to run this kernel on a Palm LifeDrive
handheld computer.
diff --git a/arch/arm/mach-pxa/palmld.c b/arch/arm/mach-pxa/palmld.c
index 83a1a55..91038ee 100644
--- a/arch/arm/mach-pxa/palmld.c
+++ b/arch/arm/mach-pxa/palmld.c
@@ -41,6 +41,7 @@
#include <mach/irda.h>
#include <mach/pxa27x_keypad.h>
#include <mach/palmasoc.h>
+#include <mach/palm27x.h>
#include "generic.h"
#include "devices.h"
@@ -127,6 +128,7 @@ static unsigned long palmld_pin_config[] __initdata = {
/******************************************************************************
* NOR Flash
******************************************************************************/
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
static struct mtd_partition palmld_partitions[] = {
{
.name = "Flash",
@@ -160,20 +162,18 @@ static struct platform_device palmld_flash = {
},
};
-/******************************************************************************
- * SD/MMC card controller
- ******************************************************************************/
-static struct pxamci_platform_data palmld_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_card_detect = GPIO_NR_PALMLD_SD_DETECT_N,
- .gpio_card_ro = GPIO_NR_PALMLD_SD_READONLY,
- .gpio_power = GPIO_NR_PALMLD_SD_POWER,
- .detect_delay_ms = 200,
-};
+static void __init palmld_nor_init(void)
+{
+ platform_device_register(&palmld_flash);
+}
+#else
+static inline void palmld_nor_init(void) {}
+#endif
/******************************************************************************
* GPIO keyboard
******************************************************************************/
+#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULE)
static unsigned int palmld_matrix_keys[] = {
KEY(0, 1, KEY_F2),
KEY(0, 2, KEY_UP),
@@ -200,9 +200,18 @@ static struct pxa27x_keypad_platform_data palmld_keypad_platform_data = {
.debounce_interval = 30,
};
+static void __init palmld_kpc_init(void)
+{
+ pxa_set_keypad_info(&palmld_keypad_platform_data);
+}
+#else
+static inline void palmld_kpc_init(void) {}
+#endif
+
/******************************************************************************
* GPIO keys
******************************************************************************/
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
static struct gpio_keys_button palmld_pxa_buttons[] = {
{KEY_F8, GPIO_NR_PALMLD_HOTSYNC_BUTTON_N, 1, "HotSync Button" },
{KEY_F9, GPIO_NR_PALMLD_LOCK_SWITCH, 0, "Lock Switch" },
@@ -222,77 +231,18 @@ static struct platform_device palmld_pxa_keys = {
},
};
-/******************************************************************************
- * Backlight
- ******************************************************************************/
-static int palmld_backlight_init(struct device *dev)
-{
- int ret;
-
- ret = gpio_request(GPIO_NR_PALMLD_BL_POWER, "BL POWER");
- if (ret)
- goto err;
- ret = gpio_direction_output(GPIO_NR_PALMLD_BL_POWER, 0);
- if (ret)
- goto err2;
- ret = gpio_request(GPIO_NR_PALMLD_LCD_POWER, "LCD POWER");
- if (ret)
- goto err2;
- ret = gpio_direction_output(GPIO_NR_PALMLD_LCD_POWER, 0);
- if (ret)
- goto err3;
-
- return 0;
-err3:
- gpio_free(GPIO_NR_PALMLD_LCD_POWER);
-err2:
- gpio_free(GPIO_NR_PALMLD_BL_POWER);
-err:
- return ret;
-}
-
-static int palmld_backlight_notify(struct device *dev, int brightness)
+static void __init palmld_keys_init(void)
{
- gpio_set_value(GPIO_NR_PALMLD_BL_POWER, brightness);
- gpio_set_value(GPIO_NR_PALMLD_LCD_POWER, brightness);
- return brightness;
+ platform_device_register(&palmld_pxa_keys);
}
-
-static void palmld_backlight_exit(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMLD_BL_POWER);
- gpio_free(GPIO_NR_PALMLD_LCD_POWER);
-}
-
-static struct platform_pwm_backlight_data palmld_backlight_data = {
- .pwm_id = 0,
- .max_brightness = PALMLD_MAX_INTENSITY,
- .dft_brightness = PALMLD_MAX_INTENSITY,
- .pwm_period_ns = PALMLD_PERIOD_NS,
- .init = palmld_backlight_init,
- .notify = palmld_backlight_notify,
- .exit = palmld_backlight_exit,
-};
-
-static struct platform_device palmld_backlight = {
- .name = "pwm-backlight",
- .dev = {
- .parent = &pxa27x_device_pwm0.dev,
- .platform_data = &palmld_backlight_data,
- },
-};
-
-/******************************************************************************
- * IrDA
- ******************************************************************************/
-static struct pxaficp_platform_data palmld_ficp_platform_data = {
- .gpio_pwdown = GPIO_NR_PALMLD_IR_DISABLE,
- .transceiver_cap = IR_SIRMODE | IR_OFF,
-};
+#else
+static inline void palmld_keys_init(void) {}
+#endif
/******************************************************************************
* LEDs
******************************************************************************/
+#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
struct gpio_led gpio_leds[] = {
{
.name = "palmld:green:led",
@@ -318,176 +268,34 @@ static struct platform_device palmld_leds = {
}
};
-/******************************************************************************
- * Power supply
- ******************************************************************************/
-static int power_supply_init(struct device *dev)
-{
- int ret;
-
- ret = gpio_request(GPIO_NR_PALMLD_POWER_DETECT, "CABLE_STATE_AC");
- if (ret)
- goto err1;
- ret = gpio_direction_input(GPIO_NR_PALMLD_POWER_DETECT);
- if (ret)
- goto err2;
-
- ret = gpio_request(GPIO_NR_PALMLD_USB_DETECT_N, "CABLE_STATE_USB");
- if (ret)
- goto err2;
- ret = gpio_direction_input(GPIO_NR_PALMLD_USB_DETECT_N);
- if (ret)
- goto err3;
-
- return 0;
-
-err3:
- gpio_free(GPIO_NR_PALMLD_USB_DETECT_N);
-err2:
- gpio_free(GPIO_NR_PALMLD_POWER_DETECT);
-err1:
- return ret;
-}
-
-static int palmld_is_ac_online(void)
+static void __init palmld_leds_init(void)
{
- return gpio_get_value(GPIO_NR_PALMLD_POWER_DETECT);
+ platform_device_register(&palmld_leds);
}
-
-static int palmld_is_usb_online(void)
-{
- return !gpio_get_value(GPIO_NR_PALMLD_USB_DETECT_N);
-}
-
-static void power_supply_exit(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMLD_USB_DETECT_N);
- gpio_free(GPIO_NR_PALMLD_POWER_DETECT);
-}
-
-static char *palmld_supplicants[] = {
- "main-battery",
-};
-
-static struct pda_power_pdata power_supply_info = {
- .init = power_supply_init,
- .is_ac_online = palmld_is_ac_online,
- .is_usb_online = palmld_is_usb_online,
- .exit = power_supply_exit,
- .supplied_to = palmld_supplicants,
- .num_supplicants = ARRAY_SIZE(palmld_supplicants),
-};
-
-static struct platform_device power_supply = {
- .name = "pda-power",
- .id = -1,
- .dev = {
- .platform_data = &power_supply_info,
- },
-};
-
-/******************************************************************************
- * WM97xx audio, battery
- ******************************************************************************/
-static struct wm97xx_batt_pdata palmld_batt_pdata = {
- .batt_aux = WM97XX_AUX_ID3,
- .temp_aux = WM97XX_AUX_ID2,
- .charge_gpio = -1,
- .max_voltage = PALMLD_BAT_MAX_VOLTAGE,
- .min_voltage = PALMLD_BAT_MIN_VOLTAGE,
- .batt_mult = 1000,
- .batt_div = 414,
- .temp_mult = 1,
- .temp_div = 1,
- .batt_tech = POWER_SUPPLY_TECHNOLOGY_LIPO,
- .batt_name = "main-batt",
-};
-
-static struct wm97xx_pdata palmld_wm97xx_pdata = {
- .batt_pdata = &palmld_batt_pdata,
-};
-
-static pxa2xx_audio_ops_t palmld_ac97_pdata = {
- .reset_gpio = 95,
- .codec_pdata = { &palmld_wm97xx_pdata, },
-};
-
-static struct palm27x_asoc_info palmld_asoc_pdata = {
- .jack_gpio = GPIO_NR_PALMLD_EARPHONE_DETECT,
-};
-
-static struct platform_device palmld_asoc = {
- .name = "palm27x-asoc",
- .id = -1,
- .dev = {
- .platform_data = &palmld_asoc_pdata,
- },
-};
+#else
+static inline void palmld_leds_init(void) {}
+#endif
/******************************************************************************
* HDD
******************************************************************************/
-static struct platform_device palmld_hdd = {
+#if defined(CONFIG_PATA_PALMLD) || defined(CONFIG_PATA_PALMLD_MODULE)
+static struct platform_device palmld_ide_device = {
.name = "pata_palmld",
.id = -1,
};
-/******************************************************************************
- * Framebuffer
- ******************************************************************************/
-static struct pxafb_mode_info palmld_lcd_modes[] = {
-{
- .pixclock = 57692,
- .xres = 320,
- .yres = 480,
- .bpp = 16,
-
- .left_margin = 32,
- .right_margin = 1,
- .upper_margin = 7,
- .lower_margin = 1,
-
- .hsync_len = 4,
- .vsync_len = 1,
-},
-};
-
-static struct pxafb_mach_info palmld_lcd_screen = {
- .modes = palmld_lcd_modes,
- .num_modes = ARRAY_SIZE(palmld_lcd_modes),
- .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
-};
-
-/******************************************************************************
- * Power management - standby
- ******************************************************************************/
-static void __init palmld_pm_init(void)
+static void __init palmld_ide_init(void)
{
- static u32 resume[] = {
- 0xe3a00101, /* mov r0, #0x40000000 */
- 0xe380060f, /* orr r0, r0, #0x00f00000 */
- 0xe590f008, /* ldr pc, [r0, #0x08] */
- };
-
- /* copy the bootloader */
- memcpy(phys_to_virt(PALMLD_STR_BASE), resume, sizeof(resume));
+ platform_device_register(&palmld_ide_device);
}
+#else
+static inline void palmld_ide_init(void) {}
+#endif
/******************************************************************************
* Machine init
******************************************************************************/
-static struct platform_device *devices[] __initdata = {
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
- &palmld_pxa_keys,
-#endif
- &palmld_backlight,
- &palmld_leds,
- &power_supply,
- &palmld_asoc,
- &palmld_hdd,
- &palmld_flash,
-};
-
static struct map_desc palmld_io_desc[] __initdata = {
{
.virtual = PALMLD_IDE_VIRT,
@@ -512,19 +320,26 @@ static void __init palmld_map_io(void)
static void __init palmld_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(palmld_pin_config));
-
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
- palmld_pm_init();
- set_pxa_fb_info(&palmld_lcd_screen);
- pxa_set_mci_info(&palmld_mci_platform_data);
- pxa_set_ac97_info(&palmld_ac97_pdata);
- pxa_set_ficp_info(&palmld_ficp_platform_data);
- pxa_set_keypad_info(&palmld_keypad_platform_data);
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
+ palm27x_mmc_init(GPIO_NR_PALMLD_SD_DETECT_N, GPIO_NR_PALMLD_SD_READONLY,
+ GPIO_NR_PALMLD_SD_POWER, 0);
+ palm27x_pm_init(PALMLD_STR_BASE);
+ palm27x_lcd_init(-1, &palm_320x480_lcd_mode);
+ palm27x_irda_init(GPIO_NR_PALMLD_IR_DISABLE);
+ palm27x_ac97_init(PALMLD_BAT_MIN_VOLTAGE, PALMLD_BAT_MAX_VOLTAGE,
+ GPIO_NR_PALMLD_EARPHONE_DETECT, 95);
+ palm27x_pwm_init(GPIO_NR_PALMLD_BL_POWER, GPIO_NR_PALMLD_LCD_POWER);
+ palm27x_power_init(GPIO_NR_PALMLD_POWER_DETECT,
+ GPIO_NR_PALMLD_USB_DETECT_N);
+ palm27x_pmic_init();
+ palmld_kpc_init();
+ palmld_keys_init();
+ palmld_nor_init();
+ palmld_leds_init();
+ palmld_ide_init();
}
MACHINE_START(PALMLD, "Palm LifeDrive")
diff --git a/arch/arm/mach-pxa/palmt5.c b/arch/arm/mach-pxa/palmt5.c
index 0b36d7d..731ee7b 100644
--- a/arch/arm/mach-pxa/palmt5.c
+++ b/arch/arm/mach-pxa/palmt5.c
@@ -41,6 +41,7 @@
#include <mach/pxa27x_keypad.h>
#include <mach/udc.h>
#include <mach/palmasoc.h>
+#include <mach/palm27x.h>
#include "generic.h"
#include "devices.h"
@@ -103,19 +104,9 @@ static unsigned long palmt5_pin_config[] __initdata = {
};
/******************************************************************************
- * SD/MMC card controller
- ******************************************************************************/
-static struct pxamci_platform_data palmt5_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_card_detect = GPIO_NR_PALMT5_SD_DETECT_N,
- .gpio_card_ro = GPIO_NR_PALMT5_SD_READONLY,
- .gpio_power = GPIO_NR_PALMT5_SD_POWER,
- .detect_delay_ms = 200,
-};
-
-/******************************************************************************
* GPIO keyboard
******************************************************************************/
+#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULE)
static unsigned int palmt5_matrix_keys[] = {
KEY(0, 0, KEY_POWER),
KEY(0, 1, KEY_F1),
@@ -141,9 +132,18 @@ static struct pxa27x_keypad_platform_data palmt5_keypad_platform_data = {
.debounce_interval = 30,
};
+static void __init palmt5_kpc_init(void)
+{
+ pxa_set_keypad_info(&palmt5_keypad_platform_data);
+}
+#else
+static inline void palmt5_kpc_init(void) {}
+#endif
+
/******************************************************************************
* GPIO keys
******************************************************************************/
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
static struct gpio_keys_button palmt5_pxa_buttons[] = {
{KEY_F8, GPIO_NR_PALMT5_HOTSYNC_BUTTON_N, 1, "HotSync Button" },
};
@@ -161,260 +161,38 @@ static struct platform_device palmt5_pxa_keys = {
},
};
-/******************************************************************************
- * Backlight
- ******************************************************************************/
-static int palmt5_backlight_init(struct device *dev)
-{
- int ret;
-
- ret = gpio_request(GPIO_NR_PALMT5_BL_POWER, "BL POWER");
- if (ret)
- goto err;
- ret = gpio_direction_output(GPIO_NR_PALMT5_BL_POWER, 0);
- if (ret)
- goto err2;
- ret = gpio_request(GPIO_NR_PALMT5_LCD_POWER, "LCD POWER");
- if (ret)
- goto err2;
- ret = gpio_direction_output(GPIO_NR_PALMT5_LCD_POWER, 0);
- if (ret)
- goto err3;
-
- return 0;
-err3:
- gpio_free(GPIO_NR_PALMT5_LCD_POWER);
-err2:
- gpio_free(GPIO_NR_PALMT5_BL_POWER);
-err:
- return ret;
-}
-
-static int palmt5_backlight_notify(struct device *dev, int brightness)
-{
- gpio_set_value(GPIO_NR_PALMT5_BL_POWER, brightness);
- gpio_set_value(GPIO_NR_PALMT5_LCD_POWER, brightness);
- return brightness;
-}
-
-static void palmt5_backlight_exit(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMT5_BL_POWER);
- gpio_free(GPIO_NR_PALMT5_LCD_POWER);
-}
-
-static struct platform_pwm_backlight_data palmt5_backlight_data = {
- .pwm_id = 0,
- .max_brightness = PALMT5_MAX_INTENSITY,
- .dft_brightness = PALMT5_MAX_INTENSITY,
- .pwm_period_ns = PALMT5_PERIOD_NS,
- .init = palmt5_backlight_init,
- .notify = palmt5_backlight_notify,
- .exit = palmt5_backlight_exit,
-};
-
-static struct platform_device palmt5_backlight = {
- .name = "pwm-backlight",
- .dev = {
- .parent = &pxa27x_device_pwm0.dev,
- .platform_data = &palmt5_backlight_data,
- },
-};
-
-/******************************************************************************
- * IrDA
- ******************************************************************************/
-static struct pxaficp_platform_data palmt5_ficp_platform_data = {
- .gpio_pwdown = GPIO_NR_PALMT5_IR_DISABLE,
- .transceiver_cap = IR_SIRMODE | IR_OFF,
-};
-
-/******************************************************************************
- * UDC
- ******************************************************************************/
-static struct gpio_vbus_mach_info palmt5_udc_info = {
- .gpio_vbus = GPIO_NR_PALMT5_USB_DETECT_N,
- .gpio_vbus_inverted = 1,
- .gpio_pullup = GPIO_NR_PALMT5_USB_PULLUP,
-};
-
-static struct platform_device palmt5_gpio_vbus = {
- .name = "gpio-vbus",
- .id = -1,
- .dev = {
- .platform_data = &palmt5_udc_info,
- },
-};
-
-/******************************************************************************
- * Power supply
- ******************************************************************************/
-static int power_supply_init(struct device *dev)
-{
- int ret;
-
- ret = gpio_request(GPIO_NR_PALMT5_POWER_DETECT, "CABLE_STATE_AC");
- if (ret)
- goto err1;
- ret = gpio_direction_input(GPIO_NR_PALMT5_POWER_DETECT);
- if (ret)
- goto err2;
-
- return 0;
-err2:
- gpio_free(GPIO_NR_PALMT5_POWER_DETECT);
-err1:
- return ret;
-}
-
-static int palmt5_is_ac_online(void)
-{
- return gpio_get_value(GPIO_NR_PALMT5_POWER_DETECT);
-}
-
-static void power_supply_exit(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMT5_POWER_DETECT);
-}
-
-static char *palmt5_supplicants[] = {
- "main-battery",
-};
-
-static struct pda_power_pdata power_supply_info = {
- .init = power_supply_init,
- .is_ac_online = palmt5_is_ac_online,
- .exit = power_supply_exit,
- .supplied_to = palmt5_supplicants,
- .num_supplicants = ARRAY_SIZE(palmt5_supplicants),
-};
-
-static struct platform_device power_supply = {
- .name = "pda-power",
- .id = -1,
- .dev = {
- .platform_data = &power_supply_info,
- },
-};
-
-/******************************************************************************
- * WM97xx audio, battery
- ******************************************************************************/
-static struct wm97xx_batt_pdata palmt5_batt_pdata = {
- .batt_aux = WM97XX_AUX_ID3,
- .temp_aux = WM97XX_AUX_ID2,
- .charge_gpio = -1,
- .max_voltage = PALMT5_BAT_MAX_VOLTAGE,
- .min_voltage = PALMT5_BAT_MIN_VOLTAGE,
- .batt_mult = 1000,
- .batt_div = 414,
- .temp_mult = 1,
- .temp_div = 1,
- .batt_tech = POWER_SUPPLY_TECHNOLOGY_LIPO,
- .batt_name = "main-batt",
-};
-
-static struct wm97xx_pdata palmt5_wm97xx_pdata = {
- .batt_pdata = &palmt5_batt_pdata,
-};
-
-static pxa2xx_audio_ops_t palmt5_ac97_pdata = {
- .reset_gpio = 95,
- .codec_pdata = { &palmt5_wm97xx_pdata, },
-};
-
-static struct palm27x_asoc_info palmt5_asoc_pdata = {
- .jack_gpio = GPIO_NR_PALMT5_EARPHONE_DETECT,
-};
-
-static struct platform_device palmt5_asoc = {
- .name = "palm27x-asoc",
- .id = -1,
- .dev = {
- .platform_data = &palmt5_asoc_pdata,
- },
-};
-
-/******************************************************************************
- * Framebuffer
- ******************************************************************************/
-static struct pxafb_mode_info palmt5_lcd_modes[] = {
-{
- .pixclock = 57692,
- .xres = 320,
- .yres = 480,
- .bpp = 16,
-
- .left_margin = 32,
- .right_margin = 1,
- .upper_margin = 7,
- .lower_margin = 1,
-
- .hsync_len = 4,
- .vsync_len = 1,
-},
-};
-
-static struct pxafb_mach_info palmt5_lcd_screen = {
- .modes = palmt5_lcd_modes,
- .num_modes = ARRAY_SIZE(palmt5_lcd_modes),
- .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
-};
-
-/******************************************************************************
- * Power management - standby
- ******************************************************************************/
-static void __init palmt5_pm_init(void)
+static void __init palmt5_keys_init(void)
{
- static u32 resume[] = {
- 0xe3a00101, /* mov r0, #0x40000000 */
- 0xe380060f, /* orr r0, r0, #0x00f00000 */
- 0xe590f008, /* ldr pc, [r0, #0x08] */
- };
-
- /* copy the bootloader */
- memcpy(phys_to_virt(PALMT5_STR_BASE), resume, sizeof(resume));
+ platform_device_register(&palmt5_pxa_keys);
}
+#else
+static inline void palmt5_keys_init(void) {}
+#endif
/******************************************************************************
* Machine init
******************************************************************************/
-static struct platform_device *devices[] __initdata = {
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
- &palmt5_pxa_keys,
-#endif
- &palmt5_backlight,
- &power_supply,
- &palmt5_asoc,
- &palmt5_gpio_vbus,
-};
-
-/* setup udc GPIOs initial state */
-static void __init palmt5_udc_init(void)
-{
- if (!gpio_request(GPIO_NR_PALMT5_USB_PULLUP, "UDC Vbus")) {
- gpio_direction_output(GPIO_NR_PALMT5_USB_PULLUP, 1);
- gpio_free(GPIO_NR_PALMT5_USB_PULLUP);
- }
-}
-
static void __init palmt5_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(palmt5_pin_config));
-
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
- palmt5_pm_init();
- set_pxa_fb_info(&palmt5_lcd_screen);
- pxa_set_mci_info(&palmt5_mci_platform_data);
- palmt5_udc_init();
- pxa_set_ac97_info(&palmt5_ac97_pdata);
- pxa_set_ficp_info(&palmt5_ficp_platform_data);
- pxa_set_keypad_info(&palmt5_keypad_platform_data);
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
+ palm27x_mmc_init(GPIO_NR_PALMT5_SD_DETECT_N, GPIO_NR_PALMT5_SD_READONLY,
+ GPIO_NR_PALMT5_SD_POWER, 0);
+ palm27x_pm_init(PALMT5_STR_BASE);
+ palm27x_lcd_init(-1, &palm_320x480_lcd_mode);
+ palm27x_udc_init(GPIO_NR_PALMT5_USB_DETECT_N,
+ GPIO_NR_PALMT5_USB_PULLUP, 1);
+ palm27x_irda_init(GPIO_NR_PALMT5_IR_DISABLE);
+ palm27x_ac97_init(PALMT5_BAT_MIN_VOLTAGE, PALMT5_BAT_MAX_VOLTAGE,
+ GPIO_NR_PALMT5_EARPHONE_DETECT, 95);
+ palm27x_pwm_init(GPIO_NR_PALMT5_BL_POWER, GPIO_NR_PALMT5_LCD_POWER);
+ palm27x_power_init(GPIO_NR_PALMT5_POWER_DETECT, -1);
+ palm27x_pmic_init();
+ palmt5_kpc_init();
+ palmt5_keys_init();
}
MACHINE_START(PALMT5, "Palm Tungsten|T5")
diff --git a/arch/arm/mach-pxa/palmtreo.c b/arch/arm/mach-pxa/palmtreo.c
index 4eb0258..08dd89e 100644
--- a/arch/arm/mach-pxa/palmtreo.c
+++ b/arch/arm/mach-pxa/palmtreo.c
@@ -44,6 +44,7 @@
#include <mach/pxa2xx-regs.h>
#include <mach/palmasoc.h>
#include <mach/camera.h>
+#include <mach/palm27x.h>
#include <sound/pxa2xx-lib.h>
@@ -158,31 +159,9 @@ static unsigned long centro685_pin_config[] __initdata = {
#endif /* CONFIG_MACH_CENTRO */
/******************************************************************************
- * SD/MMC card controller
- ******************************************************************************/
-#ifdef CONFIG_MACH_TREO680
-static struct pxamci_platform_data treo680_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_card_detect = GPIO_NR_TREO_SD_DETECT_N,
- .gpio_card_ro = GPIO_NR_TREO680_SD_READONLY,
- .gpio_power = GPIO_NR_TREO680_SD_POWER,
-};
-#endif /* CONFIG_MACH_TREO680 */
-
-#ifdef CONFIG_MACH_CENTRO
-static struct pxamci_platform_data centro_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_card_detect = GPIO_NR_TREO_SD_DETECT_N,
- .gpio_card_ro = -1,
- .gpio_power = GPIO_NR_CENTRO_SD_POWER,
- .gpio_power_invert = 1,
-};
-#endif /* CONFIG_MACH_CENTRO */
-
-/******************************************************************************
* GPIO keyboard
******************************************************************************/
-#ifdef CONFIG_MACH_TREO680
+#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULE)
static unsigned int treo680_matrix_keys[] = {
KEY(0, 0, KEY_F8), /* Red/Off/Power */
KEY(0, 1, KEY_LEFT),
@@ -242,19 +221,6 @@ static unsigned int treo680_matrix_keys[] = {
KEY(7, 5, KEY_I),
};
-static struct pxa27x_keypad_platform_data treo680_keypad_platform_data = {
- .matrix_key_rows = 8,
- .matrix_key_cols = 7,
- .matrix_key_map = treo680_matrix_keys,
- .matrix_key_map_size = ARRAY_SIZE(treo680_matrix_keys),
- .direct_key_map = { KEY_CONNECT },
- .direct_key_num = 1,
-
- .debounce_interval = 30,
-};
-#endif /* CONFIG_MACH_TREO680 */
-
-#ifdef CONFIG_MACH_CENTRO
static unsigned int centro_matrix_keys[] = {
KEY(0, 0, KEY_F9), /* Home */
KEY(0, 1, KEY_LEFT),
@@ -314,157 +280,50 @@ static unsigned int centro_matrix_keys[] = {
KEY(7, 5, KEY_I),
};
-static struct pxa27x_keypad_platform_data centro_keypad_platform_data = {
+static struct pxa27x_keypad_platform_data treo680_keypad_pdata = {
.matrix_key_rows = 8,
.matrix_key_cols = 7,
- .matrix_key_map = centro_matrix_keys,
- .matrix_key_map_size = ARRAY_SIZE(centro_matrix_keys),
+ .matrix_key_map = treo680_matrix_keys,
+ .matrix_key_map_size = ARRAY_SIZE(treo680_matrix_keys),
.direct_key_map = { KEY_CONNECT },
.direct_key_num = 1,
.debounce_interval = 30,
};
-#endif /* CONFIG_MACH_CENTRO */
-/******************************************************************************
- * aSoC audio
- ******************************************************************************/
-
-static pxa2xx_audio_ops_t treo_ac97_pdata = {
- .reset_gpio = 95,
-};
-
-/******************************************************************************
- * Backlight
- ******************************************************************************/
-static int treo_backlight_init(struct device *dev)
+static void __init palmtreo_kpc_init(void)
{
- int ret;
-
- ret = gpio_request(GPIO_NR_TREO_BL_POWER, "BL POWER");
- if (ret)
- goto err;
- ret = gpio_direction_output(GPIO_NR_TREO_BL_POWER, 0);
- if (ret)
- goto err2;
-
- return 0;
+ static struct pxa27x_keypad_platform_data *data = &treo680_keypad_pdata;
-err2:
- gpio_free(GPIO_NR_TREO_BL_POWER);
-err:
- return ret;
-}
-
-static int treo_backlight_notify(struct device *dev, int brightness)
-{
- gpio_set_value(GPIO_NR_TREO_BL_POWER, brightness);
- return TREO_MAX_INTENSITY - brightness;
-};
+ if (machine_is_centro()) {
+ data->matrix_key_map = centro_matrix_keys;
+ data->matrix_key_map_size = ARRAY_SIZE(centro_matrix_keys);
+ }
-static void treo_backlight_exit(struct device *dev)
-{
- gpio_free(GPIO_NR_TREO_BL_POWER);
+ pxa_set_keypad_info(&treo680_keypad_pdata);
}
-
-static struct platform_pwm_backlight_data treo_backlight_data = {
- .pwm_id = 0,
- .max_brightness = TREO_MAX_INTENSITY,
- .dft_brightness = TREO_DEFAULT_INTENSITY,
- .pwm_period_ns = TREO_PERIOD_NS,
- .init = treo_backlight_init,
- .notify = treo_backlight_notify,
- .exit = treo_backlight_exit,
-};
-
-static struct platform_device treo_backlight = {
- .name = "pwm-backlight",
- .dev = {
- .parent = &pxa27x_device_pwm0.dev,
- .platform_data = &treo_backlight_data,
- },
-};
-
-/******************************************************************************
- * IrDA
- ******************************************************************************/
-static struct pxaficp_platform_data treo_ficp_info = {
- .gpio_pwdown = GPIO_NR_TREO_IR_EN,
- .transceiver_cap = IR_SIRMODE | IR_OFF,
-};
-
-/******************************************************************************
- * UDC
- ******************************************************************************/
-static struct pxa2xx_udc_mach_info treo_udc_info __initdata = {
- .gpio_vbus = GPIO_NR_TREO_USB_DETECT,
- .gpio_vbus_inverted = 1,
- .gpio_pullup = GPIO_NR_TREO_USB_PULLUP,
-};
-
+#else
+static inline void palmtreo_kpc_init(void) {}
+#endif
/******************************************************************************
* USB host
******************************************************************************/
-#ifdef CONFIG_MACH_TREO680
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
static struct pxaohci_platform_data treo680_ohci_info = {
.port_mode = PMM_PERPORT_MODE,
.flags = ENABLE_PORT1 | ENABLE_PORT3,
.power_budget = 0,
};
-#endif /* CONFIG_MACH_TREO680 */
-/******************************************************************************
- * Power supply
- ******************************************************************************/
-static int power_supply_init(struct device *dev)
+static void __init palmtreo_uhc_init(void)
{
- int ret;
-
- ret = gpio_request(GPIO_NR_TREO_POWER_DETECT, "CABLE_STATE_AC");
- if (ret)
- goto err1;
- ret = gpio_direction_input(GPIO_NR_TREO_POWER_DETECT);
- if (ret)
- goto err2;
-
- return 0;
-
-err2:
- gpio_free(GPIO_NR_TREO_POWER_DETECT);
-err1:
- return ret;
-}
-
-static int treo_is_ac_online(void)
-{
- return gpio_get_value(GPIO_NR_TREO_POWER_DETECT);
+ if (machine_is_treo680())
+ pxa_set_ohci_info(&treo680_ohci_info);
}
-
-static void power_supply_exit(struct device *dev)
-{
- gpio_free(GPIO_NR_TREO_POWER_DETECT);
-}
-
-static char *treo_supplicants[] = {
- "main-battery",
-};
-
-static struct pda_power_pdata power_supply_info = {
- .init = power_supply_init,
- .is_ac_online = treo_is_ac_online,
- .exit = power_supply_exit,
- .supplied_to = treo_supplicants,
- .num_supplicants = ARRAY_SIZE(treo_supplicants),
-};
-
-static struct platform_device power_supply = {
- .name = "pda-power",
- .id = -1,
- .dev = {
- .platform_data = &power_supply_info,
- },
-};
+#else
+static inline void palmtreo_uhc_init(void) {}
+#endif
/******************************************************************************
* Vibra and LEDs
@@ -493,16 +352,6 @@ static struct gpio_led_platform_data treo680_gpio_led_info = {
.num_leds = ARRAY_SIZE(treo680_gpio_leds),
};
-static struct platform_device treo680_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &treo680_gpio_led_info,
- }
-};
-#endif /* CONFIG_MACH_TREO680 */
-
-#ifdef CONFIG_MACH_CENTRO
static struct gpio_led centro_gpio_leds[] = {
{
.name = "centro:vibra:vibra",
@@ -527,139 +376,61 @@ static struct gpio_led_platform_data centro_gpio_led_info = {
.num_leds = ARRAY_SIZE(centro_gpio_leds),
};
-static struct platform_device centro_leds = {
+static struct platform_device palmtreo_leds = {
.name = "leds-gpio",
.id = -1,
.dev = {
- .platform_data = ¢ro_gpio_led_info,
+ .platform_data = &treo680_gpio_led_info,
}
};
-#endif /* CONFIG_MACH_CENTRO */
-
-/******************************************************************************
- * Framebuffer
- ******************************************************************************/
-/* TODO: add support for 324x324 */
-static struct pxafb_mode_info treo_lcd_modes[] = {
-{
- .pixclock = 86538,
- .xres = 320,
- .yres = 320,
- .bpp = 16,
-
- .left_margin = 20,
- .right_margin = 8,
- .upper_margin = 8,
- .lower_margin = 5,
-
- .hsync_len = 4,
- .vsync_len = 1,
-},
-};
-static void treo_lcd_power(int on, struct fb_var_screeninfo *info)
+static void __init palmtreo_leds_init(void)
{
- gpio_set_value(GPIO_NR_TREO_BL_POWER, on);
-}
-
-static struct pxafb_mach_info treo_lcd_screen = {
- .modes = treo_lcd_modes,
- .num_modes = ARRAY_SIZE(treo_lcd_modes),
- .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
-};
+ if (machine_is_centro())
+ palmtreo_leds.dev.platform_data = ¢ro_gpio_led_info;
-/******************************************************************************
- * Power management - standby
- ******************************************************************************/
-static void __init treo_pm_init(void)
-{
- static u32 resume[] = {
- 0xe3a00101, /* mov r0, #0x40000000 */
- 0xe380060f, /* orr r0, r0, #0x00f00000 */
- 0xe590f008, /* ldr pc, [r0, #0x08] */
- };
-
- /* this is where the bootloader jumps */
- memcpy(phys_to_virt(TREO_STR_BASE), resume, sizeof(resume));
+ platform_device_register(&palmtreo_leds);
}
+#else
+static inline void palmtreo_leds_init(void) {}
+#endif
/******************************************************************************
* Machine init
******************************************************************************/
-static struct platform_device *treo_devices[] __initdata = {
- &treo_backlight,
- &power_supply,
-};
-
-#ifdef CONFIG_MACH_TREO680
-static struct platform_device *treo680_devices[] __initdata = {
- &treo680_leds,
-};
-#endif /* CONFIG_MACH_TREO680 */
-
-#ifdef CONFIG_MACH_CENTRO
-static struct platform_device *centro_devices[] __initdata = {
- ¢ro_leds,
-};
-#endif /* CONFIG_MACH_CENTRO */
-
-/* setup udc GPIOs initial state */
-static void __init treo_udc_init(void)
-{
- if (!gpio_request(GPIO_NR_TREO_USB_PULLUP, "UDC Vbus")) {
- gpio_direction_output(GPIO_NR_TREO_USB_PULLUP, 1);
- gpio_free(GPIO_NR_TREO_USB_PULLUP);
- }
-}
-
-static void __init treo_lcd_power_init(void)
-{
- int ret;
-
- ret = gpio_request(GPIO_NR_TREO_LCD_POWER, "LCD POWER");
- if (ret) {
- pr_err("Treo680: LCD power GPIO request failed!\n");
- return;
- }
-
- ret = gpio_direction_output(GPIO_NR_TREO_LCD_POWER, 0);
- if (ret) {
- pr_err("Treo680: setting LCD power GPIO direction failed!\n");
- gpio_free(GPIO_NR_TREO_LCD_POWER);
- return;
- }
-
- treo_lcd_screen.pxafb_lcd_power = treo_lcd_power;
-}
-
-static void __init treo_init(void)
+static void __init palmphone_common_init(void)
{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(treo_pin_config));
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
-
- treo_pm_init();
- pxa2xx_mfp_config(ARRAY_AND_SIZE(treo_pin_config));
- treo_lcd_power_init();
- set_pxa_fb_info(&treo_lcd_screen);
- treo_udc_init();
- pxa_set_udc_info(&treo_udc_info);
- pxa_set_ac97_info(&treo_ac97_pdata);
- pxa_set_ficp_info(&treo_ficp_info);
-
- platform_add_devices(ARRAY_AND_SIZE(treo_devices));
+ palm27x_pm_init(TREO_STR_BASE);
+ palm27x_lcd_init(GPIO_NR_TREO_BL_POWER, &palm_320x320_new_lcd_mode);
+ palm27x_udc_init(GPIO_NR_TREO_USB_DETECT, GPIO_NR_TREO_USB_PULLUP, 1);
+ palm27x_irda_init(GPIO_NR_TREO_IR_EN);
+ palm27x_ac97_init(-1, -1, -1, 95);
+ palm27x_pwm_init(GPIO_NR_TREO_BL_POWER, -1);
+ palm27x_power_init(GPIO_NR_TREO_POWER_DETECT, -1);
+ palm27x_pmic_init();
+ palmtreo_kpc_init();
+ palmtreo_uhc_init();
+ palmtreo_leds_init();
}
-#ifdef CONFIG_MACH_TREO680
static void __init treo680_init(void)
{
- treo_init();
pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config));
- pxa_set_mci_info(&treo680_mci_platform_data);
- pxa_set_keypad_info(&treo680_keypad_platform_data);
- pxa_set_ohci_info(&treo680_ohci_info);
+ palmphone_common_init();
+ palm27x_mmc_init(GPIO_NR_TREO_SD_DETECT_N, GPIO_NR_TREO680_SD_READONLY,
+ GPIO_NR_TREO680_SD_POWER, 0);
+}
- platform_add_devices(ARRAY_AND_SIZE(treo680_devices));
+static void __init centro_init(void)
+{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(centro685_pin_config));
+ palmphone_common_init();
+ palm27x_mmc_init(GPIO_NR_TREO_SD_DETECT_N, -1,
+ GPIO_NR_CENTRO_SD_POWER, 1);
}
MACHINE_START(TREO680, "Palm Treo 680")
@@ -669,21 +440,8 @@ MACHINE_START(TREO680, "Palm Treo 680")
.map_io = pxa_map_io,
.init_irq = pxa27x_init_irq,
.timer = &pxa_timer,
- .init_machine = treo680_init,
+ .init_machine = palmtreo_init,
MACHINE_END
-#endif /* CONFIG_MACH_TREO680 */
-
-#ifdef CONFIG_MACH_CENTRO
-static void __init centro_init(void)
-{
- treo_init();
- pxa2xx_mfp_config(ARRAY_AND_SIZE(centro685_pin_config));
- pxa_set_mci_info(¢ro_mci_platform_data);
-
- pxa_set_keypad_info(¢ro_keypad_platform_data);
-
- platform_add_devices(ARRAY_AND_SIZE(centro_devices));
-}
MACHINE_START(CENTRO, "Palm Centro 685")
.phys_io = TREO_PHYS_IO_START,
@@ -692,6 +450,5 @@ MACHINE_START(CENTRO, "Palm Centro 685")
.map_io = pxa_map_io,
.init_irq = pxa27x_init_irq,
.timer = &pxa_timer,
- .init_machine = centro_init,
+ .init_machine = palmtreo_init,
MACHINE_END
-#endif /* CONFIG_MACH_CENTRO */
diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c
index a5429cd..144dc2b 100644
--- a/arch/arm/mach-pxa/palmtx.c
+++ b/arch/arm/mach-pxa/palmtx.c
@@ -46,6 +46,7 @@
#include <mach/pxa27x_keypad.h>
#include <mach/udc.h>
#include <mach/palmasoc.h>
+#include <mach/palm27x.h>
#include "generic.h"
#include "devices.h"
@@ -129,6 +130,7 @@ static unsigned long palmtx_pin_config[] __initdata = {
/******************************************************************************
* NOR Flash
******************************************************************************/
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
static struct mtd_partition palmtx_partitions[] = {
{
.name = "Flash",
@@ -162,20 +164,18 @@ static struct platform_device palmtx_flash = {
},
};
-/******************************************************************************
- * SD/MMC card controller
- ******************************************************************************/
-static struct pxamci_platform_data palmtx_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_card_detect = GPIO_NR_PALMTX_SD_DETECT_N,
- .gpio_card_ro = GPIO_NR_PALMTX_SD_READONLY,
- .gpio_power = GPIO_NR_PALMTX_SD_POWER,
- .detect_delay_ms = 200,
-};
+static void __init palmtx_nor_init(void)
+{
+ platform_device_register(&palmtx_flash);
+}
+#else
+static inline void palmtx_nor_init(void) {}
+#endif
/******************************************************************************
* GPIO keyboard
******************************************************************************/
+#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULE)
static unsigned int palmtx_matrix_keys[] = {
KEY(0, 0, KEY_POWER),
KEY(0, 1, KEY_F1),
@@ -201,9 +201,18 @@ static struct pxa27x_keypad_platform_data palmtx_keypad_platform_data = {
.debounce_interval = 30,
};
+static void __init palmtx_kpc_init(void)
+{
+ pxa_set_keypad_info(&palmtx_keypad_platform_data);
+}
+#else
+static inline void palmtx_kpc_init(void) {}
+#endif
+
/******************************************************************************
* GPIO keys
******************************************************************************/
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
static struct gpio_keys_button palmtx_pxa_buttons[] = {
{KEY_F8, GPIO_NR_PALMTX_HOTSYNC_BUTTON_N, 1, "HotSync Button" },
};
@@ -221,210 +230,18 @@ static struct platform_device palmtx_pxa_keys = {
},
};
-/******************************************************************************
- * Backlight
- ******************************************************************************/
-static int palmtx_backlight_init(struct device *dev)
-{
- int ret;
-
- ret = gpio_request(GPIO_NR_PALMTX_BL_POWER, "BL POWER");
- if (ret)
- goto err;
- ret = gpio_direction_output(GPIO_NR_PALMTX_BL_POWER, 0);
- if (ret)
- goto err2;
- ret = gpio_request(GPIO_NR_PALMTX_LCD_POWER, "LCD POWER");
- if (ret)
- goto err2;
- ret = gpio_direction_output(GPIO_NR_PALMTX_LCD_POWER, 0);
- if (ret)
- goto err3;
-
- return 0;
-err3:
- gpio_free(GPIO_NR_PALMTX_LCD_POWER);
-err2:
- gpio_free(GPIO_NR_PALMTX_BL_POWER);
-err:
- return ret;
-}
-
-static int palmtx_backlight_notify(struct device *dev, int brightness)
-{
- gpio_set_value(GPIO_NR_PALMTX_BL_POWER, brightness);
- gpio_set_value(GPIO_NR_PALMTX_LCD_POWER, brightness);
- return brightness;
-}
-
-static void palmtx_backlight_exit(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMTX_BL_POWER);
- gpio_free(GPIO_NR_PALMTX_LCD_POWER);
-}
-
-static struct platform_pwm_backlight_data palmtx_backlight_data = {
- .pwm_id = 0,
- .max_brightness = PALMTX_MAX_INTENSITY,
- .dft_brightness = PALMTX_MAX_INTENSITY,
- .pwm_period_ns = PALMTX_PERIOD_NS,
- .init = palmtx_backlight_init,
- .notify = palmtx_backlight_notify,
- .exit = palmtx_backlight_exit,
-};
-
-static struct platform_device palmtx_backlight = {
- .name = "pwm-backlight",
- .dev = {
- .parent = &pxa27x_device_pwm0.dev,
- .platform_data = &palmtx_backlight_data,
- },
-};
-
-/******************************************************************************
- * IrDA
- ******************************************************************************/
-static struct pxaficp_platform_data palmtx_ficp_platform_data = {
- .gpio_pwdown = GPIO_NR_PALMTX_IR_DISABLE,
- .transceiver_cap = IR_SIRMODE | IR_OFF,
-};
-
-/******************************************************************************
- * UDC
- ******************************************************************************/
-static struct gpio_vbus_mach_info palmtx_udc_info = {
- .gpio_vbus = GPIO_NR_PALMTX_USB_DETECT_N,
- .gpio_vbus_inverted = 1,
- .gpio_pullup = GPIO_NR_PALMTX_USB_PULLUP,
-};
-
-static struct platform_device palmtx_gpio_vbus = {
- .name = "gpio-vbus",
- .id = -1,
- .dev = {
- .platform_data = &palmtx_udc_info,
- },
-};
-
-/******************************************************************************
- * Power supply
- ******************************************************************************/
-static int power_supply_init(struct device *dev)
-{
- int ret;
-
- ret = gpio_request(GPIO_NR_PALMTX_POWER_DETECT, "CABLE_STATE_AC");
- if (ret)
- goto err1;
- ret = gpio_direction_input(GPIO_NR_PALMTX_POWER_DETECT);
- if (ret)
- goto err2;
-
- return 0;
-
-err2:
- gpio_free(GPIO_NR_PALMTX_POWER_DETECT);
-err1:
- return ret;
-}
-
-static int palmtx_is_ac_online(void)
-{
- return gpio_get_value(GPIO_NR_PALMTX_POWER_DETECT);
-}
-
-static void power_supply_exit(struct device *dev)
+static void __init palmtx_keys_init(void)
{
- gpio_free(GPIO_NR_PALMTX_POWER_DETECT);
+ platform_device_register(&palmtx_pxa_keys);
}
-
-static char *palmtx_supplicants[] = {
- "main-battery",
-};
-
-static struct pda_power_pdata power_supply_info = {
- .init = power_supply_init,
- .is_ac_online = palmtx_is_ac_online,
- .exit = power_supply_exit,
- .supplied_to = palmtx_supplicants,
- .num_supplicants = ARRAY_SIZE(palmtx_supplicants),
-};
-
-static struct platform_device power_supply = {
- .name = "pda-power",
- .id = -1,
- .dev = {
- .platform_data = &power_supply_info,
- },
-};
-
-/******************************************************************************
- * WM97xx audio, battery
- ******************************************************************************/
-static struct wm97xx_batt_pdata palmtx_batt_pdata = {
- .batt_aux = WM97XX_AUX_ID3,
- .temp_aux = WM97XX_AUX_ID2,
- .charge_gpio = -1,
- .max_voltage = PALMTX_BAT_MAX_VOLTAGE,
- .min_voltage = PALMTX_BAT_MIN_VOLTAGE,
- .batt_mult = 1000,
- .batt_div = 414,
- .temp_mult = 1,
- .temp_div = 1,
- .batt_tech = POWER_SUPPLY_TECHNOLOGY_LIPO,
- .batt_name = "main-batt",
-};
-
-static struct wm97xx_pdata palmtx_wm97xx_pdata = {
- .batt_pdata = &palmtx_batt_pdata,
-};
-
-static pxa2xx_audio_ops_t palmtx_ac97_pdata = {
- .reset_gpio = 95,
- .codec_pdata = { &palmtx_wm97xx_pdata, },
-};
-
-static struct palm27x_asoc_info palmtx_asoc_pdata = {
- .jack_gpio = GPIO_NR_PALMTX_EARPHONE_DETECT,
-};
-
-static struct platform_device palmtx_asoc = {
- .name = "palm27x-asoc",
- .id = -1,
- .dev = {
- .platform_data = &palmtx_asoc_pdata,
- },
-};
-
-/******************************************************************************
- * Framebuffer
- ******************************************************************************/
-static struct pxafb_mode_info palmtx_lcd_modes[] = {
-{
- .pixclock = 57692,
- .xres = 320,
- .yres = 480,
- .bpp = 16,
-
- .left_margin = 32,
- .right_margin = 1,
- .upper_margin = 7,
- .lower_margin = 1,
-
- .hsync_len = 4,
- .vsync_len = 1,
-},
-};
-
-static struct pxafb_mach_info palmtx_lcd_screen = {
- .modes = palmtx_lcd_modes,
- .num_modes = ARRAY_SIZE(palmtx_lcd_modes),
- .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
-};
+#else
+static inline void palmtx_keys_init(void) {}
+#endif
/******************************************************************************
* NAND Flash
******************************************************************************/
+#if defined(CONFIG_MTD_NAND_GPIO) || defined(CONFIG_MTD_NAND_GPIO_MODULE)
static void palmtx_nand_cmd_ctl(struct mtd_info *mtd, int cmd,
unsigned int ctrl)
{
@@ -484,36 +301,17 @@ static struct platform_device palmtx_nand = {
}
};
-/******************************************************************************
- * Power management - standby
- ******************************************************************************/
-static void __init palmtx_pm_init(void)
+static void __init palmtx_nand_init(void)
{
- static u32 resume[] = {
- 0xe3a00101, /* mov r0, #0x40000000 */
- 0xe380060f, /* orr r0, r0, #0x00f00000 */
- 0xe590f008, /* ldr pc, [r0, #0x08] */
- };
-
- /* copy the bootloader */
- memcpy(phys_to_virt(PALMTX_STR_BASE), resume, sizeof(resume));
+ platform_device_register(&palmtx_nand);
}
+#else
+static inline void palmtx_nand_init(void) {}
+#endif
/******************************************************************************
* Machine init
******************************************************************************/
-static struct platform_device *devices[] __initdata = {
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
- &palmtx_pxa_keys,
-#endif
- &palmtx_backlight,
- &power_supply,
- &palmtx_asoc,
- &palmtx_gpio_vbus,
- &palmtx_flash,
- &palmtx_nand,
-};
-
static struct map_desc palmtx_io_desc[] __initdata = {
{
.virtual = PALMTX_PCMCIA_VIRT,
@@ -539,33 +337,29 @@ static void __init palmtx_map_io(void)
iotable_init(palmtx_io_desc, ARRAY_SIZE(palmtx_io_desc));
}
-/* setup udc GPIOs initial state */
-static void __init palmtx_udc_init(void)
-{
- if (!gpio_request(GPIO_NR_PALMTX_USB_PULLUP, "UDC Vbus")) {
- gpio_direction_output(GPIO_NR_PALMTX_USB_PULLUP, 1);
- gpio_free(GPIO_NR_PALMTX_USB_PULLUP);
- }
-}
-
-
static void __init palmtx_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(palmtx_pin_config));
-
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
- palmtx_pm_init();
- set_pxa_fb_info(&palmtx_lcd_screen);
- pxa_set_mci_info(&palmtx_mci_platform_data);
- palmtx_udc_init();
- pxa_set_ac97_info(&palmtx_ac97_pdata);
- pxa_set_ficp_info(&palmtx_ficp_platform_data);
- pxa_set_keypad_info(&palmtx_keypad_platform_data);
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
+ palm27x_mmc_init(GPIO_NR_PALMTX_SD_DETECT_N, GPIO_NR_PALMTX_SD_READONLY,
+ GPIO_NR_PALMTX_SD_POWER, 0);
+ palm27x_pm_init(PALMTX_STR_BASE);
+ palm27x_lcd_init(-1, &palm_320x480_lcd_mode);
+ palm27x_udc_init(GPIO_NR_PALMTX_USB_DETECT_N,
+ GPIO_NR_PALMTX_USB_PULLUP, 1);
+ palm27x_irda_init(GPIO_NR_PALMTX_IR_DISABLE);
+ palm27x_ac97_init(PALMTX_BAT_MIN_VOLTAGE, PALMTX_BAT_MAX_VOLTAGE,
+ GPIO_NR_PALMTX_EARPHONE_DETECT, 95);
+ palm27x_pwm_init(GPIO_NR_PALMTX_BL_POWER, GPIO_NR_PALMTX_LCD_POWER);
+ palm27x_power_init(GPIO_NR_PALMTX_POWER_DETECT, -1);
+ palm27x_pmic_init();
+ palmtx_kpc_init();
+ palmtx_keys_init();
+ palmtx_nor_init();
+ palmtx_nand_init();
}
MACHINE_START(PALMTX, "Palm T|X")
diff --git a/arch/arm/mach-pxa/palmz72.c b/arch/arm/mach-pxa/palmz72.c
index b78c6b4..87e4b10 100644
--- a/arch/arm/mach-pxa/palmz72.c
+++ b/arch/arm/mach-pxa/palmz72.c
@@ -44,6 +44,7 @@
#include <mach/pxa27x_keypad.h>
#include <mach/udc.h>
#include <mach/palmasoc.h>
+#include <mach/palm27x.h>
#include <mach/pm.h>
@@ -109,21 +110,9 @@ static unsigned long palmz72_pin_config[] __initdata = {
};
/******************************************************************************
- * SD/MMC card controller
- ******************************************************************************/
-/* SD_POWER is not actually power, but it is more like chip
- * select, i.e. it is inverted */
-static struct pxamci_platform_data palmz72_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .gpio_card_detect = GPIO_NR_PALMZ72_SD_DETECT_N,
- .gpio_card_ro = GPIO_NR_PALMZ72_SD_RO,
- .gpio_power = GPIO_NR_PALMZ72_SD_POWER_N,
- .gpio_power_invert = 1,
-};
-
-/******************************************************************************
* GPIO keyboard
******************************************************************************/
+#if defined(CONFIG_KEYBOARD_PXA27x) || defined(CONFIG_KEYBOARD_PXA27x_MODULE)
static unsigned int palmz72_matrix_keys[] = {
KEY(0, 0, KEY_POWER),
KEY(0, 1, KEY_F1),
@@ -149,77 +138,18 @@ static struct pxa27x_keypad_platform_data palmz72_keypad_platform_data = {
.debounce_interval = 30,
};
-/******************************************************************************
- * Backlight
- ******************************************************************************/
-static int palmz72_backlight_init(struct device *dev)
+static void __init palmz72_kpc_init(void)
{
- int ret;
-
- ret = gpio_request(GPIO_NR_PALMZ72_BL_POWER, "BL POWER");
- if (ret)
- goto err;
- ret = gpio_direction_output(GPIO_NR_PALMZ72_BL_POWER, 0);
- if (ret)
- goto err2;
- ret = gpio_request(GPIO_NR_PALMZ72_LCD_POWER, "LCD POWER");
- if (ret)
- goto err2;
- ret = gpio_direction_output(GPIO_NR_PALMZ72_LCD_POWER, 0);
- if (ret)
- goto err3;
-
- return 0;
-err3:
- gpio_free(GPIO_NR_PALMZ72_LCD_POWER);
-err2:
- gpio_free(GPIO_NR_PALMZ72_BL_POWER);
-err:
- return ret;
-}
-
-static int palmz72_backlight_notify(struct device *dev, int brightness)
-{
- gpio_set_value(GPIO_NR_PALMZ72_BL_POWER, brightness);
- gpio_set_value(GPIO_NR_PALMZ72_LCD_POWER, brightness);
- return brightness;
-}
-
-static void palmz72_backlight_exit(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMZ72_BL_POWER);
- gpio_free(GPIO_NR_PALMZ72_LCD_POWER);
+ pxa_set_keypad_info(&palmz72_keypad_platform_data);
}
-
-static struct platform_pwm_backlight_data palmz72_backlight_data = {
- .pwm_id = 0,
- .max_brightness = PALMZ72_MAX_INTENSITY,
- .dft_brightness = PALMZ72_MAX_INTENSITY,
- .pwm_period_ns = PALMZ72_PERIOD_NS,
- .init = palmz72_backlight_init,
- .notify = palmz72_backlight_notify,
- .exit = palmz72_backlight_exit,
-};
-
-static struct platform_device palmz72_backlight = {
- .name = "pwm-backlight",
- .dev = {
- .parent = &pxa27x_device_pwm0.dev,
- .platform_data = &palmz72_backlight_data,
- },
-};
-
-/******************************************************************************
- * IrDA
- ******************************************************************************/
-static struct pxaficp_platform_data palmz72_ficp_platform_data = {
- .gpio_pwdown = GPIO_NR_PALMZ72_IR_DISABLE,
- .transceiver_cap = IR_SIRMODE | IR_OFF,
-};
+#else
+static inline void palmz72_kpc_init(void) {}
+#endif
/******************************************************************************
* LEDs
******************************************************************************/
+#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
static struct gpio_led gpio_leds[] = {
{
.name = "palmz72:green:led",
@@ -241,144 +171,13 @@ static struct platform_device palmz72_leds = {
}
};
-/******************************************************************************
- * UDC
- ******************************************************************************/
-static struct gpio_vbus_mach_info palmz72_udc_info = {
- .gpio_vbus = GPIO_NR_PALMZ72_USB_DETECT_N,
- .gpio_pullup = GPIO_NR_PALMZ72_USB_PULLUP,
-};
-
-static struct platform_device palmz72_gpio_vbus = {
- .name = "gpio-vbus",
- .id = -1,
- .dev = {
- .platform_data = &palmz72_udc_info,
- },
-};
-
-/******************************************************************************
- * Power supply
- ******************************************************************************/
-static int power_supply_init(struct device *dev)
-{
- int ret;
-
- ret = gpio_request(GPIO_NR_PALMZ72_POWER_DETECT, "CABLE_STATE_AC");
- if (ret)
- goto err1;
- ret = gpio_direction_input(GPIO_NR_PALMZ72_POWER_DETECT);
- if (ret)
- goto err2;
-
- ret = gpio_request(GPIO_NR_PALMZ72_USB_DETECT_N, "CABLE_STATE_USB");
- if (ret)
- goto err2;
- ret = gpio_direction_input(GPIO_NR_PALMZ72_USB_DETECT_N);
- if (ret)
- goto err3;
-
- return 0;
-err3:
- gpio_free(GPIO_NR_PALMZ72_USB_DETECT_N);
-err2:
- gpio_free(GPIO_NR_PALMZ72_POWER_DETECT);
-err1:
- return ret;
-}
-
-static int palmz72_is_ac_online(void)
-{
- return gpio_get_value(GPIO_NR_PALMZ72_POWER_DETECT);
-}
-
-static int palmz72_is_usb_online(void)
+static void __init palmz72_leds_init(void)
{
- return !gpio_get_value(GPIO_NR_PALMZ72_USB_DETECT_N);
+ platform_device_register(&palmz72_leds);
}
-
-static void power_supply_exit(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMZ72_USB_DETECT_N);
- gpio_free(GPIO_NR_PALMZ72_POWER_DETECT);
-}
-
-static char *palmz72_supplicants[] = {
- "main-battery",
-};
-
-static struct pda_power_pdata power_supply_info = {
- .init = power_supply_init,
- .is_ac_online = palmz72_is_ac_online,
- .is_usb_online = palmz72_is_usb_online,
- .exit = power_supply_exit,
- .supplied_to = palmz72_supplicants,
- .num_supplicants = ARRAY_SIZE(palmz72_supplicants),
-};
-
-static struct platform_device power_supply = {
- .name = "pda-power",
- .id = -1,
- .dev = {
- .platform_data = &power_supply_info,
- },
-};
-
-/******************************************************************************
- * WM97xx audio, battery
- ******************************************************************************/
-static struct wm97xx_batt_pdata palmz72_batt_pdata = {
- .batt_aux = WM97XX_AUX_ID3,
- .temp_aux = WM97XX_AUX_ID2,
- .charge_gpio = -1,
- .max_voltage = PALMZ72_BAT_MAX_VOLTAGE,
- .min_voltage = PALMZ72_BAT_MIN_VOLTAGE,
- .batt_mult = 1000,
- .batt_div = 414,
- .temp_mult = 1,
- .temp_div = 1,
- .batt_tech = POWER_SUPPLY_TECHNOLOGY_LIPO,
- .batt_name = "main-batt",
-};
-
-static struct wm97xx_pdata palmz72_wm97xx_pdata = {
- .batt_pdata = &palmz72_batt_pdata,
-};
-
-static pxa2xx_audio_ops_t palmz72_ac97_pdata = {
- .codec_pdata = { &palmz72_wm97xx_pdata, },
-};
-
-static struct platform_device palmz72_asoc = {
- .name = "palm27x-asoc",
- .id = -1,
-};
-
-/******************************************************************************
- * Framebuffer
- ******************************************************************************/
-static struct pxafb_mode_info palmz72_lcd_modes[] = {
-{
- .pixclock = 115384,
- .xres = 320,
- .yres = 320,
- .bpp = 16,
-
- .left_margin = 27,
- .right_margin = 7,
- .upper_margin = 7,
- .lower_margin = 8,
-
- .hsync_len = 6,
- .vsync_len = 1,
-},
-};
-
-static struct pxafb_mach_info palmz72_lcd_screen = {
- .modes = palmz72_lcd_modes,
- .num_modes = ARRAY_SIZE(palmz72_lcd_modes),
- .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
-};
+#else
+static inline void palmz72_leds_init(void) {}
+#endif
#ifdef CONFIG_PM
@@ -457,39 +256,26 @@ device_initcall(palmz72_pm_init);
/******************************************************************************
* Machine init
******************************************************************************/
-static struct platform_device *devices[] __initdata = {
- &palmz72_backlight,
- &palmz72_leds,
- &palmz72_asoc,
- &power_supply,
- &palmz72_gpio_vbus,
-};
-
-/* setup udc GPIOs initial state */
-static void __init palmz72_udc_init(void)
-{
- if (!gpio_request(GPIO_NR_PALMZ72_USB_PULLUP, "USB Pullup")) {
- gpio_direction_output(GPIO_NR_PALMZ72_USB_PULLUP, 0);
- gpio_free(GPIO_NR_PALMZ72_USB_PULLUP);
- }
-}
-
static void __init palmz72_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(palmz72_pin_config));
-
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
- set_pxa_fb_info(&palmz72_lcd_screen);
- pxa_set_mci_info(&palmz72_mci_platform_data);
- palmz72_udc_init();
- pxa_set_ac97_info(&palmz72_ac97_pdata);
- pxa_set_ficp_info(&palmz72_ficp_platform_data);
- pxa_set_keypad_info(&palmz72_keypad_platform_data);
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
+ palm27x_mmc_init(GPIO_NR_PALMZ72_SD_DETECT_N, GPIO_NR_PALMZ72_SD_RO,
+ GPIO_NR_PALMZ72_SD_POWER_N, 1);
+ palm27x_lcd_init(-1, &palm_320x320_lcd_mode);
+ palm27x_udc_init(GPIO_NR_PALMZ72_USB_DETECT_N,
+ GPIO_NR_PALMZ72_USB_PULLUP, 0);
+ palm27x_irda_init(GPIO_NR_PALMZ72_IR_DISABLE);
+ palm27x_ac97_init(PALMZ72_BAT_MIN_VOLTAGE, PALMZ72_BAT_MAX_VOLTAGE,
+ -1, 113);
+ palm27x_pwm_init(-1, -1);
+ palm27x_power_init(-1, -1);
+ palm27x_pmic_init();
+ palmz72_kpc_init();
+ palmz72_leds_init();
}
MACHINE_START(PALMZ72, "Palm Zire72")
--
1.7.1
More information about the linux-arm-kernel
mailing list