[PATCH 3/3 v2] at91/atmel-mci: inclusion of sd/mmc driver in at91sam9g45 chip and board
Yegor Yefremov
yegor_sub1 at visionsystems.de
Mon Oct 26 04:15:15 EDT 2009
Nicolas Ferre wrote:
> This adds the support of atmel-mci sd/mmc driver in at91sam9g45 devices and
> board files. This also configures the DMA controller slave interface for
> at_hdmac dmaengine driver.
>
> Signed-off-by: Nicolas Ferre <nicolas.ferre at atmel.com>
> ---
> arch/arm/mach-at91/at91sam9g45_devices.c | 164 ++++++++++++++++++++++++++++++
> arch/arm/mach-at91/board-sam9m10g45ek.c | 24 +++++
> drivers/mmc/host/Kconfig | 2 +-
> 3 files changed, 189 insertions(+), 1 deletions(-)
>
> diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
> index d581cff..f341b7e 100644
> --- a/arch/arm/mach-at91/at91sam9g45_devices.c
> +++ b/arch/arm/mach-at91/at91sam9g45_devices.c
> @@ -24,7 +24,10 @@
> #include <mach/at91sam9g45.h>
> #include <mach/at91sam9g45_matrix.h>
> #include <mach/at91sam9_smc.h>
> +
> #include <mach/at_hdmac.h>
> +#include <mach/atmel-mci.h>
> +#include <linux/atmel-mci.h>
>
> #include "generic.h"
>
> @@ -294,6 +297,167 @@ void __init at91_add_device_eth(struct at91_eth_data *data) {}
>
>
> /* --------------------------------------------------------------------
> + * MMC / SD
> + * -------------------------------------------------------------------- */
> +
> +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
> +static u64 mmc_dmamask = DMA_BIT_MASK(32);
> +static struct mci_platform_data mmc0_data, mmc1_data;
> +
> +static struct resource mmc0_resources[] = {
> + [0] = {
> + .start = AT91SAM9G45_BASE_MCI0,
> + .end = AT91SAM9G45_BASE_MCI0 + SZ_16K - 1,
> + .flags = IORESOURCE_MEM,
> + },
> + [1] = {
> + .start = AT91SAM9G45_ID_MCI0,
> + .end = AT91SAM9G45_ID_MCI0,
> + .flags = IORESOURCE_IRQ,
> + },
> +};
> +
> +static struct platform_device at91sam9g45_mmc0_device = {
> + .name = "atmel_mci",
> + .id = 0,
> + .dev = {
> + .dma_mask = &mmc_dmamask,
> + .coherent_dma_mask = DMA_BIT_MASK(32),
> + .platform_data = &mmc0_data,
> + },
> + .resource = mmc0_resources,
> + .num_resources = ARRAY_SIZE(mmc0_resources),
> +};
> +
> +static struct resource mmc1_resources[] = {
> + [0] = {
> + .start = AT91SAM9G45_BASE_MCI1,
> + .end = AT91SAM9G45_BASE_MCI1 + SZ_16K - 1,
> + .flags = IORESOURCE_MEM,
> + },
> + [1] = {
> + .start = AT91SAM9G45_ID_MCI1,
> + .end = AT91SAM9G45_ID_MCI1,
> + .flags = IORESOURCE_IRQ,
> + },
> +};
> +
> +static struct platform_device at91sam9g45_mmc1_device = {
> + .name = "atmel_mci",
> + .id = 1,
> + .dev = {
> + .dma_mask = &mmc_dmamask,
> + .coherent_dma_mask = DMA_BIT_MASK(32),
> + .platform_data = &mmc1_data,
> + },
> + .resource = mmc1_resources,
> + .num_resources = ARRAY_SIZE(mmc1_resources),
> +};
> +
> +/* Consider only one slot : slot 0 */
> +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
> +{
> +
> + if (!data)
> + return;
> +
> + /* Must have at least one usable slot */
> + if (!data->slot[0].bus_width)
> + return;
> +
> +#if defined(CONFIG_MMC_ATMELMCI_DMA)
> + {
> + struct mci_dma_data *slave;
> +
> + slave = kzalloc(sizeof(struct mci_dma_data), GFP_KERNEL);
> +
> + /* DMA slave channel configuration */
> + slave->sdata.dma_dev = &at_hdmac_device.dev;
> + slave->sdata.reg_width = DW_DMA_SLAVE_WIDTH_32BIT;
slave->sdata.reg_width = AT_DMA_SLAVE_WIDTH_32BIT;
> + slave->sdata.cfg = ATC_FIFOCFG_HALFFIFO
> + | ATC_SRC_H2SEL_HW | ATC_DST_H2SEL_HW;
> + slave->sdata.ctrla = ATC_SCSIZE_16 | ATC_DCSIZE_16;
> + if (mmc_id == 0) /* MCI0 */
> + slave->sdata.cfg |= ATC_SRC_PER(AT_DMA_ID_MCI0)
> + | ATC_DST_PER(AT_DMA_ID_MCI0);
> +
> + else /* MCI1 */
> + slave->sdata.cfg |= ATC_SRC_PER(AT_DMA_ID_MCI1)
> + | ATC_DST_PER(AT_DMA_ID_MCI1);
> +
> + data->dma_slave = slave;
> + }
> +#endif
> +
> +
> + /* input/irq */
> + if (data->slot[0].detect_pin) {
> + at91_set_gpio_input(data->slot[0].detect_pin, 1);
> + at91_set_deglitch(data->slot[0].detect_pin, 1);
> + }
> + if (data->slot[0].wp_pin)
> + at91_set_gpio_input(data->slot[0].wp_pin, 1);
> +
> + if (mmc_id == 0) { /* MCI0 */
> +
> + /* CLK */
> + at91_set_A_periph(AT91_PIN_PA0, 0);
> +
> + /* CMD */
> + at91_set_A_periph(AT91_PIN_PA1, 1);
> +
> + /* DAT0, maybe DAT1..DAT3 and maybe DAT4..DAT7 */
> + at91_set_A_periph(AT91_PIN_PA2, 1);
> + if (data->slot[0].bus_width == 4) {
> + at91_set_A_periph(AT91_PIN_PA3, 1);
> + at91_set_A_periph(AT91_PIN_PA4, 1);
> + at91_set_A_periph(AT91_PIN_PA5, 1);
> + if (data->slot[0].bus_width == 8) {
> + at91_set_A_periph(AT91_PIN_PA6, 1);
> + at91_set_A_periph(AT91_PIN_PA7, 1);
> + at91_set_A_periph(AT91_PIN_PA8, 1);
> + at91_set_A_periph(AT91_PIN_PA9, 1);
> + }
> + }
> +
> + mmc0_data = *data;
> + at91_clock_associate("mci0_clk", &at91sam9g45_mmc0_device.dev, "mci_clk");
> + platform_device_register(&at91sam9g45_mmc0_device);
> +
> + } else { /* MCI1 */
> +
> + /* CLK */
> + at91_set_A_periph(AT91_PIN_PA31, 0);
> +
> + /* CMD */
> + at91_set_A_periph(AT91_PIN_PA22, 1);
> +
> + /* DAT0, maybe DAT1..DAT3 and maybe DAT4..DAT7 */
> + at91_set_A_periph(AT91_PIN_PA23, 1);
> + if (data->slot[0].bus_width == 4) {
> + at91_set_A_periph(AT91_PIN_PA24, 1);
> + at91_set_A_periph(AT91_PIN_PA25, 1);
> + at91_set_A_periph(AT91_PIN_PA26, 1);
> + if (data->slot[0].bus_width == 8) {
> + at91_set_A_periph(AT91_PIN_PA27, 1);
> + at91_set_A_periph(AT91_PIN_PA28, 1);
> + at91_set_A_periph(AT91_PIN_PA29, 1);
> + at91_set_A_periph(AT91_PIN_PA30, 1);
> + }
> + }
> +
> + mmc1_data = *data;
> + at91_clock_associate("mci1_clk", &at91sam9g45_mmc1_device.dev, "mci_clk");
> + platform_device_register(&at91sam9g45_mmc1_device);
> +
> + }
> +}
> +#else
> +void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
> +#endif
> +
> +
> +/* --------------------------------------------------------------------
> * NAND / SmartMedia
> * -------------------------------------------------------------------- */
>
> diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
> index 64c3843..1cce010 100644
> --- a/arch/arm/mach-at91/board-sam9m10g45ek.c
> +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
> @@ -24,6 +24,7 @@
> #include <linux/input.h>
> #include <linux/leds.h>
> #include <linux/clk.h>
> +#include <linux/atmel-mci.h>
>
> #include <mach/hardware.h>
> #include <video/atmel_lcdc.h>
> @@ -99,6 +100,26 @@ static struct spi_board_info ek_spi_devices[] = {
>
>
> /*
> + * MCI (SD/MMC)
> + */
> +static struct mci_platform_data __initdata mci0_data = {
> + .slot[0] = {
> + .bus_width = 4,
> + .detect_pin = AT91_PIN_PD10,
> + .wp_pin = -1,
> + },
> +};
> +
> +static struct mci_platform_data __initdata mci1_data = {
> + .slot[0] = {
> + .bus_width = 4,
> + .detect_pin = AT91_PIN_PD11,
> + .wp_pin = AT91_PIN_PD29,
> + },
> +};
> +
> +
> +/*
> * MACB Ethernet device
> */
> static struct at91_eth_data __initdata ek_macb_data = {
> @@ -370,6 +391,9 @@ static void __init ek_board_init(void)
> at91_add_device_usba(&ek_usba_udc_data);
> /* SPI */
> at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
> + /* MMC */
> + at91_add_device_mci(0, &mci0_data);
> + at91_add_device_mci(1, &mci1_data);
> /* Ethernet */
> at91_add_device_eth(&ek_macb_data);
> /* NAND */
> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
> index 432ae83..b4aeb9d 100644
> --- a/drivers/mmc/host/Kconfig
> +++ b/drivers/mmc/host/Kconfig
> @@ -188,7 +188,7 @@ endchoice
>
> config MMC_ATMELMCI_DMA
> bool "Atmel MCI DMA support (EXPERIMENTAL)"
> - depends on MMC_ATMELMCI && AVR32 && DMA_ENGINE && EXPERIMENTAL
> + depends on MMC_ATMELMCI && (AVR32 || ARCH_AT91SAM9G45) && DMA_ENGINE && EXPERIMENTAL
> help
> Say Y here to have the Atmel MCI driver use a DMA engine to
> do data transfers and thus increase the throughput and
Signed-off-by: Yegor Yefremov <yegorslists at googlemail.com>
More information about the linux-arm-kernel
mailing list