[PATCH] USB-serial dummy cable driver
Marek Vasut
marek.vasut at gmail.com
Mon Aug 2 02:00:07 EDT 2010
This driver is used to implement USB-serial like behaviour over dummy
USB cables. These are used in the following devices:
Funsoft Serial USB driver
Genesys Logic GL620USB USB Laplink cable
HP4x (48/49) Serial cable
Motorola phones
Siemens USB-MPI Serial USB driver
ViVOpay USB Serial Driver
ZIO Motherboard USB driver
Signed-off-by: Marek Vasut <marek.vasut at gmail.com>
---
drivers/usb/serial/Kconfig | 59 ++++++---------------
drivers/usb/serial/Makefile | 7 +--
drivers/usb/serial/funsoft.c | 69 ------------------------
drivers/usb/serial/hp4x.c | 86 ------------------------------
drivers/usb/serial/moto_modem.c | 71 -------------------------
drivers/usb/serial/siemens_mpi.c | 77 ---------------------------
drivers/usb/serial/usb-serial-dummy.c | 92 +++++++++++++++++++++++++++++++++
drivers/usb/serial/vivopay-serial.c | 76 ---------------------------
drivers/usb/serial/zio.c | 64 -----------------------
9 files changed, 111 insertions(+), 490 deletions(-)
delete mode 100644 drivers/usb/serial/funsoft.c
delete mode 100644 drivers/usb/serial/hp4x.c
delete mode 100644 drivers/usb/serial/moto_modem.c
delete mode 100644 drivers/usb/serial/siemens_mpi.c
create mode 100644 drivers/usb/serial/usb-serial-dummy.c
delete mode 100644 drivers/usb/serial/vivopay-serial.c
delete mode 100644 drivers/usb/serial/zio.c
diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
index bd8aab0..9466c4e 100644
--- a/drivers/usb/serial/Kconfig
+++ b/drivers/usb/serial/Kconfig
@@ -116,6 +116,24 @@ config USB_SERIAL_DIGI_ACCELEPORT
To compile this driver as a module, choose M here: the
module will be called digi_acceleport.
+config USB_SERIAL_DUMMY
+ tristate "USB-serial dummy cable driver"
+ help
+ Say Y here if you want to use the USB-serial dummy cable driver.
+
+ This driver is used to implement USB-serial like behaviour over dummy
+ USB cables. These are used in the following devices:
+ Genesys Logic GL620USB USB Laplink cable
+ HP4x (48/49) Serial cable
+ Motorola phones
+ Funsoft Serial USB driver
+ ViVOpay USB Serial Driver
+ ZIO Motherboard USB driver
+ Siemens USB-MPI Serial USB driver
+
+ To compile this driver as a module, choose M here: the
+ module will be called usb-serial-dummy.
+
config USB_SERIAL_CP210X
tristate "USB CP210x family of UART Bridge Controllers"
help
@@ -449,15 +467,6 @@ config USB_SERIAL_MOS7840
To compile this driver as a module, choose M here: the
module will be called mos7840. If unsure, choose N.
-config USB_SERIAL_MOTOROLA
- tristate "USB Motorola Phone modem driver"
- ---help---
- Say Y here if you want to use a Motorola phone with a USB
- connector as a modem link.
-
- To compile this driver as a module, choose M here: the
- module will be called moto_modem. If unsure, choose N.
-
config USB_SERIAL_NAVMAN
tristate "USB Navman GPS device"
help
@@ -512,14 +521,6 @@ config USB_SERIAL_SPCP8X5
To compile this driver as a module, choose M here: the
module will be called spcp8x5.
-config USB_SERIAL_HP4X
- tristate "USB HP4x Calculators support"
- help
- Say Y here if you want to use an Hewlett-Packard 4x Calculator.
-
- To compile this driver as a module, choose M here: the
- module will be called hp4x.
-
config USB_SERIAL_SAFE
tristate "USB Safe Serial (Encapsulated) Driver"
@@ -527,14 +528,6 @@ config USB_SERIAL_SAFE_PADDED
bool "USB Secure Encapsulated Driver - Padded"
depends on USB_SERIAL_SAFE
-config USB_SERIAL_SIEMENS_MPI
- tristate "USB Siemens MPI driver"
- help
- Say M here if you want to use a Siemens USB/MPI adapter.
-
- To compile this driver as a module, choose M here: the
- module will be called siemens_mpi.
-
config USB_SERIAL_SIERRAWIRELESS
tristate "USB Sierra Wireless Driver"
help
@@ -626,22 +619,6 @@ config USB_SERIAL_OPTICON
To compile this driver as a module, choose M here: the
module will be called opticon.
-config USB_SERIAL_VIVOPAY_SERIAL
- tristate "USB ViVOpay serial interface driver"
- help
- Say Y here if you want to use a ViVOtech ViVOpay USB device.
-
- To compile this driver as a module, choose M here: the
- module will be called vivopay-serial.
-
-config USB_SERIAL_ZIO
- tristate "ZIO Motherboard USB serial interface driver"
- help
- Say Y here if you want to use ZIO Motherboard.
-
- To compile this driver as a module, choose M here: the
- module will be called zio.
-
config USB_SERIAL_DEBUG
tristate "USB Debugging Device"
help
diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile
index e54c728..c96e81e 100644
--- a/drivers/usb/serial/Makefile
+++ b/drivers/usb/serial/Makefile
@@ -20,13 +20,12 @@ obj-$(CONFIG_USB_SERIAL_CYBERJACK) += cyberjack.o
obj-$(CONFIG_USB_SERIAL_CYPRESS_M8) += cypress_m8.o
obj-$(CONFIG_USB_SERIAL_DEBUG) += usb_debug.o
obj-$(CONFIG_USB_SERIAL_DIGI_ACCELEPORT) += digi_acceleport.o
+obj-$(CONFIG_USB_SERIAL_DUMMY) += usb-serial-dummy.o
obj-$(CONFIG_USB_SERIAL_EDGEPORT) += io_edgeport.o
obj-$(CONFIG_USB_SERIAL_EDGEPORT_TI) += io_ti.o
obj-$(CONFIG_USB_SERIAL_EMPEG) += empeg.o
obj-$(CONFIG_USB_SERIAL_FTDI_SIO) += ftdi_sio.o
-obj-$(CONFIG_USB_SERIAL_FUNSOFT) += funsoft.o
obj-$(CONFIG_USB_SERIAL_GARMIN) += garmin_gps.o
-obj-$(CONFIG_USB_SERIAL_HP4X) += hp4x.o
obj-$(CONFIG_USB_SERIAL_IPAQ) += ipaq.o
obj-$(CONFIG_USB_SERIAL_IPW) += ipw.o
obj-$(CONFIG_USB_SERIAL_IR) += ir-usb.o
@@ -38,7 +37,6 @@ obj-$(CONFIG_USB_SERIAL_KOBIL_SCT) += kobil_sct.o
obj-$(CONFIG_USB_SERIAL_MCT_U232) += mct_u232.o
obj-$(CONFIG_USB_SERIAL_MOS7720) += mos7720.o
obj-$(CONFIG_USB_SERIAL_MOS7840) += mos7840.o
-obj-$(CONFIG_USB_SERIAL_MOTOROLA) += moto_modem.o
obj-$(CONFIG_USB_SERIAL_NAVMAN) += navman.o
obj-$(CONFIG_USB_SERIAL_OMNINET) += omninet.o
obj-$(CONFIG_USB_SERIAL_OPTICON) += opticon.o
@@ -48,7 +46,6 @@ obj-$(CONFIG_USB_SERIAL_PL2303) += pl2303.o
obj-$(CONFIG_USB_SERIAL_QCAUX) += qcaux.o
obj-$(CONFIG_USB_SERIAL_QUALCOMM) += qcserial.o
obj-$(CONFIG_USB_SERIAL_SAFE) += safe_serial.o
-obj-$(CONFIG_USB_SERIAL_SIEMENS_MPI) += siemens_mpi.o
obj-$(CONFIG_USB_SERIAL_SIERRAWIRELESS) += sierra.o
obj-$(CONFIG_USB_SERIAL_SPCP8X5) += spcp8x5.o
obj-$(CONFIG_USB_SERIAL_SYMBOL) += symbolserial.o
@@ -57,6 +54,4 @@ obj-$(CONFIG_USB_SERIAL_TI) += ti_usb_3410_5052.o
obj-$(CONFIG_USB_SERIAL_VISOR) += visor.o
obj-$(CONFIG_USB_SERIAL_WHITEHEAT) += whiteheat.o
obj-$(CONFIG_USB_SERIAL_XIRCOM) += keyspan_pda.o
-obj-$(CONFIG_USB_SERIAL_VIVOPAY_SERIAL) += vivopay-serial.o
-obj-$(CONFIG_USB_SERIAL_ZIO) += zio.o
diff --git a/drivers/usb/serial/funsoft.c b/drivers/usb/serial/funsoft.c
deleted file mode 100644
index e21ce9d..0000000
--- a/drivers/usb/serial/funsoft.c
+++ /dev/null
@@ -1,69 +0,0 @@
-/*
- * Funsoft Serial USB driver
- *
- * Copyright (C) 2006 Greg Kroah-Hartman <gregkh at suse.de>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License version
- * 2 as published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/tty.h>
-#include <linux/module.h>
-#include <linux/usb.h>
-#include <linux/usb/serial.h>
-#include <linux/uaccess.h>
-
-static int debug;
-
-static const struct usb_device_id id_table[] = {
- { USB_DEVICE(0x1404, 0xcddc) },
- { },
-};
-MODULE_DEVICE_TABLE(usb, id_table);
-
-static struct usb_driver funsoft_driver = {
- .name = "funsoft",
- .probe = usb_serial_probe,
- .disconnect = usb_serial_disconnect,
- .id_table = id_table,
- .no_dynamic_id = 1,
-};
-
-static struct usb_serial_driver funsoft_device = {
- .driver = {
- .owner = THIS_MODULE,
- .name = "funsoft",
- },
- .id_table = id_table,
- .usb_driver = &funsoft_driver,
- .num_ports = 1,
-};
-
-static int __init funsoft_init(void)
-{
- int retval;
-
- retval = usb_serial_register(&funsoft_device);
- if (retval)
- return retval;
- retval = usb_register(&funsoft_driver);
- if (retval)
- usb_serial_deregister(&funsoft_device);
- return retval;
-}
-
-static void __exit funsoft_exit(void)
-{
- usb_deregister(&funsoft_driver);
- usb_serial_deregister(&funsoft_device);
-}
-
-module_init(funsoft_init);
-module_exit(funsoft_exit);
-MODULE_LICENSE("GPL");
-
-module_param(debug, bool, S_IRUGO | S_IWUSR);
-MODULE_PARM_DESC(debug, "Debug enabled or not");
diff --git a/drivers/usb/serial/hp4x.c b/drivers/usb/serial/hp4x.c
deleted file mode 100644
index 8093791..0000000
--- a/drivers/usb/serial/hp4x.c
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * HP4x Calculators Serial USB driver
- *
- * Copyright (C) 2005 Arthur Huillet (ahuillet at users.sf.net)
- * Copyright (C) 2001-2005 Greg Kroah-Hartman (greg at kroah.com)
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * See Documentation/usb/usb-serial.txt for more information on using this
- * driver
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/tty.h>
-#include <linux/module.h>
-#include <linux/usb.h>
-#include <linux/usb/serial.h>
-
-/*
- * Version Information
- */
-#define DRIVER_VERSION "v1.00"
-#define DRIVER_DESC "HP4x (48/49) Generic Serial driver"
-
-#define HP_VENDOR_ID 0x03f0
-#define HP49GP_PRODUCT_ID 0x0121
-
-static const struct usb_device_id id_table[] = {
- { USB_DEVICE(HP_VENDOR_ID, HP49GP_PRODUCT_ID) },
- { } /* Terminating entry */
-};
-
-MODULE_DEVICE_TABLE(usb, id_table);
-
-static struct usb_driver hp49gp_driver = {
- .name = "hp4X",
- .probe = usb_serial_probe,
- .disconnect = usb_serial_disconnect,
- .id_table = id_table,
- .no_dynamic_id = 1,
-};
-
-static struct usb_serial_driver hp49gp_device = {
- .driver = {
- .owner = THIS_MODULE,
- .name = "hp4X",
- },
- .id_table = id_table,
- .usb_driver = &hp49gp_driver,
- .num_ports = 1,
-};
-
-static int __init hp49gp_init(void)
-{
- int retval;
- retval = usb_serial_register(&hp49gp_device);
- if (retval)
- goto failed_usb_serial_register;
- retval = usb_register(&hp49gp_driver);
- if (retval)
- goto failed_usb_register;
- printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":"
- DRIVER_DESC "\n");
- return 0;
-failed_usb_register:
- usb_serial_deregister(&hp49gp_device);
-failed_usb_serial_register:
- return retval;
-}
-
-static void __exit hp49gp_exit(void)
-{
- usb_deregister(&hp49gp_driver);
- usb_serial_deregister(&hp49gp_device);
-}
-
-module_init(hp49gp_init);
-module_exit(hp49gp_exit);
-
-MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_VERSION(DRIVER_VERSION);
-MODULE_LICENSE("GPL");
diff --git a/drivers/usb/serial/moto_modem.c b/drivers/usb/serial/moto_modem.c
deleted file mode 100644
index cf17183..0000000
--- a/drivers/usb/serial/moto_modem.c
+++ /dev/null
@@ -1,71 +0,0 @@
-/*
- * Motorola USB Phone driver
- *
- * Copyright (C) 2008 Greg Kroah-Hartman <greg at kroah.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * {sigh}
- * Motorola should be using the CDC ACM USB spec, but instead
- * they try to just "do their own thing"... This driver should handle a
- * few phones in which a basic "dumb serial connection" is needed to be
- * able to get a connection through to them.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/tty.h>
-#include <linux/module.h>
-#include <linux/usb.h>
-#include <linux/usb/serial.h>
-
-static const struct usb_device_id id_table[] = {
- { USB_DEVICE(0x05c6, 0x3197) }, /* unknown Motorola phone */
- { USB_DEVICE(0x0c44, 0x0022) }, /* unknown Mororola phone */
- { USB_DEVICE(0x22b8, 0x2a64) }, /* Motorola KRZR K1m */
- { USB_DEVICE(0x22b8, 0x2c64) }, /* Motorola V950 phone */
- { },
-};
-MODULE_DEVICE_TABLE(usb, id_table);
-
-static struct usb_driver moto_driver = {
- .name = "moto-modem",
- .probe = usb_serial_probe,
- .disconnect = usb_serial_disconnect,
- .id_table = id_table,
- .no_dynamic_id = 1,
-};
-
-static struct usb_serial_driver moto_device = {
- .driver = {
- .owner = THIS_MODULE,
- .name = "moto-modem",
- },
- .id_table = id_table,
- .num_ports = 1,
-};
-
-static int __init moto_init(void)
-{
- int retval;
-
- retval = usb_serial_register(&moto_device);
- if (retval)
- return retval;
- retval = usb_register(&moto_driver);
- if (retval)
- usb_serial_deregister(&moto_device);
- return retval;
-}
-
-static void __exit moto_exit(void)
-{
- usb_deregister(&moto_driver);
- usb_serial_deregister(&moto_device);
-}
-
-module_init(moto_init);
-module_exit(moto_exit);
-MODULE_LICENSE("GPL");
diff --git a/drivers/usb/serial/siemens_mpi.c b/drivers/usb/serial/siemens_mpi.c
deleted file mode 100644
index cb8195c..0000000
--- a/drivers/usb/serial/siemens_mpi.c
+++ /dev/null
@@ -1,77 +0,0 @@
-/*
- * Siemens USB-MPI Serial USB driver
- *
- * Copyright (C) 2005 Thomas Hergenhahn <thomas.hergenhahn at suse.de>
- * Copyright (C) 2005,2008 Greg Kroah-Hartman <gregkh at suse.de>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License version
- * 2 as published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/tty.h>
-#include <linux/module.h>
-#include <linux/usb.h>
-#include <linux/usb/serial.h>
-
-/* Version Information */
-#define DRIVER_VERSION "Version 0.1 09/26/2005"
-#define DRIVER_AUTHOR "Thomas Hergenhahn at web.de http://libnodave.sf.net"
-#define DRIVER_DESC "Driver for Siemens USB/MPI adapter"
-
-
-static const struct usb_device_id id_table[] = {
- /* Vendor and product id for 6ES7-972-0CB20-0XA0 */
- { USB_DEVICE(0x908, 0x0004) },
- { },
-};
-MODULE_DEVICE_TABLE(usb, id_table);
-
-static struct usb_driver siemens_usb_mpi_driver = {
- .name = "siemens_mpi",
- .probe = usb_serial_probe,
- .disconnect = usb_serial_disconnect,
- .id_table = id_table,
-};
-
-static struct usb_serial_driver siemens_usb_mpi_device = {
- .driver = {
- .owner = THIS_MODULE,
- .name = "siemens_mpi",
- },
- .id_table = id_table,
- .num_ports = 1,
-};
-
-static int __init siemens_usb_mpi_init(void)
-{
- int retval;
-
- retval = usb_serial_register(&siemens_usb_mpi_device);
- if (retval)
- goto failed_usb_serial_register;
- retval = usb_register(&siemens_usb_mpi_driver);
- if (retval)
- goto failed_usb_register;
- printk(KERN_INFO DRIVER_DESC "\n");
- printk(KERN_INFO DRIVER_VERSION " " DRIVER_AUTHOR "\n");
- return retval;
-failed_usb_register:
- usb_serial_deregister(&siemens_usb_mpi_device);
-failed_usb_serial_register:
- return retval;
-}
-
-static void __exit siemens_usb_mpi_exit(void)
-{
- usb_deregister(&siemens_usb_mpi_driver);
- usb_serial_deregister(&siemens_usb_mpi_device);
-}
-
-module_init(siemens_usb_mpi_init);
-module_exit(siemens_usb_mpi_exit);
-MODULE_AUTHOR(DRIVER_AUTHOR);
-MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_LICENSE("GPL");
diff --git a/drivers/usb/serial/usb-serial-dummy.c b/drivers/usb/serial/usb-serial-dummy.c
new file mode 100644
index 0000000..1e2d0a2
--- /dev/null
+++ b/drivers/usb/serial/usb-serial-dummy.c
@@ -0,0 +1,92 @@
+/*
+ * Dummy USB-serial cable driver
+ *
+ * Copyright (C) 2008-2010 Marek Vasut <marek.vasut at gmail.com>
+ *
+ * This driver is used to implement USB-serial like behaviour over dummy USB
+ * cables. These are used in the following devices:
+ * Funsoft Serial USB driver (was funsoft)
+ * Genesys Logic GL620USB USB Laplink cable (was gl620)
+ * HP4x (48/49) Serial cable (was hp4x)
+ * Motorola phones (was moto_modem)
+ * Siemens USB-MPI Serial USB driver (was siemens_mpi)
+ * ViVOpay USB Serial Driver (was vivopay-serial)
+ * ZIO Motherboard USB driver (was zio)
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/tty.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include <linux/usb/serial.h>
+
+struct usb_device_id usb_serial_dummy_id_table[] = {
+ { USB_DEVICE(0x05e3, 0x0501) }, /* Genesys Logic GL620USB USB Laplink */
+ { USB_DEVICE(0x03f0, 0x0121) }, /* HP4x Calculators Serial USB driver */
+ { USB_DEVICE(0x1cbe, 0x0103) }, /* ZIO Motherboard USB driver */
+ { USB_DEVICE(0x1404, 0xcddc) }, /* Funsoft Serial USB driver */
+ { USB_DEVICE(0x1d5f, 0x1004) }, /* ViVOpay USB Serial Driver */
+ { USB_DEVICE(0x05c6, 0x3197) }, /* unknown Motorola phone */
+ { USB_DEVICE(0x0c44, 0x0022) }, /* unknown Mororola phone */
+ { USB_DEVICE(0x22b8, 0x2a64) }, /* Motorola KRZR K1m */
+ { USB_DEVICE(0x22b8, 0x2c64) }, /* Motorola V950 phone */
+ { USB_DEVICE(0x0908, 0x0004) }, /* Siemens USB-MPI Serial USB driver */
+ { },
+};
+
+MODULE_DEVICE_TABLE(usb, usb_serial_dummy_id_table);
+
+struct usb_driver usb_serial_dummy_usb_driver = {
+ .name = "usb-serial-dummy",
+ .probe = usb_serial_probe,
+ .disconnect = usb_serial_disconnect,
+ .id_table = usb_serial_dummy_id_table,
+ .no_dynamic_id = 1,
+};
+
+struct usb_serial_driver usb_serial_dummy_serial_driver = {
+ .driver = {
+ .name = "usb-serial-dummy",
+ .owner = THIS_MODULE,
+ },
+ .description = "Dummy USB-serial cable",
+ .usb_driver = &usb_serial_dummy_usb_driver,
+ .id_table = usb_serial_dummy_id_table,
+ .num_ports = 1,
+};
+
+int __init usb_serial_dummy_init(void)
+{
+ int ret;
+
+ ret = usb_serial_register(&usb_serial_dummy_serial_driver);
+ if (ret)
+ goto err1;
+ ret = usb_register(&usb_serial_dummy_usb_driver);
+ if (ret)
+ goto err2;
+
+ return 0;
+err2:
+ usb_serial_deregister(&usb_serial_dummy_serial_driver);
+err1:
+ return ret;
+}
+
+void __exit usb_serial_dummy_exit(void)
+{
+ usb_deregister(&usb_serial_dummy_usb_driver);
+ usb_serial_deregister(&usb_serial_dummy_serial_driver);
+}
+
+module_init(usb_serial_dummy_init);
+module_exit(usb_serial_dummy_exit);
+
+MODULE_AUTHOR("Marek Vasut <marek.vasut at gmail.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Driver for dummy USB-serial cables");
diff --git a/drivers/usb/serial/vivopay-serial.c b/drivers/usb/serial/vivopay-serial.c
deleted file mode 100644
index f719d00..0000000
--- a/drivers/usb/serial/vivopay-serial.c
+++ /dev/null
@@ -1,76 +0,0 @@
-/*
- * Copyright (C) 2001-2005 Greg Kroah-Hartman (greg at kroah.com)
- * Copyright (C) 2009 Outpost Embedded, LLC
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/tty.h>
-#include <linux/module.h>
-#include <linux/usb.h>
-#include <linux/usb/serial.h>
-
-
-#define DRIVER_VERSION "v1.0"
-#define DRIVER_DESC "ViVOpay USB Serial Driver"
-
-#define VIVOPAY_VENDOR_ID 0x1d5f
-
-
-static struct usb_device_id id_table [] = {
- /* ViVOpay 8800 */
- { USB_DEVICE(VIVOPAY_VENDOR_ID, 0x1004) },
- { },
-};
-
-MODULE_DEVICE_TABLE(usb, id_table);
-
-static struct usb_driver vivopay_serial_driver = {
- .name = "vivopay-serial",
- .probe = usb_serial_probe,
- .disconnect = usb_serial_disconnect,
- .id_table = id_table,
- .no_dynamic_id = 1,
-};
-
-static struct usb_serial_driver vivopay_serial_device = {
- .driver = {
- .owner = THIS_MODULE,
- .name = "vivopay-serial",
- },
- .id_table = id_table,
- .usb_driver = &vivopay_serial_driver,
- .num_ports = 1,
-};
-
-static int __init vivopay_serial_init(void)
-{
- int retval;
- retval = usb_serial_register(&vivopay_serial_device);
- if (retval)
- goto failed_usb_serial_register;
- retval = usb_register(&vivopay_serial_driver);
- if (retval)
- goto failed_usb_register;
- printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":"
- DRIVER_DESC "\n");
- return 0;
-failed_usb_register:
- usb_serial_deregister(&vivopay_serial_device);
-failed_usb_serial_register:
- return retval;
-}
-
-static void __exit vivopay_serial_exit(void)
-{
- usb_deregister(&vivopay_serial_driver);
- usb_serial_deregister(&vivopay_serial_device);
-}
-
-module_init(vivopay_serial_init);
-module_exit(vivopay_serial_exit);
-
-MODULE_AUTHOR("Forest Bond <forest.bond at outpostembedded.com>");
-MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_VERSION(DRIVER_VERSION);
-MODULE_LICENSE("GPL");
diff --git a/drivers/usb/serial/zio.c b/drivers/usb/serial/zio.c
deleted file mode 100644
index f579672..0000000
--- a/drivers/usb/serial/zio.c
+++ /dev/null
@@ -1,64 +0,0 @@
-/*
- * ZIO Motherboard USB driver
- *
- * Copyright (C) 2010 Zilogic Systems <code at zilogic.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License version
- * 2 as published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/tty.h>
-#include <linux/module.h>
-#include <linux/usb.h>
-#include <linux/usb/serial.h>
-#include <linux/uaccess.h>
-
-static const struct usb_device_id id_table[] = {
- { USB_DEVICE(0x1CBE, 0x0103) },
- { },
-};
-MODULE_DEVICE_TABLE(usb, id_table);
-
-static struct usb_driver zio_driver = {
- .name = "zio",
- .probe = usb_serial_probe,
- .disconnect = usb_serial_disconnect,
- .id_table = id_table,
- .no_dynamic_id = 1,
-};
-
-static struct usb_serial_driver zio_device = {
- .driver = {
- .owner = THIS_MODULE,
- .name = "zio",
- },
- .id_table = id_table,
- .usb_driver = &zio_driver,
- .num_ports = 1,
-};
-
-static int __init zio_init(void)
-{
- int retval;
-
- retval = usb_serial_register(&zio_device);
- if (retval)
- return retval;
- retval = usb_register(&zio_driver);
- if (retval)
- usb_serial_deregister(&zio_device);
- return retval;
-}
-
-static void __exit zio_exit(void)
-{
- usb_deregister(&zio_driver);
- usb_serial_deregister(&zio_device);
-}
-
-module_init(zio_init);
-module_exit(zio_exit);
-MODULE_LICENSE("GPL");
--
1.7.1
More information about the linux-arm-kernel
mailing list