[RFC] Re-order of PXA-based platforms in Kconfig and Makefile
Eric Miao
eric.y.miao at gmail.com
Sun Oct 11 21:38:02 EDT 2009
On Sun, Oct 11, 2009 at 3:20 PM, Mike Rapoport <mike at compulab.co.il> wrote:
> Eric
>
> Eric Miao wrote:
>> All,
>>
>> I've listed almost all the PXA based platforms currently existing in mainline
>> kernel as below. Due to the naming mess in Kconfig and Makefile, I'd like to
>> get them sorted in the following order:
>>
>> 1. By category:
>> Intel/Marvell Dev Platforms, followed by 3rd party platforms, followed
>> by end-user products (this is to ensure the commonly referenced platforms
>> will appear first)
>>
>> 2. By vendor name in alphabetic within each category
>> (this is to ensure code reuse and similar platforms can be grouped as
>> much as possible)
>>
>> Patch is attached, and any problems, please let me know.
>
> I'd also add "comment <platform type>" to the Kconfig. This will make it
> slightly more readable.
Good suggestion, patch modified as attached.
-------------- next part --------------
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index 28f0260..ce52fac 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -31,216 +31,144 @@ endmenu
endif
-config ARCH_GUMSTIX
- bool "Gumstix XScale 255 boards"
- select PXA25x
- help
- Say Y here if you intend to run this kernel on
- Basix, Connex, ws-200ax, ws-400ax systems
-
-choice
- prompt "Gumstix Carrier/Expansion Board"
- depends on ARCH_GUMSTIX
-
-config GUMSTIX_AM200EPD
- bool "Enable AM200EPD board support"
-
-config GUMSTIX_AM300EPD
- bool "Enable AM300EPD board support"
-
-endchoice
-
-config MACH_INTELMOTE2
- bool "Intel Mote 2 Platform"
- select PXA27x
- select IWMMXT
- select PXA_HAVE_BOARD_IRQS
-
-config MACH_STARGATE2
- bool "Intel Stargate 2 Platform"
- select PXA27x
- select IWMMXT
- select PXA_HAVE_BOARD_IRQS
+comment "Intel/Marvell Dev Platforms (sorted by hardware release time)"
config ARCH_LUBBOCK
- bool "Intel DBPXA250 Development Platform"
+ bool "Intel DBPXA250 Development Platform (aka Lubbock)"
select PXA25x
select SA1111
select PXA_HAVE_BOARD_IRQS
-config MACH_LOGICPD_PXA270
- bool "LogicPD PXA270 Card Engine Development Platform"
+config MACH_MAINSTONE
+ bool "Intel HCDDBBVA0 Development Platform (aka Mainstone)"
select PXA27x
select HAVE_PWM
select PXA_HAVE_BOARD_IRQS
-config MACH_MAINSTONE
- bool "Intel HCDDBBVA0 Development Platform"
- select PXA27x
+config MACH_ZYLONITE
+ bool "PXA3xx Development Platform (aka Zylonite)"
+ select PXA3xx
+ select PXA_SSP
select HAVE_PWM
select PXA_HAVE_BOARD_IRQS
-config MACH_MP900C
- bool "Nec Mobilepro 900/c"
+config MACH_LITTLETON
+ bool "PXA3xx Form Factor Platform (aka Littleton)"
+ select PXA3xx
+ select PXA_SSP
+
+config MACH_TAVOREVB
+ bool "PXA930 Evaluation Board (aka TavorEVB)"
+ select PXA3xx
+ select CPU_PXA930
+
+config MACH_SAAR
+ bool "PXA930 Handheld Platform (aka SAAR)"
+ select PXA3xx
+ select CPU_PXA930
+
+comment "Third Party Dev Platforms (sorted by vendor name)"
+
+config ARCH_PXA_IDP
+ bool "Accelent Xscale IDP"
select PXA25x
+config ARCH_VIPER
+ bool "Arcom/Eurotech VIPER SBC"
+ select PXA25x
+ select ISA
+ select I2C_GPIO
+ select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
+ select PXA_HAVE_ISA_IRQS
+
config MACH_BALLOON3
bool "Balloon 3 board"
select PXA27x
select IWMMXT
select PXA_HAVE_BOARD_IRQS
-config ARCH_PXA_IDP
- bool "Accelent Xscale IDP"
- select PXA25x
-
-config PXA_SHARPSL
- bool "SHARP Zaurus SL-5600, SL-C7xx and SL-Cxx00 Models"
- select SHARP_SCOOP
- select SHARP_PARAM
+config MACH_CSB726
+ bool "Enable Cogent CSB726 System On a Module"
+ select PXA27x
+ select IWMMXT
help
- Say Y here if you intend to run this kernel on a
- Sharp Zaurus SL-5600 (Poodle), SL-C700 (Corgi),
- SL-C750 (Shepherd), SL-C760 (Husky), SL-C1000 (Akita),
- SL-C3000 (Spitz), SL-C3100 (Borzoi) or SL-C6000x (Tosa)
- handheld computer.
-
-config SHARPSL_PM
- bool
- select APM_EMULATION
+ Say Y here if you intend to run this kernel on a Cogent
+ CSB726 System On Module.
-config CORGI_SSP_DEPRECATED
- bool
- select PXA_SSP
- help
- This option will include corgi_ssp.c and corgi_lcd.c
- that corgi_ts.c and other legacy drivers (corgi_bl.c
- and sharpsl_pm.c) may depend on.
+config CSB726_CSB701
+ bool "Enable supprot for CSB701 baseboard"
+ depends on MACH_CSB726
-config MACH_POODLE
- bool "Enable Sharp SL-5600 (Poodle) Support"
- depends on PXA_SHARPSL
+config MACH_ARMCORE
+ bool "CompuLab CM-X255/CM-X270 modules"
+ select PXA27x
+ select IWMMXT
select PXA25x
- select SHARP_LOCOMO
select PXA_SSP
-config MACH_CORGI
- bool "Enable Sharp SL-C700 (Corgi) Support"
- depends on PXA_SHARPSL
- select PXA25x
- select PXA_SHARP_C7xx
-
-config MACH_SHEPHERD
- bool "Enable Sharp SL-C750 (Shepherd) Support"
- depends on PXA_SHARPSL
- select PXA25x
- select PXA_SHARP_C7xx
-
-config MACH_HUSKY
- bool "Enable Sharp SL-C760 (Husky) Support"
- depends on PXA_SHARPSL
- select PXA25x
- select PXA_SHARP_C7xx
-
-config MACH_AKITA
- bool "Enable Sharp SL-1000 (Akita) Support"
- depends on PXA_SHARPSL
- select PXA27x
- select PXA_SHARP_Cxx00
- select MACH_SPITZ
- select I2C
- select I2C_PXA
-
-config MACH_SPITZ
- bool "Enable Sharp Zaurus SL-3000 (Spitz) Support"
- depends on PXA_SHARPSL
+config MACH_EM_X270
+ bool "CompuLab EM-x270 platform"
select PXA27x
- select PXA_SHARP_Cxx00
-config MACH_BORZOI
- bool "Enable Sharp Zaurus SL-3100 (Borzoi) Support"
- depends on PXA_SHARPSL
+config MACH_EXEDA
+ bool "CompuLab eXeda platform"
select PXA27x
- select PXA_SHARP_Cxx00
-config MACH_TOSA
- bool "Enable Sharp SL-6000x (Tosa) Support"
- depends on PXA_SHARPSL
- select PXA25x
- select PXA_HAVE_BOARD_IRQS
+config MACH_CM_X300
+ bool "CompuLab CM-X300 modules"
+ select PXA3xx
+ select CPU_PXA300
-config ARCH_VIPER
- bool "Arcom/Eurotech VIPER SBC"
+config ARCH_GUMSTIX
+ bool "Gumstix XScale 255 boards"
select PXA25x
- select ISA
- select I2C_GPIO
- select HAVE_PWM
- select PXA_HAVE_BOARD_IRQS
- select PXA_HAVE_ISA_IRQS
+ help
+ Say Y here if you intend to run this kernel on
+ Basix, Connex, ws-200ax, ws-400ax systems
-config ARCH_PXA_ESERIES
- bool "PXA based Toshiba e-series PDAs"
- select PXA25x
- select PXA_HAVE_BOARD_IRQS
+choice
+ prompt "Gumstix Carrier/Expansion Board"
+ depends on ARCH_GUMSTIX
-config MACH_E330
- bool "Toshiba e330"
- default y
- depends on ARCH_PXA_ESERIES
- help
- Say Y here if you intend to run this kernel on a Toshiba
- e330 family PDA.
+config GUMSTIX_AM200EPD
+ bool "Enable AM200EPD board support"
-config MACH_E350
- bool "Toshiba e350"
- default y
- depends on ARCH_PXA_ESERIES
- help
- Say Y here if you intend to run this kernel on a Toshiba
- e350 family PDA.
+config GUMSTIX_AM300EPD
+ bool "Enable AM300EPD board support"
-config MACH_E740
- bool "Toshiba e740"
- default y
- depends on ARCH_PXA_ESERIES
- select FB_W100
- help
- Say Y here if you intend to run this kernel on a Toshiba
- e740 family PDA.
+endchoice
-config MACH_E750
- bool "Toshiba e750"
- default y
- depends on ARCH_PXA_ESERIES
- select FB_W100
- help
- Say Y here if you intend to run this kernel on a Toshiba
- e750 family PDA.
+config MACH_INTELMOTE2
+ bool "Intel Mote 2 Platform"
+ select PXA27x
+ select IWMMXT
+ select PXA_HAVE_BOARD_IRQS
-config MACH_E400
- bool "Toshiba e400"
- default y
- depends on ARCH_PXA_ESERIES
- help
- Say Y here if you intend to run this kernel on a Toshiba
- e400 family PDA.
+config MACH_STARGATE2
+ bool "Intel Stargate 2 Platform"
+ select PXA27x
+ select IWMMXT
+ select PXA_HAVE_BOARD_IRQS
-config MACH_E800
- bool "Toshiba e800"
- default y
- depends on ARCH_PXA_ESERIES
- select FB_W100
+config MACH_XCEP
+ bool "Iskratel Electronics XCEP"
+ select PXA25x
+ select MTD
+ select MTD_PARTITIONS
+ select MTD_PHYSMAP
+ select MTD_CFI_INTELEXT
+ select MTD_CFI
+ select MTD_CHAR
+ select SMC91X
+ select PXA_SSP
help
- Say Y here if you intend to run this kernel on a Toshiba
- e800 family PDA.
+ PXA255 based Single Board Computer with SMC 91C111 ethernet chip and 64 MB of flash.
+ Tuned for usage in Libera instruments for particle accelerators.
config TRIZEPS_PXA
bool "PXA based Keith und Koep Trizeps DIMM-Modules"
-config MACH_H5000
- bool "HP iPAQ h5000"
- select PXA25x
-
config MACH_TRIZEPS4
bool "Keith und Koep Trizeps4 DIMM-Module"
depends on TRIZEPS_PXA
@@ -274,13 +202,38 @@ config TRIZEPS_PCMCIA
help
Enable PCMCIA support for Trizeps modules
-config MACH_EM_X270
- bool "CompuLab EM-x270 platform"
+config MACH_LOGICPD_PXA270
+ bool "LogicPD PXA270 Card Engine Development Platform"
select PXA27x
+ select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
-config MACH_EXEDA
- bool "CompuLab eXeda platform"
+config MACH_PCM027
+ bool "Phytec phyCORE-PXA270 CPU module (PCM-027)"
select PXA27x
+ select IWMMXT
+ select PXA_SSP
+ select PXA_HAVE_BOARD_IRQS
+
+config MACH_PCM990_BASEBOARD
+ bool "PHYTEC PCM-990 development board"
+ select HAVE_PWM
+ depends on MACH_PCM027
+
+choice
+ prompt "display on pcm990"
+ depends on MACH_PCM990_BASEBOARD
+
+config PCM990_DISPLAY_SHARP
+ bool "sharp lq084v1dg21 stn display"
+
+config PCM990_DISPLAY_NEC
+ bool "nec nl6448bc20_18d tft display"
+
+config PCM990_DISPLAY_NONE
+ bool "no display"
+
+endchoice
config MACH_COLIBRI
bool "Toradex Colibri PXA270"
@@ -296,39 +249,7 @@ config MACH_COLIBRI320
select PXA3xx
select CPU_PXA320
-config MACH_ZYLONITE
- bool "PXA3xx Development Platform (aka Zylonite)"
- select PXA3xx
- select PXA_SSP
- select HAVE_PWM
- select PXA_HAVE_BOARD_IRQS
-
-config MACH_LITTLETON
- bool "PXA3xx Form Factor Platform (aka Littleton)"
- select PXA3xx
- select PXA_SSP
-
-config MACH_TAVOREVB
- bool "PXA930 Evaluation Board (aka TavorEVB)"
- select PXA3xx
- select CPU_PXA930
-
-config MACH_SAAR
- bool "PXA930 Handheld Platform (aka SAAR)"
- select PXA3xx
- select CPU_PXA930
-
-config MACH_ARMCORE
- bool "CompuLab CM-X255/CM-X270 modules"
- select PXA27x
- select IWMMXT
- select PXA25x
- select PXA_SSP
-
-config MACH_CM_X300
- bool "CompuLab CM-X300 modules"
- select PXA3xx
- select CPU_PXA300
+comment "End-user Products (sorted by vendor name)"
config MACH_H4700
bool "HP iPAQ hx4700"
@@ -338,6 +259,15 @@ config MACH_H4700
select HAVE_PWM
select PXA_HAVE_BOARD_IRQS
+config MACH_H5000
+ bool "HP iPAQ h5000"
+ select PXA25x
+
+config MACH_HIMALAYA
+ bool "HTC Himalaya Support"
+ select CPU_PXA26x
+ select FB_W100
+
config MACH_MAGICIAN
bool "Enable HTC Magician Support"
select PXA27x
@@ -346,11 +276,6 @@ config MACH_MAGICIAN
select HAVE_PWM
select PXA_HAVE_BOARD_IRQS
-config MACH_HIMALAYA
- bool "HTC Himalaya Support"
- select CPU_PXA26x
- select FB_W100
-
config MACH_MIOA701
bool "Mitac Mio A701 Support"
select PXA27x
@@ -362,13 +287,47 @@ config MACH_MIOA701
MIO A701. Currently there is only basic support
for this PDA.
-config MACH_PCM027
- bool "Phytec phyCORE-PXA270 CPU module (PCM-027)"
+config PXA_EZX
+ bool "Motorola EZX Platform"
select PXA27x
select IWMMXT
- select PXA_SSP
+ select HAVE_PWM
select PXA_HAVE_BOARD_IRQS
+config MACH_EZX_A780
+ bool "Motorola EZX A780"
+ default y
+ depends on PXA_EZX
+
+config MACH_EZX_E680
+ bool "Motorola EZX E680"
+ default y
+ depends on PXA_EZX
+
+config MACH_EZX_A1200
+ bool "Motorola EZX A1200"
+ default y
+ depends on PXA_EZX
+
+config MACH_EZX_A910
+ bool "Motorola EZX A910"
+ default y
+ depends on PXA_EZX
+
+config MACH_EZX_E6
+ bool "Motorola EZX E6"
+ default y
+ depends on PXA_EZX
+
+config MACH_EZX_E2
+ bool "Motorola EZX E2"
+ default y
+ depends on PXA_EZX
+
+config MACH_MP900C
+ bool "Nec Mobilepro 900/c"
+ select PXA25x
+
config ARCH_PXA_PALM
bool "PXA based Palm PDAs"
select HAVE_PWM
@@ -421,6 +380,16 @@ config MACH_PALMZ72
Say Y here if you intend to run this kernel on Palm Zire 72
handheld computer.
+config MACH_PALMLD
+ bool "Palm LifeDrive"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA27x
+ select IWMMXT
+ help
+ Say Y here if you intend to run this kernel on a Palm LifeDrive
+ handheld computer.
+
config PALM_TREO
bool
depends on ARCH_PXA_PALM
@@ -447,99 +416,136 @@ config MACH_TREO680
Say Y here if you intend to run this kernel on Palm Treo 680
smartphone.
-config MACH_PALMLD
- bool "Palm LifeDrive"
- default y
- depends on ARCH_PXA_PALM
- select PXA27x
- select IWMMXT
+config PXA_SHARPSL
+ bool "SHARP Zaurus SL-5600, SL-C7xx and SL-Cxx00 Models"
+ select SHARP_SCOOP
+ select SHARP_PARAM
help
- Say Y here if you intend to run this kernel on a Palm LifeDrive
+ Say Y here if you intend to run this kernel on a
+ Sharp Zaurus SL-5600 (Poodle), SL-C700 (Corgi),
+ SL-C750 (Shepherd), SL-C760 (Husky), SL-C1000 (Akita),
+ SL-C3000 (Spitz), SL-C3100 (Borzoi) or SL-C6000x (Tosa)
handheld computer.
-config MACH_PCM990_BASEBOARD
- bool "PHYTEC PCM-990 development board"
- select HAVE_PWM
- depends on MACH_PCM027
+config SHARPSL_PM
+ bool
+ select APM_EMULATION
-choice
- prompt "display on pcm990"
- depends on MACH_PCM990_BASEBOARD
+config CORGI_SSP_DEPRECATED
+ bool
+ select PXA_SSP
+ help
+ This option will include corgi_ssp.c and corgi_lcd.c
+ that corgi_ts.c and other legacy drivers (corgi_bl.c
+ and sharpsl_pm.c) may depend on.
-config PCM990_DISPLAY_SHARP
- bool "sharp lq084v1dg21 stn display"
+config MACH_POODLE
+ bool "Enable Sharp SL-5600 (Poodle) Support"
+ depends on PXA_SHARPSL
+ select PXA25x
+ select SHARP_LOCOMO
+ select PXA_SSP
-config PCM990_DISPLAY_NEC
- bool "nec nl6448bc20_18d tft display"
+config MACH_CORGI
+ bool "Enable Sharp SL-C700 (Corgi) Support"
+ depends on PXA_SHARPSL
+ select PXA25x
+ select PXA_SHARP_C7xx
-config PCM990_DISPLAY_NONE
- bool "no display"
+config MACH_SHEPHERD
+ bool "Enable Sharp SL-C750 (Shepherd) Support"
+ depends on PXA_SHARPSL
+ select PXA25x
+ select PXA_SHARP_C7xx
-endchoice
+config MACH_HUSKY
+ bool "Enable Sharp SL-C760 (Husky) Support"
+ depends on PXA_SHARPSL
+ select PXA25x
+ select PXA_SHARP_C7xx
-config MACH_CSB726
- bool "Enable Cogent CSB726 System On a Module"
+config MACH_AKITA
+ bool "Enable Sharp SL-1000 (Akita) Support"
+ depends on PXA_SHARPSL
select PXA27x
- select IWMMXT
- help
- Say Y here if you intend to run this kernel on a Cogent
- CSB726 System On Module.
+ select PXA_SHARP_Cxx00
+ select MACH_SPITZ
+ select I2C
+ select I2C_PXA
-config CSB726_CSB701
- bool "Enable supprot for CSB701 baseboard"
- depends on MACH_CSB726
+config MACH_SPITZ
+ bool "Enable Sharp Zaurus SL-3000 (Spitz) Support"
+ depends on PXA_SHARPSL
+ select PXA27x
+ select PXA_SHARP_Cxx00
-config PXA_EZX
- bool "Motorola EZX Platform"
+config MACH_BORZOI
+ bool "Enable Sharp Zaurus SL-3100 (Borzoi) Support"
+ depends on PXA_SHARPSL
select PXA27x
- select IWMMXT
- select HAVE_PWM
+ select PXA_SHARP_Cxx00
+
+config MACH_TOSA
+ bool "Enable Sharp SL-6000x (Tosa) Support"
+ depends on PXA_SHARPSL
+ select PXA25x
select PXA_HAVE_BOARD_IRQS
-config MACH_EZX_A780
- bool "Motorola EZX A780"
- default y
- depends on PXA_EZX
+config ARCH_PXA_ESERIES
+ bool "PXA based Toshiba e-series PDAs"
+ select PXA25x
+ select PXA_HAVE_BOARD_IRQS
-config MACH_EZX_E680
- bool "Motorola EZX E680"
+config MACH_E330
+ bool "Toshiba e330"
default y
- depends on PXA_EZX
+ depends on ARCH_PXA_ESERIES
+ help
+ Say Y here if you intend to run this kernel on a Toshiba
+ e330 family PDA.
-config MACH_EZX_A1200
- bool "Motorola EZX A1200"
+config MACH_E350
+ bool "Toshiba e350"
default y
- depends on PXA_EZX
+ depends on ARCH_PXA_ESERIES
+ help
+ Say Y here if you intend to run this kernel on a Toshiba
+ e350 family PDA.
-config MACH_EZX_A910
- bool "Motorola EZX A910"
+config MACH_E740
+ bool "Toshiba e740"
default y
- depends on PXA_EZX
+ depends on ARCH_PXA_ESERIES
+ select FB_W100
+ help
+ Say Y here if you intend to run this kernel on a Toshiba
+ e740 family PDA.
-config MACH_EZX_E6
- bool "Motorola EZX E6"
+config MACH_E750
+ bool "Toshiba e750"
default y
- depends on PXA_EZX
+ depends on ARCH_PXA_ESERIES
+ select FB_W100
+ help
+ Say Y here if you intend to run this kernel on a Toshiba
+ e750 family PDA.
-config MACH_EZX_E2
- bool "Motorola EZX E2"
+config MACH_E400
+ bool "Toshiba e400"
default y
- depends on PXA_EZX
+ depends on ARCH_PXA_ESERIES
+ help
+ Say Y here if you intend to run this kernel on a Toshiba
+ e400 family PDA.
-config MACH_XCEP
- bool "Iskratel Electronics XCEP"
- select PXA25x
- select MTD
- select MTD_PARTITIONS
- select MTD_PHYSMAP
- select MTD_CFI_INTELEXT
- select MTD_CFI
- select MTD_CHAR
- select SMC91X
- select PXA_SSP
+config MACH_E800
+ bool "Toshiba e800"
+ default y
+ depends on ARCH_PXA_ESERIES
+ select FB_W100
help
- PXA255 based Single Board Computer with SMC 91C111 ethernet chip and 64 MB of flash.
- Tuned for usage in Libera instruments for particle accelerators.
+ Say Y here if you intend to run this kernel on a Toshiba
+ e800 family PDA.
endmenu
diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile
index e5d450c..cdaf888 100644
--- a/arch/arm/mach-pxa/Makefile
+++ b/arch/arm/mach-pxa/Makefile
@@ -24,33 +24,66 @@ obj-$(CONFIG_CPU_PXA300) += pxa300.o
obj-$(CONFIG_CPU_PXA320) += pxa320.o
obj-$(CONFIG_CPU_PXA930) += pxa930.o
-# Specific board support
-obj-$(CONFIG_ARCH_GUMSTIX) += gumstix.o
-obj-$(CONFIG_GUMSTIX_AM200EPD) += am200epd.o
-obj-$(CONFIG_GUMSTIX_AM300EPD) += am300epd.o
+# NOTE: keep the order of boards in accordance to their order in Kconfig
+
+# Intel/Marvell Dev Platforms
obj-$(CONFIG_ARCH_LUBBOCK) += lubbock.o
-obj-$(CONFIG_MACH_LOGICPD_PXA270) += lpd270.o
obj-$(CONFIG_MACH_MAINSTONE) += mainstone.o
-obj-$(CONFIG_MACH_BALLOON3) += balloon3.o
-obj-$(CONFIG_MACH_MP900C) += mp900.o
+ifeq ($(CONFIG_MACH_ZYLONITE),y)
+ obj-y += zylonite.o
+ obj-$(CONFIG_CPU_PXA300) += zylonite_pxa300.o
+ obj-$(CONFIG_CPU_PXA320) += zylonite_pxa320.o
+endif
+obj-$(CONFIG_MACH_LITTLETON) += littleton.o
+obj-$(CONFIG_MACH_TAVOREVB) += tavorevb.o
+obj-$(CONFIG_MACH_SAAR) += saar.o
+
+# 3rd Party Dev Platforms
obj-$(CONFIG_ARCH_PXA_IDP) += idp.o
+obj-$(CONFIG_ARCH_VIPER) += viper.o
+obj-$(CONFIG_MACH_BALLOON3) += balloon3.o
+obj-$(CONFIG_MACH_CSB726) += csb726.o
+obj-$(CONFIG_CSB726_CSB701) += csb701.o
+obj-$(CONFIG_MACH_ARMCORE) += cm-x2xx.o cm-x255.o cm-x270.o
+ifeq ($(CONFIG_PCI),y)
+obj-$(CONFIG_MACH_ARMCORE) += cm-x2xx-pci.o
+endif
+obj-$(CONFIG_MACH_EM_X270) += em-x270.o
+obj-$(CONFIG_MACH_CM_X300) += cm-x300.o
+obj-$(CONFIG_ARCH_GUMSTIX) += gumstix.o
+obj-$(CONFIG_GUMSTIX_AM200EPD) += am200epd.o
+obj-$(CONFIG_GUMSTIX_AM300EPD) += am300epd.o
+obj-$(CONFIG_MACH_INTELMOTE2) += imote2.o
+obj-$(CONFIG_MACH_STARGATE2) += stargate2.o
+obj-$(CONFIG_MACH_XCEP) += xcep.o
obj-$(CONFIG_MACH_TRIZEPS4) += trizeps4.o
+obj-$(CONFIG_MACH_LOGICPD_PXA270) += lpd270.o
+obj-$(CONFIG_MACH_PCM027) += pcm027.o
+obj-$(CONFIG_MACH_PCM990_BASEBOARD) += pcm990-baseboard.o
obj-$(CONFIG_MACH_COLIBRI) += colibri-pxa270.o
obj-$(CONFIG_MACH_COLIBRI300) += colibri-pxa3xx.o colibri-pxa300.o
obj-$(CONFIG_MACH_COLIBRI320) += colibri-pxa3xx.o colibri-pxa320.o
+
+# End-user Products
+obj-$(CONFIG_MACH_H4700) += hx4700.o
obj-$(CONFIG_MACH_H5000) += h5000.o
+obj-$(CONFIG_MACH_HIMALAYA) += himalaya.o
+obj-$(CONFIG_MACH_MAGICIAN) += magician.o
+obj-$(CONFIG_MACH_MIOA701) += mioa701.o mioa701_bootresume.o
+obj-$(CONFIG_PXA_EZX) += ezx.o
+obj-$(CONFIG_MACH_MP900C) += mp900.o
+obj-$(CONFIG_MACH_PALMTE2) += palmte2.o
+obj-$(CONFIG_MACH_PALMTC) += palmtc.o
+obj-$(CONFIG_MACH_PALMT5) += palmt5.o
+obj-$(CONFIG_MACH_PALMTX) += palmtx.o
+obj-$(CONFIG_MACH_PALMZ72) += palmz72.o
+obj-$(CONFIG_MACH_PALMLD) += palmld.o
+obj-$(CONFIG_PALM_TREO) += palmtreo.o
obj-$(CONFIG_PXA_SHARP_C7xx) += corgi.o sharpsl_pm.o corgi_pm.o
obj-$(CONFIG_PXA_SHARP_Cxx00) += spitz.o sharpsl_pm.o spitz_pm.o
obj-$(CONFIG_CORGI_SSP_DEPRECATED) += corgi_ssp.o corgi_lcd.o
obj-$(CONFIG_MACH_POODLE) += poodle.o
-obj-$(CONFIG_MACH_PCM027) += pcm027.o
-obj-$(CONFIG_MACH_PCM990_BASEBOARD) += pcm990-baseboard.o
obj-$(CONFIG_MACH_TOSA) += tosa.o
-obj-$(CONFIG_MACH_EM_X270) += em-x270.o
-obj-$(CONFIG_MACH_H4700) += hx4700.o
-obj-$(CONFIG_MACH_MAGICIAN) += magician.o
-obj-$(CONFIG_MACH_HIMALAYA) += himalaya.o
-obj-$(CONFIG_MACH_MIOA701) += mioa701.o mioa701_bootresume.o
obj-$(CONFIG_ARCH_PXA_ESERIES) += eseries.o
obj-$(CONFIG_MACH_E330) += e330.o
obj-$(CONFIG_MACH_E350) += e350.o
@@ -58,34 +91,6 @@ obj-$(CONFIG_MACH_E740) += e740.o
obj-$(CONFIG_MACH_E750) += e750.o
obj-$(CONFIG_MACH_E400) += e400.o
obj-$(CONFIG_MACH_E800) += e800.o
-obj-$(CONFIG_MACH_PALMTE2) += palmte2.o
-obj-$(CONFIG_MACH_PALMTC) += palmtc.o
-obj-$(CONFIG_MACH_PALMT5) += palmt5.o
-obj-$(CONFIG_MACH_PALMTX) += palmtx.o
-obj-$(CONFIG_MACH_PALMLD) += palmld.o
-obj-$(CONFIG_MACH_PALMZ72) += palmz72.o
-obj-$(CONFIG_PALM_TREO) += palmtreo.o
-obj-$(CONFIG_ARCH_VIPER) += viper.o
-
-ifeq ($(CONFIG_MACH_ZYLONITE),y)
- obj-y += zylonite.o
- obj-$(CONFIG_CPU_PXA300) += zylonite_pxa300.o
- obj-$(CONFIG_CPU_PXA320) += zylonite_pxa320.o
-endif
-obj-$(CONFIG_MACH_LITTLETON) += littleton.o
-obj-$(CONFIG_MACH_TAVOREVB) += tavorevb.o
-obj-$(CONFIG_MACH_SAAR) += saar.o
-
-obj-$(CONFIG_MACH_ARMCORE) += cm-x2xx.o cm-x255.o cm-x270.o
-obj-$(CONFIG_MACH_CM_X300) += cm-x300.o
-obj-$(CONFIG_PXA_EZX) += ezx.o
-
-obj-$(CONFIG_MACH_XCEP) += xcep.o
-
-obj-$(CONFIG_MACH_INTELMOTE2) += imote2.o
-obj-$(CONFIG_MACH_STARGATE2) += stargate2.o
-obj-$(CONFIG_MACH_CSB726) += csb726.o
-obj-$(CONFIG_CSB726_CSB701) += csb701.o
# Support for blinky lights
led-y := leds.o
@@ -95,8 +100,4 @@ led-$(CONFIG_ARCH_PXA_IDP) += leds-idp.o
obj-$(CONFIG_LEDS) += $(led-y)
-ifeq ($(CONFIG_PCI),y)
-obj-$(CONFIG_MACH_ARMCORE) += cm-x2xx-pci.o
-endif
-
obj-$(CONFIG_TOSA_BT) += tosa-bt.o
More information about the linux-arm-kernel
mailing list