[PATCH 5/6] pcm038: Add SPI/MC13783 support

[Sascha Hauer]

Signed-off-by: Sascha Hauer <s.hauer at pengutronix.de>
---
 arch/arm/mach-mx2/pcm038.c |   92 +++++++++++++++++++++++++++++++++++++++++++-
 1 files changed, 90 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-mx2/pcm038.c b/arch/arm/mach-mx2/pcm038.c
index ee65dda..2262e18 100644
--- a/arch/arm/mach-mx2/pcm038.c
+++ b/arch/arm/mach-mx2/pcm038.c
@@ -23,6 +23,10 @@
 #include <linux/mtd/plat-ram.h>
 #include <linux/mtd/physmap.h>
 #include <linux/platform_device.h>
+#include <linux/regulator/machine.h>
+#include <linux/mfd/mc13783.h>
+#include <linux/spi/spi.h>
+#include <linux/irq.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -35,6 +39,7 @@
 #include <mach/iomux.h>
 #include <mach/imx-uart.h>
 #include <mach/mxc_nand.h>
+#include <mach/spi.h>
 
 #include "devices.h"
 
@@ -78,8 +83,6 @@ static int pcm038_pins[] = {
 	PC6_PF_I2C2_SCL,
 	/* SPI1 */
 	PD25_PF_CSPI1_RDY,
-	PD27_PF_CSPI1_SS1,
-	PD28_PF_CSPI1_SS0,
 	PD29_PF_CSPI1_SCLK,
 	PD30_PF_CSPI1_MISO,
 	PD31_PF_CSPI1_MOSI,
@@ -196,6 +199,86 @@ static struct i2c_board_info pcm038_i2c_devices[] = {
 	}
 };
 
+static int pcm038_spi_cs[] = {GPIO_PORTD + 28};
+
+static struct spi_imx_master pcm038_spi_0_data = {
+	.chipselect = pcm038_spi_cs,
+	.num_chipselect = ARRAY_SIZE(pcm038_spi_cs),
+};
+
+static struct regulator_consumer_supply sdhc1_consumers[] = {
+	{
+		.dev	= &mxc_sdhc_device1.dev,
+		.supply	= "sdhc_vcc",
+	},
+};
+
+static struct regulator_init_data sdhc1_data = {
+	.constraints = {
+		.min_uV = 3000000,
+		.max_uV = 3400000,
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+			REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL |
+			REGULATOR_MODE_FAST,
+		.always_on = 0,
+		.boot_on = 0,
+	},
+	.num_consumer_supplies = ARRAY_SIZE(sdhc1_consumers),
+	.consumer_supplies = sdhc1_consumers,
+};
+
+static struct regulator_consumer_supply cam_consumers[] = {
+	{
+		.dev	= NULL,
+		.supply	= "imx_cam_vcc",
+	},
+};
+
+static struct regulator_init_data cam_data = {
+	.constraints = {
+		.min_uV = 3000000,
+		.max_uV = 3400000,
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
+			REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
+		.valid_modes_mask = REGULATOR_MODE_NORMAL |
+			REGULATOR_MODE_FAST,
+		.always_on = 0,
+		.boot_on = 0,
+	},
+	.num_consumer_supplies = ARRAY_SIZE(cam_consumers),
+	.consumer_supplies = cam_consumers,
+};
+
+struct mc13783_regulator_init_data pcm038_regulators[] = {
+	{
+		.id = MC13783_REGU_VCAM,
+		.init_data = &cam_data,
+	}, {
+		.id = MC13783_REGU_VMMC1,
+		.init_data = &sdhc1_data,
+	},
+};
+
+static struct mc13783_platform_data pcm038_pmic = {
+	.regulators = pcm038_regulators,
+	.num_regulators = ARRAY_SIZE(pcm038_regulators),
+	.flags = MC13783_USE_ADC | MC13783_USE_REGULATOR |
+		 MC13783_USE_TOUCHSCREEN,
+};
+
+static struct spi_board_info pcm038_spi_board_info[] __initdata = {
+	{
+		.modalias = "mc13783",
+		.irq = IRQ_GPIOB(23),
+		.max_speed_hz = 300000,
+		.bus_num = 0,
+		.chip_select = 0,
+		.platform_data = &pcm038_pmic,
+		.mode = SPI_CS_HIGH,
+	}
+};
+
 static void __init pcm038_init(void)
 {
 	mxc_gpio_setup_multiple_pins(pcm038_pins, ARRAY_SIZE(pcm038_pins),
@@ -219,6 +302,11 @@ static void __init pcm038_init(void)
 	/* PE18 for user-LED D40 */
 	mxc_gpio_mode(GPIO_PORTE | 18 | GPIO_GPIO | GPIO_OUT);
 
+	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
+	mxc_register_device(&mxc_spi_device0, &pcm038_spi_0_data);
+	spi_register_board_info(pcm038_spi_board_info,
+				ARRAY_SIZE(pcm038_spi_board_info));
+
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
 
 #ifdef CONFIG_MACH_PCM970_BASEBOARD
-- 
1.6.4.3