[PATCH] at91: support for eco920
Uwe Kleine-König
u.kleine-koenig at pengutronix.de
Wed Oct 21 04:41:27 EDT 2009
CONFIG_MACH_ECO920 is enabled in at91rm9200dk_defconfig. The name is
wrong, but this is better than adding another defconfig or don't get
compile coverage at all.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig at pengutronix.de>
Cc: Sascha Hauer <s.hauer at pengutronix.de>
---
Hello,
I just added CONFIG_MACH_ECO920=y, all devices but mmc are already
enabled. And for my environment I need NFS and IP_PNP_DHCP.
But as I only target for build coverage, it's enough this way.
Best regards
Uwe
arch/arm/configs/at91rm9200dk_defconfig | 1 +
arch/arm/mach-at91/Kconfig | 5 +
arch/arm/mach-at91/Makefile | 1 +
arch/arm/mach-at91/board-eco920.c | 158 +++++++++++++++++++++++++++++++
4 files changed, 165 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-at91/board-eco920.c
diff --git a/arch/arm/configs/at91rm9200dk_defconfig b/arch/arm/configs/at91rm9200dk_defconfig
index 238b218..c97e102 100644
--- a/arch/arm/configs/at91rm9200dk_defconfig
+++ b/arch/arm/configs/at91rm9200dk_defconfig
@@ -120,6 +120,7 @@ CONFIG_ARCH_AT91RM9200DK=y
# CONFIG_MACH_CARMEVA is not set
# CONFIG_MACH_KB9200 is not set
# CONFIG_MACH_ATEB9200 is not set
+CONFIG_MACH_ECO920=y
#
# AT91RM9200 Feature Selections
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index e35d54d..7878e33 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -163,6 +163,11 @@ config MACH_CPUAT91
Select this if you are using the Eukrea Electromatique's
CPUAT91 board <http://www.eukrea.com/>.
+config MACH_ECO920
+ bool "eco920"
+ help
+ Select this if you are using the eco920 board
+
endif
# ----------------------------------------------------------
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index ada440a..9ad357f 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -35,6 +35,7 @@ obj-$(CONFIG_MACH_PICOTUX2XX) += board-picotux200.o
obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o
obj-$(CONFIG_MACH_YL9200) += board-yl-9200.o
obj-$(CONFIG_MACH_CPUAT91) += board-cpuat91.o
+obj-$(CONFIG_MACH_ECO920) += board-eco920.o
# AT91SAM9260 board-specific support
obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c
new file mode 100644
index 0000000..974f175
--- /dev/null
+++ b/arch/arm/mach-at91/board-eco920.c
@@ -0,0 +1,158 @@
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/mach-types.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91rm9200_mc.h>
+#include "generic.h"
+
+static void __init eco920_map_io(void)
+{
+ at91rm9200_initialize(18432000, AT91RM9200_PQFP);
+
+ /* Setup the LEDs */
+ at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
+
+ /* DBGU on ttyS0. (Rx & Tx only */
+ at91_register_uart(0, 0, 0);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
+}
+
+static void __init eco920_init_irq(void)
+{
+ at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata eco920_eth_data = {
+ .phy_irq_pin = AT91_PIN_PC2,
+ .is_rmii = 1,
+};
+
+static struct at91_usbh_data __initdata eco920_usbh_data = {
+ .ports = 1,
+};
+
+static struct at91_udc_data __initdata eco920_udc_data = {
+ .vbus_pin = AT91_PIN_PB12,
+ .pullup_pin = AT91_PIN_PB13,
+};
+
+static struct at91_mmc_data __initdata eco920_mmc_data = {
+ .slot_b = 0,
+ .wire4 = 0,
+};
+
+static struct physmap_flash_data eco920_flash_data = {
+ .width = 2,
+};
+
+static struct resource eco920_flash_resource = {
+ .start = 0x11000000,
+ .end = 0x11ffffff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device eco920_flash = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &eco920_flash_data,
+ },
+ .resource = &eco920_flash_resource,
+ .num_resources = 1,
+};
+
+static struct resource at91_beeper_resources[] = {
+ [0] = {
+ .start = AT91RM9200_BASE_TC3,
+ .end = AT91RM9200_BASE_TC3 + 0x39,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device at91_beeper = {
+ .name = "at91_beeper",
+ .id = 0,
+ .resource = at91_beeper_resources,
+ .num_resources = ARRAY_SIZE(at91_beeper_resources),
+};
+
+static struct spi_board_info eco920_spi_devices[] = {
+ { /* CAN controller */
+ .modalias = "tlv5638",
+ .chip_select = 3,
+ .max_speed_hz = 20 * 1000 * 1000,
+ .mode = SPI_CPHA,
+ },
+};
+
+static void __init eco920_board_init(void)
+{
+ at91_add_device_serial();
+ at91_add_device_eth(&eco920_eth_data);
+ at91_add_device_usbh(&eco920_usbh_data);
+ at91_add_device_udc(&eco920_udc_data);
+
+ at91_add_device_mmc(0, &eco920_mmc_data);
+ platform_device_register(&eco920_flash);
+
+ at91_sys_write(AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1)
+ | AT91_SMC_RWSETUP_(1)
+ | AT91_SMC_DBW_8
+ | AT91_SMC_WSEN
+ | AT91_SMC_NWS_(15));
+
+ at91_set_A_periph(AT91_PIN_PC6, 1);
+
+ at91_set_gpio_input(AT91_PIN_PA23, 0);
+ at91_set_deglitch(AT91_PIN_PA23, 1);
+
+/* Initialization of the Static Memory Controller for Chip Select 3 */
+ at91_sys_write(AT91_SMC_CSR(3),
+ AT91_SMC_DBW_16 | /* 16 bit */
+ AT91_SMC_WSEN |
+ AT91_SMC_NWS_(5) | /* wait states */
+ AT91_SMC_TDF_(1) /* float time */
+ );
+
+ at91_clock_associate("tc3_clk", &at91_beeper.dev, "at91_beeper");
+ at91_set_B_periph(AT91_PIN_PB6, 0);
+ platform_device_register(&at91_beeper);
+
+ at91_add_device_spi(eco920_spi_devices, ARRAY_SIZE(eco920_spi_devices));
+}
+
+MACHINE_START(ECO920, "eco920")
+ /* Maintainer: Sascha Hauer */
+ .phys_io = AT91_BASE_SYS,
+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+ .boot_params = AT91_SDRAM_BASE + 0x100,
+ .timer = &at91rm9200_timer,
+ .map_io = eco920_map_io,
+ .init_irq = eco920_init_irq,
+ .init_machine = eco920_board_init,
+MACHINE_END
--
1.6.5
More information about the linux-arm-kernel
mailing list