[PATCHv9 2.6.34-rc5 4/5] mxc: Add generic USB HW initialization for MX51
Dinh.Nguyen at freescale.com
Dinh.Nguyen at freescale.com
Tue Apr 27 11:18:46 EDT 2010
From: Dinh Nguyen <Dinh.Nguyen at freescale.com>
This patch adds USB HW initializiation code to /plat-mxc/ehci.c.
-Sets some specific PHY settings
Renames mxc_set_usbcontrol to mxc_initialize_usb_hw.
Adds new register bit defines for the USB HW on Freescale
SoCs.
This patch applies to 2.6.34-rc5.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen at freescale.com>
Reviewed-by: Daniel Mack <daniel at caiaq.de>
---
arch/arm/mach-mx5/clock-mx51.c | 1 +
arch/arm/plat-mxc/ehci.c | 100 ++++++++++++++++++++++++++++-
arch/arm/plat-mxc/include/mach/mxc_ehci.h | 14 ++++-
drivers/usb/host/ehci-mxc.c | 4 +-
4 files changed, 114 insertions(+), 5 deletions(-)
diff --git a/arch/arm/mach-mx5/clock-mx51.c b/arch/arm/mach-mx5/clock-mx51.c
index dcca330..1fe40e1 100644
--- a/arch/arm/mach-mx5/clock-mx51.c
+++ b/arch/arm/mach-mx5/clock-mx51.c
@@ -16,6 +16,7 @@
#include <linux/io.h>
#include <asm/clkdev.h>
+#include <asm/div64.h>
#include <mach/hardware.h>
#include <mach/common.h>
diff --git a/arch/arm/plat-mxc/ehci.c b/arch/arm/plat-mxc/ehci.c
index cb0b638..2a86461 100644
--- a/arch/arm/plat-mxc/ehci.c
+++ b/arch/arm/plat-mxc/ehci.c
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2009 Daniel Mack <daniel at caiaq.de>
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
@@ -50,7 +51,26 @@
#define MX35_H1_TLL_BIT (1 << 5)
#define MX35_H1_USBTE_BIT (1 << 4)
-int mxc_set_usbcontrol(int port, unsigned int flags)
+#define MXC_OTG_OFFSET 0
+#define MXC_H1_OFFSET 0x200
+
+/* USB_CTRL */
+#define MXC_OTG_UCTRL_OWIE_BIT (1 << 27) /* OTG wakeup intr enable */
+#define MXC_OTG_UCTRL_OPM_BIT (1 << 24) /* OTG power mask */
+#define MXC_H1_UCTRL_H1UIE_BIT (1 << 12) /* Host1 ULPI interrupt enable */
+#define MXC_H1_UCTRL_H1WIE_BIT (1 << 11) /* HOST1 wakeup intr enable */
+#define MXC_H1_UCTRL_H1PM_BIT (1 << 8) /* HOST1 power mask */
+
+/* USB_PHY_CTRL_FUNC */
+#define MXC_OTG_PHYCTRL_OC_DIS_BIT (1 << 8) /* OTG Disable Overcurrent Event */
+#define MXC_H1_OC_DIS_BIT (1 << 5) /* UH1 Disable Overcurrent Event */
+
+#define MXC_USBCMD_OFFSET 0x140
+
+/* USBCMD */
+#define MXC_UCMD_ITC_NO_THRESHOLD_MASK (~(0xff << 16)) /* Interrupt Threshold Control */
+
+int mxc_initialize_usb_hw(int port, unsigned int flags)
{
unsigned int v;
#ifdef CONFIG_ARCH_MX3
@@ -186,9 +206,85 @@ int mxc_set_usbcontrol(int port, unsigned int flags)
return 0;
}
#endif /* CONFIG_MACH_MX27 */
+#ifdef CONFIG_ARCH_MX51
+ if (cpu_is_mx51()) {
+ void __iomem *usb_base;
+ u32 usbotg_base;
+ u32 usbother_base;
+ int ret = 0;
+
+ usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
+
+ switch (port) {
+ case 0: /* OTG port */
+ usbotg_base = usb_base + MXC_OTG_OFFSET;
+ break;
+ case 1: /* Host 1 port */
+ usbotg_base = usb_base + MXC_H1_OFFSET;
+ break;
+ default:
+ printk(KERN_ERR"%s no such port %d\n", __func__, port);
+ ret = -ENOENT;
+ goto error;
+ }
+ usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
+
+ switch (port) {
+ case 0: /*OTG port */
+ if (flags & MXC_EHCI_INTERNAL_PHY) {
+ v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
+
+ if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ v |= (MXC_OTG_PHYCTRL_OC_DIS_BIT | MXC_OTG_UCTRL_OPM_BIT); /* OC/USBPWR is not used */
+ else
+ v &= ~(MXC_OTG_PHYCTRL_OC_DIS_BIT | MXC_OTG_UCTRL_OPM_BIT); /* OC/USBPWR is used */
+ __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
+
+ v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET);
+ if (flags & MXC_EHCI_WAKEUP_ENABLED)
+ v |= MXC_OTG_UCTRL_OWIE_BIT;/* OTG wakeup enable */
+ else
+ v &= ~MXC_OTG_UCTRL_OWIE_BIT;/* OTG wakeup disable */
+ __raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
+ }
+ break;
+ case 1: /* Host 1 */
+ /*Host ULPI */
+ v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET);
+ if (flags & MXC_EHCI_WAKEUP_ENABLED)
+ v &= ~(MXC_H1_UCTRL_H1WIE_BIT | MXC_H1_UCTRL_H1UIE_BIT);/* HOST1 wakeup/ULPI intr disable */
+ else
+ v &= ~(MXC_H1_UCTRL_H1WIE_BIT | MXC_H1_UCTRL_H1UIE_BIT);/* HOST1 wakeup/ULPI intr disable */
+
+ if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used*/
+ else
+ v |= MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used*/
+ __raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
+
+ v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
+ if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ v &= ~MXC_H1_OC_DIS_BIT; /* OC is used */
+ else
+ v |= MXC_H1_OC_DIS_BIT; /* OC is not used */
+ __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
+
+ v = __raw_readl(usbotg_base + MXC_USBCMD_OFFSET);
+ if (flags & MXC_EHCI_ITC_NO_THRESHOLD)
+ /* Interrupt Threshold Control:Immediate (no threshold) */
+ v &= MXC_UCMD_ITC_NO_THRESHOLD_MASK;
+ __raw_writel(v, usbotg_base + MXC_USBCMD_OFFSET);
+ break;
+ }
+
+error:
+ iounmap(usb_base);
+ return ret;
+ }
+#endif
printk(KERN_WARNING
"%s() unable to setup USBCONTROL for this CPU\n", __func__);
return -EINVAL;
}
-EXPORT_SYMBOL(mxc_set_usbcontrol);
+EXPORT_SYMBOL(mxc_initialize_usb_hw);
diff --git a/arch/arm/plat-mxc/include/mach/mxc_ehci.h b/arch/arm/plat-mxc/include/mach/mxc_ehci.h
index 4b9b836..7fc5f99 100644
--- a/arch/arm/plat-mxc/include/mach/mxc_ehci.h
+++ b/arch/arm/plat-mxc/include/mach/mxc_ehci.h
@@ -25,6 +25,18 @@
#define MXC_EHCI_INTERNAL_PHY (1 << 7)
#define MXC_EHCI_IPPUE_DOWN (1 << 8)
#define MXC_EHCI_IPPUE_UP (1 << 9)
+#define MXC_EHCI_WAKEUP_ENABLED (1 << 10)
+#define MXC_EHCI_ITC_NO_THRESHOLD (1 << 11)
+
+#define MXC_USBCTRL_OFFSET 0
+#define MXC_USB_PHY_CTR_FUNC_OFFSET 0x8
+#define MXC_USB_PHY_CTR_FUNC2_OFFSET 0xc
+
+#define MX5_USBOTHER_REGS_OFFSET 0x800
+
+/* USB_PHY_CTRL_FUNC2*/
+#define MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK 0x3
+#define MX5_USB_UTMI_PHYCTRL1_PLLDIV_SHIFT 0
struct mxc_usbh_platform_data {
int (*init)(struct platform_device *pdev);
@@ -35,7 +47,7 @@ struct mxc_usbh_platform_data {
struct otg_transceiver *otg;
};
-int mxc_set_usbcontrol(int port, unsigned int flags);
+int mxc_initialize_usb_hw(int port, unsigned int flags);
#endif /* __INCLUDE_ASM_ARCH_MXC_EHCI_H */
diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
index ead59f4..544ccfd 100644
--- a/drivers/usb/host/ehci-mxc.c
+++ b/drivers/usb/host/ehci-mxc.c
@@ -199,8 +199,8 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
writel(pdata->portsc, hcd->regs + PORTSC_OFFSET);
mdelay(10);
- /* setup USBCONTROL. */
- ret = mxc_set_usbcontrol(pdev->id, pdata->flags);
+ /* setup specific usb hw */
+ ret = mxc_initialize_usb_hw(pdev->id, pdata->flags);
if (ret < 0)
goto err_init;
--
1.6.0.4
More information about the linux-arm-kernel
mailing list