[PATCH 1/3 v4] Add camera support for A780 and A910 EZX phones
Antonio Ospite
ospite at studenti.unina.it
Thu Nov 12 09:47:04 EST 2009
Signed-off-by: Bart Visscher <bartv at thisnet.nl>
Signed-off-by: Antonio Ospite <ospite at studenti.unina.it>
---
Changes since v3:
- Check {a780,a910}_camera_init() return value, and register camera
conditionally.
arch/arm/mach-pxa/ezx.c | 174 +++++++++++++++++++++++++++++++++++++++++++++-
1 files changed, 170 insertions(+), 4 deletions(-)
diff --git a/arch/arm/mach-pxa/ezx.c b/arch/arm/mach-pxa/ezx.c
index 588b265..46c32cf 100644
--- a/arch/arm/mach-pxa/ezx.c
+++ b/arch/arm/mach-pxa/ezx.c
@@ -17,8 +17,11 @@
#include <linux/delay.h>
#include <linux/pwm_backlight.h>
#include <linux/input.h>
+#include <linux/gpio.h>
#include <linux/gpio_keys.h>
+#include <media/soc_camera.h>
+
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -29,6 +32,7 @@
#include <plat/i2c.h>
#include <mach/hardware.h>
#include <mach/pxa27x_keypad.h>
+#include <mach/camera.h>
#include "devices.h"
#include "generic.h"
@@ -38,6 +42,9 @@
#define GPIO15_A910_FLIP_LID 15
#define GPIO12_E680_LOCK_SWITCH 12
#define GPIO15_E6_LOCK_SWITCH 15
+#define GPIO50_nCAM_EN 50
+#define GPIO19_GEN1_CAM_RST 19
+#define GPIO28_GEN2_CAM_RST 28
static struct platform_pwm_backlight_data ezx_backlight_data = {
.pwm_id = 0,
@@ -191,8 +198,8 @@ static unsigned long gen1_pin_config[] __initdata = {
GPIO94_CIF_DD_5,
GPIO17_CIF_DD_6,
GPIO108_CIF_DD_7,
- GPIO50_GPIO, /* CAM_EN */
- GPIO19_GPIO, /* CAM_RST */
+ GPIO50_GPIO | MFP_LPM_DRIVE_HIGH, /* CAM_EN */
+ GPIO19_GPIO | MFP_LPM_DRIVE_HIGH, /* CAM_RST */
/* EMU */
GPIO120_GPIO, /* EMU_MUX1 */
@@ -248,8 +255,8 @@ static unsigned long gen2_pin_config[] __initdata = {
GPIO48_CIF_DD_5,
GPIO93_CIF_DD_6,
GPIO12_CIF_DD_7,
- GPIO50_GPIO, /* CAM_EN */
- GPIO28_GPIO, /* CAM_RST */
+ GPIO50_GPIO | MFP_LPM_DRIVE_HIGH, /* CAM_EN */
+ GPIO28_GPIO | MFP_LPM_DRIVE_HIGH, /* CAM_RST */
GPIO17_GPIO, /* CAM_FLASH */
};
#endif
@@ -683,6 +690,81 @@ static struct platform_device a780_gpio_keys = {
},
};
+/* camera */
+static int a780_camera_init(void)
+{
+ int err;
+
+ /*
+ * GPIO50_nCAM_EN is active low
+ * GPIO19_GEN1_CAM_RST is active on rising edge
+ */
+ err = gpio_request(GPIO50_nCAM_EN, "nCAM_EN");
+ if (err) {
+ pr_err("%s: Failed to request nCAM_EN\n", __func__);
+ goto fail;
+ }
+
+ err = gpio_request(GPIO19_GEN1_CAM_RST, "CAM_RST");
+ if (err) {
+ pr_err("%s: Failed to request CAM_RST\n", __func__);
+ goto fail_gpio_cam_rst;
+ }
+
+ gpio_direction_output(GPIO50_nCAM_EN, 1);
+ gpio_direction_output(GPIO19_GEN1_CAM_RST, 0);
+
+ return 0;
+
+fail_gpio_cam_rst:
+ gpio_free(GPIO50_nCAM_EN);
+fail:
+ return err;
+}
+
+static int a780_camera_power(struct device *dev, int on)
+{
+ gpio_set_value(GPIO50_nCAM_EN, !on);
+ return 0;
+}
+
+static int a780_camera_reset(struct device *dev)
+{
+ gpio_set_value(GPIO19_GEN1_CAM_RST, 0);
+ msleep(10);
+ gpio_set_value(GPIO19_GEN1_CAM_RST, 1);
+
+ return 0;
+}
+
+struct pxacamera_platform_data a780_pxacamera_platform_data = {
+ .flags = PXA_CAMERA_MASTER | PXA_CAMERA_DATAWIDTH_8 |
+ PXA_CAMERA_PCLK_EN | PXA_CAMERA_MCLK_EN,
+ .mclk_10khz = 5000,
+};
+
+static struct i2c_board_info a780_camera_i2c_board_info = {
+ I2C_BOARD_INFO("mt9m111", 0x5d),
+};
+
+static struct soc_camera_link a780_iclink = {
+ .bus_id = 0,
+ .flags = SOCAM_SENSOR_INVERT_PCLK,
+ .i2c_adapter_id = 0,
+ .board_info = &a780_camera_i2c_board_info,
+ .module_name = "mt9m111",
+ .power = a780_camera_power,
+ .reset = a780_camera_reset,
+};
+
+static struct platform_device a780_camera = {
+ .name = "soc-camera-pdrv",
+ .id = 0,
+ .dev = {
+ .platform_data = &a780_iclink,
+ },
+};
+
static struct platform_device *a780_devices[] __initdata = {
&a780_gpio_keys,
};
@@ -699,6 +781,11 @@ static void __init a780_init(void)
pxa_set_keypad_info(&a780_keypad_platform_data);
+ if (a780_camera_init() == 0) {
+ pxa_set_camera_info(&a780_pxacamera_platform_data);
+ platform_device_register(&a780_camera);
+ }
+
platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
platform_add_devices(ARRAY_AND_SIZE(a780_devices));
}
@@ -864,6 +951,80 @@ static struct platform_device a910_gpio_keys = {
},
};
+/* camera */
+static int a910_camera_init(void)
+{
+ int err;
+
+ /*
+ * GPIO50_nCAM_EN is active low
+ * GPIO28_GEN2_CAM_RST is active on rising edge
+ */
+ err = gpio_request(GPIO50_nCAM_EN, "nCAM_EN");
+ if (err) {
+ pr_err("%s: Failed to request nCAM_EN\n", __func__);
+ goto fail;
+ }
+
+ err = gpio_request(GPIO28_GEN2_CAM_RST, "CAM_RST");
+ if (err) {
+ pr_err("%s: Failed to request CAM_RST\n", __func__);
+ goto fail_gpio_cam_rst;
+ }
+
+ gpio_direction_output(GPIO50_nCAM_EN, 1);
+ gpio_direction_output(GPIO28_GEN2_CAM_RST, 0);
+
+ return 0;
+
+fail_gpio_cam_rst:
+ gpio_free(GPIO50_nCAM_EN);
+fail:
+ return err;
+}
+
+static int a910_camera_power(struct device *dev, int on)
+{
+ gpio_set_value(GPIO50_nCAM_EN, !on);
+ return 0;
+}
+
+static int a910_camera_reset(struct device *dev)
+{
+ gpio_set_value(GPIO28_GEN2_CAM_RST, 0);
+ msleep(10);
+ gpio_set_value(GPIO28_GEN2_CAM_RST, 1);
+
+ return 0;
+}
+
+struct pxacamera_platform_data a910_pxacamera_platform_data = {
+ .flags = PXA_CAMERA_MASTER | PXA_CAMERA_DATAWIDTH_8 |
+ PXA_CAMERA_PCLK_EN | PXA_CAMERA_MCLK_EN,
+ .mclk_10khz = 5000,
+};
+
+static struct i2c_board_info a910_camera_i2c_board_info = {
+ I2C_BOARD_INFO("mt9m111", 0x5d),
+};
+
+static struct soc_camera_link a910_iclink = {
+ .bus_id = 0,
+ .i2c_adapter_id = 0,
+ .board_info = &a910_camera_i2c_board_info,
+ .module_name = "mt9m111",
+ .power = a910_camera_power,
+ .reset = a910_camera_reset,
+};
+
+static struct platform_device a910_camera = {
+ .name = "soc-camera-pdrv",
+ .id = 0,
+ .dev = {
+ .platform_data = &a910_iclink,
+ },
+};
+
static struct platform_device *a910_devices[] __initdata = {
&a910_gpio_keys,
};
@@ -880,6 +1041,11 @@ static void __init a910_init(void)
pxa_set_keypad_info(&a910_keypad_platform_data);
+ if (a910_camera_init() == 0) {
+ pxa_set_camera_info(&a910_pxacamera_platform_data);
+ platform_device_register(&a910_camera);
+ }
+
platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
platform_add_devices(ARRAY_AND_SIZE(a910_devices));
}
--
tg: (639a58f..) ezx/mach/camera_new (depends on: master)
More information about the linux-arm-kernel
mailing list