RFC [PATCH 5/9] Added phy3250 platform for the lcp3250
Kevin Wells
kevin.wells at nxp.com
Fri Nov 20 13:15:57 EST 2009
Hi Wan,
I'm still a bit new to how this works, but I'll run future patches
through this script prior to posting them.
thanks,
Kevin Wells
NXP Semiconductors
> -----Original Message-----
> From: Wan ZongShun [mailto:mcuos.com at gmail.com]
> Sent: Thursday, November 19, 2009 9:33 PM
> To: Kevin Wells
> Cc: linux-arm-kernel at lists.infradead.org
> Subject: Re: RFC [PATCH 5/9] Added phy3250 platform for the lcp3250
>
> Dear Kevin Wells ,
>
> Could you use the checkpatch.pl to fix your current patch?
> I see the following info:
>
> WARNING: space prohibited between function name and open parenthesis '('
> #616: FILE: arch/arm/mach-lpc32xx/phy3250.c:528:
> + .io_pg_offst = ((io_p2v (UART5_BASE))>>18) & 0xfffc,
>
> total: 123 errors, 21 warnings, 534 lines checked
>
>
>
> thanks!
>
>
> > Added phy3250 platform for the lcp3250
> >
> > Signed-off-by: Kevin Wells <kevin.wells at nxp.com>
> > ---
> > arch/arm/mach-lpc32xx/phy3250.c | 534
> +++++++++++++++++++++++++++++++++++++++
> > 1 files changed, 534 insertions(+), 0 deletions(-)
> > create mode 100644 arch/arm/mach-lpc32xx/phy3250.c
> >
> > diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-
> lpc32xx/phy3250.c
> > new file mode 100644
> > index 0000000..844c344
> > --- /dev/null
> > +++ b/arch/arm/mach-lpc32xx/phy3250.c
> > @@ -0,0 +1,534 @@
> > +/*
> > + * linux/arch/arm/mach-lpc32xx/phy3250.c
> > + *
> > + * Copyright (C) 2009 NXP Semiconductors
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * You should have received a copy of the GNU General Public License
> > + * along with this program; if not, write to the Free Software
> > + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307
> USA
> > + */
> > +
> > +#include <linux/tty.h>
> > +#include <linux/init.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/sysdev.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/irq.h>
> > +#include <linux/dma-mapping.h>
> > +#include <linux/sysdev.h>
> > +#include <linux/input.h>
> > +#include <linux/device.h>
> > +#include <linux/spi/spi.h>
> > +#include <linux/spi/eeprom.h>
> > +#include <linux/delay.h>
> > +#include <linux/leds.h>
> > +#include <linux/gpio.h>
> > +#include <linux/mmc/host.h>
> > +#include <linux/amba/bus.h>
> > +#include <linux/amba/clcd.h>
> > +#include <linux/amba/mmci.h>
> > +#include <linux/amba/pl022.h>
> > +
> > +#include <mach/hardware.h>
> > +#include <asm/setup.h>
> > +#include <asm/mach-types.h>
> > +#include <asm/mach/arch.h>
> > +#include <asm/irq.h>
> > +#include <asm/mach/irq.h>
> > +#include <asm/mach/map.h>
> > +
> > +#include <mach/platform.h>
> > +#include <mach/clock.h>
> > +#include <mach/gpio.h>
> > +#include "common.h"
> > +
> > +/*
> > + * Mapped GPIOLIB GPIOs
> > + */
> > +#define SPI0_CS_GPIO LPC32XX_GPIO(GPIO_P3_GRP, 5)
> > +#define LCD_POWER_GPIO LPC32XX_GPIO(GPO_P3_GRP, 0)
> > +#define BKL_POWER_GPIO LPC32XX_GPIO(GPO_P3_GRP, 4)
> > +#define LED_GPIO LPC32XX_GPIO(GPO_P3_GRP, 1)
> > +
> > +static void phy3250_spi_cs_set(u32 control);
> > +
> > +
> > +#define PHY_HW_VER_VAL 0x000A3250
> > +#define SEEPROM_READ 0x03
> > +#define PHY3250_SEEPROM_SIZE 0x8000
> > +#define PHY3250_SEEPROM_CFGOFS (PHY3250_SEEPROM_SIZE - 0x100)
> > +
> > +/*
> > + * Structure used to define the hardware for the Phytec board
> > + */
> > +struct phytec_hardware {
> > + u32 dramcfg;
> > + u32 syscfg;
> > + u8 mac[8]; /* Only the first 6 are used */
> > + u32 rsvd [5];
> > + u32 fieldvval;
> > +} PHY_HW_T;
> > +static struct phytec_hardware phyhwdata;
> > +
> > +/*
> > + * Load board hardware descriptor to get MAC address
> > + */
> > +static void __init phy3250_load_hw_desc(void)
> > +{
> > + u32 tmp, addr, saveclk;
> > + int i, len;
> > + u8 *p8, cmd [4], in [4];
> > + u32 sspiobase = io_p2v(SSP0_BASE);
> > +
> > + saveclk = readl(CLKPWR_SSP_CLK_CTRL(CLKPWR_IOBASE));
> > + writel((saveclk | CLKPWR_SSPCTRL_SSPCLK0_EN),
> > + CLKPWR_SSP_CLK_CTRL(CLKPWR_IOBASE));
> > +
> > + writel(0, LSSP_ICR(sspiobase));
> > + writel((LSSP_ICR_RORIC | LSSP_ICR_RTIC), LSSP_IMSC(sspiobase));
> > +
> > + /* Setup default SPI mode at about 5MHz */
> > + writel((LSSP_CR0_DSS(8) | LSSP_CR0_FRF_SPI | LSSP_CR0_CPOL(0) |
> > + LSSP_CR0_CPHA(0) | LSSP_CR0_SCR(40)),
> LSSP_CR0(sspiobase));
> > + writel(LSSP_CR1_SSP_ENABLE, LSSP_CR1(sspiobase));
> > + writel(LSSP_CPSR_CPDVSR(40), LSSP_CPSR(sspiobase));
> > +
> > + while (readl(LSSP_SR(sspiobase)) & LSSP_SR_RNE)
> > + tmp = readl(LSSP_DATA(sspiobase));
> > +
> > + len = sizeof (phyhwdata);
> > + p8 = (u8 *) &phyhwdata;
> > + addr = PHY3250_SEEPROM_CFGOFS;
> > + while (len > 0) {
> > + phy3250_spi_cs_set(0);
> > +
> > + /* Issue read command and address for 1 byte */
> > + cmd[0] = SEEPROM_READ;
> > + cmd[1] = ((addr >> 8) & 0xFF);
> > + cmd[2] = ((addr >> 0) & 0xFF);
> > + cmd[3] = 0xFF;
> > + for (i = 0; i < 4; i++)
> > + writel((u32) cmd [i], LSSP_DATA(sspiobase));
> > +
> > + /* Save 3 null bytes and 1 data byte */
> > + i = 0;
> > + while (i < 4) {
> > + if (readl(LSSP_SR(sspiobase)) & LSSP_SR_RNE) {
> > + in[i] = (u8) readl(LSSP_DATA(sspiobase));
> > + i++;
> > + }
> > + }
> > +
> > + /* Only that last byte matters */
> > + *p8 = in [3];
> > + p8++;
> > + len--;
> > + addr++;
> > +
> > + phy3250_spi_cs_set(1);
> > + }
> > +
> > + writel(0, LSSP_CR0(sspiobase));
> > +
> > + if (phyhwdata.fieldvval != PHY_HW_VER_VAL)
> > + printk(KERN_ERR "Invalid Phytec board descriptor!\n");
> > +
> > + /* Shutdown SSP clock to save power */
> > + writel((saveclk & ~CLKPWR_SSPCTRL_SSPCLK0_EN),
> > + CLKPWR_SSP_CLK_CTRL(CLKPWR_IOBASE));
> > +}
> > +
> > +/*
> > + * AMBA LCD controller
> > + */
> > +static struct clcd_panel conn_lcd_panel = {
> > + .mode = {
> > + .name = "QVGA portrait",
> > + .refresh = 60,
> > + .xres = 240,
> > + .yres = 320,
> > + .pixclock = 191828,
> > + .left_margin = 22,
> > + .right_margin = 11,
> > + .upper_margin = 2,
> > + .lower_margin = 1,
> > + .hsync_len = 5,
> > + .vsync_len = 2,
> > + .sync = 0,
> > + .vmode = FB_VMODE_NONINTERLACED,
> > + },
> > + .width = -1,
> > + .height = -1,
> > + .tim2 = (TIM2_IVS | TIM2_IHS),
> > + .cntl = (CNTL_BGR | CNTL_LCDTFT | CNTL_LCDVCOMP(1) |
> > + CNTL_LCDBPP16_565),
> > + .bpp = 16,
> > +};
> > +#define PANEL_SIZE (3 * SZ_64K)
> > +
> > +static int lpc32xx_clcd_setup(struct clcd_fb *fb)
> > +{
> > + dma_addr_t dma;
> > +
> > + fb->fb.screen_base = (void *) NULL;
> > +#if defined(CONFIG_MACH_LPC32XX_IRAM_FOR_CLCD)
> > + if (PANEL_SIZE <= LPC32XX_IRAM_SIZE) {
> > + fb->fb.screen_base = (void *) io_p2v(IRAM_BASE);
> > + fb->fb.fix.smem_start = (dma_addr_t) IRAM_BASE;
> > + }
> > +#endif
> > +
> > + if (fb->fb.screen_base == NULL) {
> > + fb->fb.screen_base = dma_alloc_writecombine(&fb->dev-
> >dev,
> > + PANEL_SIZE, &dma, GFP_KERNEL);
> > + fb->fb.fix.smem_start = dma;
> > + }
> > +
> > + if (!fb->fb.screen_base) {
> > + printk(KERN_ERR "CLCD: unable to map framebuffer\n");
> > + return -ENOMEM;
> > + }
> > +
> > + fb->fb.fix.smem_len = PANEL_SIZE;
> > + fb->panel = &conn_lcd_panel;
> > +
> > + gpio_request(LCD_POWER_GPIO, "LCD power");
> > + gpio_direction_output(LCD_POWER_GPIO, 1);
> > + gpio_request(BKL_POWER_GPIO, "LCD backlight power");
> > + gpio_direction_output(BKL_POWER_GPIO, 1);
> > +
> > + return 0;
> > +}
> > +
> > +static int lpc32xx_clcd_mmap(struct clcd_fb *fb, struct vm_area_struct
> *vma)
> > +{
> > +#if defined(CONFIG_MACH_LPC32XX_IRAM_FOR_CLCD)
> > + if (PANEL_SIZE <= LPC32XX_IRAM_SIZE) {
> > + vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
> > + if (remap_pfn_range(vma, vma->vm_start, vma->vm_pgoff,
> > + (vma->vm_end - vma->vm_start), vma-
> >vm_page_prot)) {
> > + return -EAGAIN;
> > + }
> > +
> > + return 0;
> > + }
> > + else
> > +#endif
> > +
> > + return dma_mmap_writecombine(&fb->dev->dev, vma,
> > + fb->fb.screen_base,
> > + fb->fb.fix.smem_start,
> > + fb->fb.fix.smem_len);
> > +}
> > +
> > +static void lpc32xx_clcd_remove(struct clcd_fb *fb)
> > +{
> > +#if defined(CONFIG_MACH_LPC32XX_IRAM_FOR_CLCD)
> > + if (PANEL_SIZE > LPC32XX_IRAM_SIZE)
> > +#endif
> > +
> > + dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len,
> > + fb->fb.screen_base, fb->fb.fix.smem_start);
> > +}
> > +
> > +#if defined (CONFIG_PHY3250_QVGA_PANEL_1307_0)
> > +#define LCD_BKL_ON 0
> > +#define LCD_BKL_OFF 1
> > +#elif defined (CONFIG_PHY3250_QVGA_PANEL_1307_1)
> > +#define LCD_BKL_ON 1
> > +#define LCD_BKL_OFF 0
> > +#endif
> > +
> > +static void clcd_disable(struct clcd_fb *fb)
> > +{
> > + gpio_set_value(BKL_POWER_GPIO, LCD_BKL_OFF);
> > + gpio_set_value(LCD_POWER_GPIO, 0);
> > +}
> > +
> > +static void clcd_enable(struct clcd_fb *fb)
> > +{
> > + gpio_set_value(BKL_POWER_GPIO, LCD_BKL_ON);
> > + gpio_set_value(LCD_POWER_GPIO, 1);
> > +}
> > +
> > +static struct clcd_board lpc32xx_clcd_data = {
> > + .name = "Phytec LCD",
> > + .check = clcdfb_check,
> > + .decode = clcdfb_decode,
> > + .disable = clcd_disable,
> > + .enable = clcd_enable,
> > + .setup = lpc32xx_clcd_setup,
> > + .mmap = lpc32xx_clcd_mmap,
> > + .remove = lpc32xx_clcd_remove,
> > +};
> > +
> > +static struct amba_device clcd_device = {
> > + .dev = {
> > + .coherent_dma_mask = ~0,
> > + .init_name = "dev:clcd",
> > + .platform_data = &lpc32xx_clcd_data,
> > + },
> > + .res = {
> > + .start = LCD_BASE,
> > + .end = (LCD_BASE + SZ_4K - 1),
> > + .flags = IORESOURCE_MEM,
> > + },
> > + .dma_mask = ~0,
> > + .irq = {IRQ_LCD, NO_IRQ},
> > +};
> > +
> > +/*
> > + * AMBA SSP (SPI)
> > + */
> > +static void phy3250_spi_cs_set(u32 control)
> > +{
> > + gpio_set_value(SPI0_CS_GPIO, (int) control);
> > +}
> > +
> > +static struct pl022_config_chip spi0_chip_info = {
> > + .lbm = LOOPBACK_DISABLED,
> > + .com_mode = POLLING_TRANSFER,
> > + .iface = SSP_INTERFACE_MOTOROLA_SPI,
> > + .hierarchy = SSP_SLAVE,
> > + .slave_tx_disable = 0,
> > + .endian_tx = SSP_TX_LSB,
> > + .endian_rx = SSP_RX_LSB,
> > + .data_size = SSP_DATA_BITS_8,
> > + .rx_lev_trig = SSP_RX_8_OR_MORE_ELEM,
> > + .tx_lev_trig = SSP_TX_8_OR_MORE_EMPTY_LOC,
> > + .clk_phase = SSP_CLK_SECOND_EDGE,
> > + .clk_pol = SSP_CLK_POL_IDLE_LOW,
> > + .ctrl_len = SSP_BITS_8,
> > + .wait_state = SSP_MWIRE_WAIT_ZERO,
> > + .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
> > + .cs_control = phy3250_spi_cs_set,
> > +};
> > +
> > +static struct pl022_ssp_controller lpc32xx_ssp0_data = {
> > + .bus_id = 0,
> > + .num_chipselect = 1,
> > + .enable_dma = 0
> > +};
> > +
> > +static struct amba_device ssp0_device = {
> > + .dev = {
> > + .coherent_dma_mask = ~0,
> > + .init_name = "dev:ssp0",
> > + .platform_data = &lpc32xx_ssp0_data,
> > + },
> > + .res = {
> > + .start = SSP0_BASE,
> > + .end = (SSP0_BASE + SZ_4K - 1),
> > + .flags = IORESOURCE_MEM,
> > + },
> > + .dma_mask = ~0,
> > + .irq = {IRQ_SSP0, NO_IRQ},
> > +};
> > +
> > +/* AT25 driver registration */
> > +static int __init phy3250_spi_board_register(void)
> > +{
> > +#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
> > + struct spi_board_info info[] = {
> > + {
> > + .modalias = "spidev",
> > + .max_speed_hz = 5000000,
> > + .bus_num = 0,
> > + .chip_select = 0,
> > + .controller_data = &spi0_chip_info,
> > + },
> > + };
> > +
> > +#else
> > + static struct spi_eeprom eeprom = {
> > + .name = "at25256a",
> > + .byte_len = 0x8000,
> > + .page_size = 64,
> > + .flags = EE_ADDR2,
> > + };
> > + struct spi_board_info info[] = {
> > + {
> > + .modalias = "at25",
> > + .max_speed_hz = 5000000,
> > + .bus_num = 0,
> > + .chip_select = 0,
> > + .platform_data = &eeprom,
> > + .controller_data = &spi0_chip_info,
> > + },
> > + };
> > +#endif
> > + return spi_register_board_info(info, ARRAY_SIZE(info));
> > +}
> > +arch_initcall(phy3250_spi_board_register);
> > +
> > +/*
> > + * USB OHCI
> > + */
> > +static u64 ohci_dmamask = ~(u32) 0;
> > +static struct resource ohci_resources[] = {
> > + {
> > + .start = IO_ADDRESS(USB_BASE),
> > + .end = IO_ADDRESS(USB_BASE + 0x100),
> > + .flags = IORESOURCE_MEM,
> > + }, {
> > + .start = IRQ_USB_HOST,
> > + .flags = IORESOURCE_IRQ,
> > + },
> > +};
> > +
> > +struct platform_device ohci_device = {
> > + .name = "usb-ohci",
> > + .id = -1,
> > + .dev = {
> > + .dma_mask = &ohci_dmamask,
> > + .coherent_dma_mask = 0xFFFFFFFF,
> > + },
> > + .num_resources = ARRAY_SIZE(ohci_resources),
> > + .resource = ohci_resources,
> > +};
> > +
> > +static struct i2c_board_info __initdata phy3250_i2c_board_info [] = {
> > + {
> > + I2C_BOARD_INFO("rtc-pcf8563", 0x51),
> > + },
> > +};
> > +
> > +static struct gpio_led phy_leds[] = {
> > + {
> > + .name = "led0",
> > + .gpio = LED_GPIO,
> > + .active_low = 1,
> > + .default_trigger = "heartbeat",
> > + },
> > +};
> > +
> > +static struct gpio_led_platform_data led_data = {
> > + .leds = phy_leds,
> > + .num_leds = ARRAY_SIZE(phy_leds),
> > +};
> > +
> > +static struct platform_device lpc32xx_gpio_led_device = {
> > + .name = "leds-gpio",
> > + .id = -1,
> > + .dev.platform_data = &led_data,
> > +};
> > +
> > +static struct platform_device* phy3250_devs[] __initdata = {
> > + &i2c0_device,
> > + &i2c2_device,
> > + &watchdog_device,
> > + &lpc32xx_gpio_led_device,
> > +};
> > +
> > +static struct amba_device *amba_devs[] __initdata = {
> > + &clcd_device,
> > + &ssp0_device,
> > +};
> > +
> > +/*
> > + * Board specific functions
> > + */
> > +static void __init phy3250_board_init(void)
> > +{
> > + u32 tmp;
> > + int i;
> > +
> > + /* Setup clocks and gpios before anything else! */
> > + clk_init();
> > + lpc32xx_gpio_init();
> > +
> > + /* Register GPIOs used on this board */
> > + gpio_request(SPI0_CS_GPIO, "spi0 cs");
> > + gpio_direction_output(SPI0_CS_GPIO, 1);
> > +
> > + /* Setup network interface for RMII mode */
> > + tmp = readl(CLKPWR_MACCLK_CTRL(CLKPWR_IOBASE));
> > + tmp &= ~CLKPWR_MACCTRL_PINS_MSK;
> > + tmp |= CLKPWR_MACCTRL_USE_RMII_PINS;
> > + writel(tmp, CLKPWR_MACCLK_CTRL(CLKPWR_IOBASE));
> > +
> > + /* Setup SLC NAND controller muxing */
> > + writel(CLKPWR_NANDCLK_SEL_SLC,
> > + CLKPWR_NAND_CLK_CTRL(CLKPWR_IOBASE));
> > +
> > + /* Setup LCD muxing to RGB565 */
> > + tmp = readl(CLKPWR_LCDCLK_CTRL(CLKPWR_IOBASE)) &
> > + ~(CLKPWR_LCDCTRL_LCDTYPE_MSK |
> CLKPWR_LCDCTRL_PSCALE_MSK);
> > + tmp |= CLKPWR_LCDCTRL_LCDTYPE_TFT16;
> > + writel(tmp, CLKPWR_LCDCLK_CTRL(CLKPWR_IOBASE));
> > +
> > + /* Set up I2C levels */
> > + tmp = readl(CLKPWR_I2C_CLK_CTRL(CLKPWR_IOBASE));
> > + tmp |= CLKPWR_I2CCLK_USBI2CHI_DRIVE | CLKPWR_I2CCLK_I2C2HI_DRIVE;
> > + writel(tmp, CLKPWR_I2C_CLK_CTRL(CLKPWR_IOBASE));
> > +
> > + /* Enable DMA for I2S1 channel */
> > + tmp = readl(CLKPWR_I2S_CLK_CTRL(CLKPWR_IOBASE));
> > + tmp = CLKPWR_I2SCTRL_I2S1_USE_DMA;
> > + writel(tmp, CLKPWR_I2S_CLK_CTRL(CLKPWR_IOBASE));
> > +
> > + /* Load the board hardware descriptor, as some other board
> functions
> > + require it's data */
> > + phy3250_load_hw_desc();
> > +
> > + serial_init();
> > +
> > + /* AMBA peripheral clocks need to be enabled prior to AMBA device
> > + detection or a data fault will occur, so we enable the clocks
> > + here. However, we don't want to enable them if the peripheral
> > + isn't included in the image */
> > +#if defined (CONFIG_MMC_ARMMMCI)
> > + tmp = readl(CLKPWR_MS_CTRL(CLKPWR_IOBASE));
> > + writel((tmp | CLKPWR_MSCARD_SDCARD_EN |
> CLKPWR_MSCARD_MSDIO_PU_EN),
> > + CLKPWR_MS_CTRL(CLKPWR_IOBASE));
> > +#endif
> > +#if defined (CONFIG_FB_ARMCLCD)
> > + tmp = readl(CLKPWR_LCDCLK_CTRL(CLKPWR_IOBASE));
> > + writel((tmp | CLKPWR_LCDCTRL_CLK_EN),
> > + CLKPWR_LCDCLK_CTRL(CLKPWR_IOBASE));
> > +#endif
> > +#if defined (CONFIG_SPI_PL022)
> > + tmp = readl(CLKPWR_SSP_CLK_CTRL(CLKPWR_IOBASE));
> > + writel((tmp | CLKPWR_SSPCTRL_SSPCLK0_EN),
> > + CLKPWR_SSP_CLK_CTRL(CLKPWR_IOBASE));
> > +#endif
> > +
> > + platform_add_devices(phy3250_devs, ARRAY_SIZE(phy3250_devs));
> > + for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
> > + struct amba_device *d = amba_devs[i];
> > + amba_device_register(d, &iomem_resource);
> > + }
> > +
> > + /* Disable UART5->USB transparent mode or USB won't work */
> > + tmp = readl(UARTCTL_CTRL(io_p2v(UART_CTRL_BASE)));
> > + tmp &= ~UART_U5_ROUTE_TO_USB;
> > + writel(tmp, UARTCTL_CTRL(io_p2v(UART_CTRL_BASE)));
> > +
> > + /* Test clock needed for UDA1380 initial init */
> > + writel((CLKPWR_TESTCLK2_SEL_MOSC | CLKPWR_TESTCLK_TESTCLK2_EN),
> > + CLKPWR_TEST_CLK_SEL(CLKPWR_IOBASE));
> > +
> > + i2c_register_board_info(0, phy3250_i2c_board_info,
> > + ARRAY_SIZE(phy3250_i2c_board_info));
> > +}
> > +
> > +MACHINE_START (LPC3XXX, "Phytec 3250 board with the LPC3250
> Microcontroller")
> > + /* Maintainer: Kevin Wells, NXP Semiconductors */
> > + .phys_io = UART5_BASE,
> > + .io_pg_offst = ((io_p2v (UART5_BASE))>>18) & 0xfffc,
> > + .boot_params = 0x80000100,
> > + .map_io = lpc32xx_map_io,
> > + .init_irq = lpc32xx_init_irq,
> > + .timer = &lpc32xx_timer,
> > + .init_machine = phy3250_board_init,
> > +MACHINE_END
> > --
> > 1.6.0.6
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel at lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> >
More information about the linux-arm-kernel
mailing list