[PATCH 1/4] i2c: imx: check busy bit when START/STOP

Richard Zhao linuxzsc at gmail.com
Thu Oct 1 04:03:20 EDT 2009


On Thu, Oct 1, 2009 at 9:13 AM, Richard Zhao <linuxzsc at gmail.com> wrote:
> After START/RESTART, wait for busy bit to be set and
> after STOP, wait for busy bit to be clear.
>
> Signed-off-by: Richard Zhao <linuxzsc at gmail.com>
>
> diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
> index 4afba3e..156cc95 100644
> --- a/drivers/i2c/busses/i2c-imx.c
> +++ b/drivers/i2c/busses/i2c-imx.c
> @@ -125,14 +125,19 @@ struct imx_i2c_struct {
>  /** Functions for IMX I2C adapter driver ***************************************
>  *******************************************************************************/
>
> -static int i2c_imx_bus_busy(struct imx_i2c_struct *i2c_imx)
> +static int i2c_imx_bus_busy(struct imx_i2c_struct *i2c_imx, int for_busy)
>  {
>        unsigned long orig_jiffies = jiffies;
> +       unsigned int temp;
>
>        dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
>
> -       /* wait for bus not busy */
> -       while (readb(i2c_imx->base + IMX_I2C_I2SR) & I2SR_IBB) {
> +       temp = readb(i2c_imx->base + IMX_I2C_I2SR);
> +       while (1) {
> +               if (for_busy && (temp & I2SR_IBB))
> +                       break;
> +               if (!for_busy && !(temp & I2SR_IBB))
> +                       break;
>                if (signal_pending(current)) {
>                        dev_dbg(&i2c_imx->adapter.dev,
>                                "<%s> I2C Interrupted\n", __func__);
> @@ -144,6 +149,7 @@ static int i2c_imx_bus_busy(struct imx_i2c_struct *i2c_imx)
>                        return -EIO;
>                }
>                schedule();
> +               temp = readb(i2c_imx->base + IMX_I2C_I2SR);
>        }
>
>        return 0;
> @@ -179,20 +185,32 @@ static int i2c_imx_acked(struct imx_i2c_struct *i2c_imx)
>        return 0;
>  }
>
> -static void i2c_imx_start(struct imx_i2c_struct *i2c_imx)
> +static int i2c_imx_start(struct imx_i2c_struct *i2c_imx)
>  {
>        unsigned int temp = 0;
> +       int result;
>
>        dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
>
>        /* Enable I2C controller */
> +       writeb(0, i2c_imx->base + IMX_I2C_I2SR);
>        writeb(I2CR_IEN, i2c_imx->base + IMX_I2C_I2CR);
> +
> +       result = i2c_imx_bus_busy(i2c_imx, 0);
> +       if (result)
> +               return result;
> +
>        /* Start I2C transaction */
>        temp = readb(i2c_imx->base + IMX_I2C_I2CR);
>        temp |= I2CR_MSTA;
>        writeb(temp, i2c_imx->base + IMX_I2C_I2CR);
> +       result = i2c_imx_bus_busy(i2c_imx, 1);
> +       if (result)
> +               return result;
> +
>        temp |= I2CR_IIEN | I2CR_MTX | I2CR_TXAK;
>        writeb(temp, i2c_imx->base + IMX_I2C_I2CR);
> +       return result;
>  }
>
>  static void i2c_imx_stop(struct imx_i2c_struct *i2c_imx)
> @@ -202,16 +220,16 @@ static void i2c_imx_stop(struct imx_i2c_struct *i2c_imx)
>        /* Stop I2C transaction */
>        dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
>        temp = readb(i2c_imx->base + IMX_I2C_I2CR);
> -       temp &= ~I2CR_MSTA;
> +       temp &= ~(I2CR_MSTA | I2CR_MTX);
>        writeb(temp, i2c_imx->base + IMX_I2C_I2CR);
> -       /* setup chip registers to defaults */
> -       writeb(I2CR_IEN, i2c_imx->base + IMX_I2C_I2CR);
> -       writeb(0, i2c_imx->base + IMX_I2C_I2SR);
>        /*
>         * This delay caused by an i.MXL hardware bug.
>         * If no (or too short) delay, no "STOP" bit will be generated.
>         */
>        udelay(i2c_imx->disable_delay);
> +
> +       i2c_imx_bus_busy(i2c_imx, 0);
> +
>        /* Disable I2C controller */
>        writeb(0, i2c_imx->base + IMX_I2C_I2CR);
>  }
> @@ -344,7 +362,7 @@ static int i2c_imx_read(struct imx_i2c_struct *i2c_imx, struct i2c_msg *msgs)
>                        dev_dbg(&i2c_imx->adapter.dev,
>                                "<%s> clear MSTA\n", __func__);
>                        temp = readb(i2c_imx->base + IMX_I2C_I2CR);
> -                       temp &= ~I2CR_MSTA;
> +                       temp &= ~(I2CR_MSTA | I2CR_MTX);
>                        writeb(temp, i2c_imx->base + IMX_I2C_I2CR);
>                } else if (i == (msgs->len - 2)) {
>                        dev_dbg(&i2c_imx->adapter.dev,
> @@ -370,14 +388,11 @@ static int i2c_imx_xfer(struct i2c_adapter *adapter,
>
>        dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
>
> -       /* Check if i2c bus is not busy */
> -       result = i2c_imx_bus_busy(i2c_imx);
> +       /* Start I2C transfer */
> +       result = i2c_imx_start(i2c_imx);
>        if (result)
>                goto fail0;
>
> -       /* Start I2C transfer */
> -       i2c_imx_start(i2c_imx);
> -
>        /* read/write data */
>        for (i = 0; i < num; i++) {
>                if (i) {
> @@ -386,6 +401,9 @@ static int i2c_imx_xfer(struct i2c_adapter *adapter,
>                        temp = readb(i2c_imx->base + IMX_I2C_I2CR);
>                        temp |= I2CR_RSTA;
>                        writeb(temp, i2c_imx->base + IMX_I2C_I2CR);
> +                       result =  i2c_imx_bus_busy(i2c_imx, 1);
> +                       if (result)
> +                               goto fail0;
>                }
>                dev_dbg(&i2c_imx->adapter.dev,
>                        "<%s> transfer message: %d\n", __func__, i);
> --
> 1.6.0.4
>
>

Hi Sascha,

So I assume you have no comments about this patch ?

Thanks
Richard



More information about the linux-arm-kernel mailing list