[PATCH 1/3] ezx: Add camera support for A780 and A910 EZX phones
Guennadi Liakhovetski
g.liakhovetski at gmx.de
Wed Nov 4 03:13:16 EST 2009
On Wed, 4 Nov 2009, Eric Miao wrote:
> Hi Antonio,
>
> Patch looks generally OK except for the MFP/GPIO usage, check my
> comments below, thanks.
>
> > +/* camera */
> > +static int a780_pxacamera_init(struct device *dev)
> > +{
> > + int err;
> > +
> > + /*
> > + * GPIO50_GPIO is CAM_EN: active low
> > + * GPIO19_GPIO is CAM_RST: active high
> > + */
> > + err = gpio_request(MFP_PIN_GPIO50, "nCAM_EN");
>
> Mmm... MFP != GPIO, so this probably should be written simply as:
>
> #define GPIO_nCAM_EN (50)
...but without parenthesis, please:
#define GPIO_nCAM_EN 50
same everywhere below
> or (which tends to be more accurate but not necessary)
>
> #define GPIO_nCAM_EN mfp_to_gpio(MFP_PIN_GPIO50)
>
> If platform matters, I suggest something like:
>
> #define GPIO_A780_nCAM_EN (50)
> #define GPIO_A910_nCAM_EN (<something else>)
>
> ...
>
> err = gpio_request(GPIO_nCAM_EN, "nCAM_EN");
>
> > + if (err) {
> > + pr_err("%s: Failed to request nCAM_EN\n", __func__);
> > + goto fail;
> > + }
> > +
> > + err = gpio_request(MFP_PIN_GPIO19, "CAM_RST");
>
> ditto
>
> > + if (err) {
> > + pr_err("%s: Failed to request CAM_RST\n", __func__);
> > + goto fail_gpio_cam_rst;
> > + }
> > +
> > + gpio_direction_output(MFP_PIN_GPIO50, 0);
> > + gpio_direction_output(MFP_PIN_GPIO19, 1);
> > +
> > + return 0;
> > +
> > +fail_gpio_cam_rst:
> > + gpio_free(MFP_PIN_GPIO50);
> > +fail:
> > + return err;
> > +}
> > +
> > +static int a780_pxacamera_power(struct device *dev, int on)
> > +{
> > + gpio_set_value(MFP_PIN_GPIO50, on ? 0 : 1);
>
> gpio_set_value(GPIO_nCAM_EN, on ? 0 : 1);
IMHO better yet
gpio_set_value(GPIO_nCAM_EN, !on);
Also throughout the patch below.
I'm still to look at it miself and maybe provide a couple more comments,
if any.
Thanks
Guennadi
>
> > +
> > +#if 0
> > + /*
> > + * This is reported to resolve the "vertical line in view finder"
> > + * issue (LIBff11930), in the original source code released by
> > + * Motorola, but we never experienced the problem, so we don't use
> > + * this for now.
> > + *
> > + * AP Kernel camera driver: set TC_MM_EN to low when camera is running
> > + * and TC_MM_EN to high when camera stops.
> > + *
> > + * BP Software: if TC_MM_EN is low, BP do not shut off 26M clock, but
> > + * BP can sleep itself.
> > + */
> > + gpio_set_value(MFP_PIN_GPIO99, on ? 0 : 1);
> > +#endif
>
> This is a little bit confusing - can we remove this for this stage?
>
> > +
> > + return 0;
> > +}
> > +
> > +static int a780_pxacamera_reset(struct device *dev)
> > +{
> > + gpio_set_value(MFP_PIN_GPIO19, 0);
> > + msleep(10);
> > + gpio_set_value(MFP_PIN_GPIO19, 1);
>
> better to define something like above:
>
> #define GPIO_CAM_RESET (19)
>
> ...
>
> gpio_set_value(GPIO_CAM_RESET, ...);
>
> > +
> > + return 0;
> > +}
> > +
> > +struct pxacamera_platform_data a780_pxacamera_platform_data = {
> > + .init = a780_pxacamera_init,
> > + .flags = PXA_CAMERA_MASTER | PXA_CAMERA_DATAWIDTH_8 |
> > + PXA_CAMERA_PCLK_EN | PXA_CAMERA_MCLK_EN,
> > + .mclk_10khz = 5000,
> > +};
> > +
> > +static struct i2c_board_info a780_camera_i2c_board_info = {
> > + I2C_BOARD_INFO("mt9m111", 0x5d),
> > +};
> > +
> > +static struct soc_camera_link a780_iclink = {
> > + .bus_id = 0,
> > + .flags = SOCAM_SENSOR_INVERT_PCLK,
> > + .i2c_adapter_id = 0,
> > + .board_info = &a780_camera_i2c_board_info,
> > + .module_name = "mt9m111",
> > + .power = a780_pxacamera_power,
> > + .reset = a780_pxacamera_reset,
> > +};
> > +
> > +static struct platform_device a780_camera = {
> > + .name = "soc-camera-pdrv",
> > + .id = 0,
> > + .dev = {
> > + .platform_data = &a780_iclink,
> > + },
> > +};
> > +
> > static struct platform_device *a780_devices[] __initdata = {
> > &a780_gpio_keys,
> > + &a780_camera,
> > };
> >
> > static void __init a780_init(void)
> > @@ -699,6 +797,8 @@ static void __init a780_init(void)
> >
> > pxa_set_keypad_info(&a780_keypad_platform_data);
> >
> > + pxa_set_camera_info(&a780_pxacamera_platform_data);
> > +
> > platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
> > platform_add_devices(ARRAY_AND_SIZE(a780_devices));
> > }
> > @@ -864,8 +964,84 @@ static struct platform_device a910_gpio_keys = {
> > },
> > };
> >
> > +/* camera */
> > +static int a910_pxacamera_init(struct device *dev)
> > +{
> > + int err;
> > +
> > + /*
> > + * GPIO50_GPIO is CAM_EN: active low
> > + * GPIO28_GPIO is CAM_RST: active high
> > + */
> > + err = gpio_request(MFP_PIN_GPIO50, "nCAM_EN");
> > + if (err) {
> > + pr_err("%s: Failed to request nCAM_EN\n", __func__);
> > + goto fail;
> > + }
> > +
> > + err = gpio_request(MFP_PIN_GPIO28, "CAM_RST");
> > + if (err) {
> > + pr_err("%s: Failed to request CAM_RST\n", __func__);
> > + goto fail_gpio_cam_rst;
> > + }
> > +
> > + gpio_direction_output(MFP_PIN_GPIO50, 0);
> > + gpio_direction_output(MFP_PIN_GPIO28, 1);
> > +
> > + return 0;
> > +
> > +fail_gpio_cam_rst:
> > + gpio_free(MFP_PIN_GPIO50);
> > +fail:
> > + return err;
> > +}
> > +
> > +static int a910_pxacamera_power(struct device *dev, int on)
> > +{
> > + gpio_set_value(MFP_PIN_GPIO50, on ? 0 : 1);
> > + return 0;
> > +}
> > +
> > +static int a910_pxacamera_reset(struct device *dev)
> > +{
> > + gpio_set_value(MFP_PIN_GPIO28, 0);
> > + msleep(10);
> > + gpio_set_value(MFP_PIN_GPIO28, 1);
> > +
> > + return 0;
> > +}
> > +
> > +struct pxacamera_platform_data a910_pxacamera_platform_data = {
> > + .init = a910_pxacamera_init,
> > + .flags = PXA_CAMERA_MASTER | PXA_CAMERA_DATAWIDTH_8 |
> > + PXA_CAMERA_PCLK_EN | PXA_CAMERA_MCLK_EN,
> > + .mclk_10khz = 5000,
> > +};
> > +
> > +static struct i2c_board_info a910_camera_i2c_board_info = {
> > + I2C_BOARD_INFO("mt9m111", 0x5d),
> > +};
> > +
> > +static struct soc_camera_link a910_iclink = {
> > + .bus_id = 0,
> > + .i2c_adapter_id = 0,
> > + .board_info = &a910_camera_i2c_board_info,
> > + .module_name = "mt9m111",
> > + .power = a910_pxacamera_power,
> > + .reset = a910_pxacamera_reset,
> > +};
> > +
> > +static struct platform_device a910_camera = {
> > + .name = "soc-camera-pdrv",
> > + .id = 0,
> > + .dev = {
> > + .platform_data = &a910_iclink,
> > + },
> > +};
> > +
> > static struct platform_device *a910_devices[] __initdata = {
> > &a910_gpio_keys,
> > + &a910_camera,
> > };
> >
> > static void __init a910_init(void)
> > @@ -880,6 +1056,8 @@ static void __init a910_init(void)
> >
> > pxa_set_keypad_info(&a910_keypad_platform_data);
> >
> > + pxa_set_camera_info(&a910_pxacamera_platform_data);
> > +
> > platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
> > platform_add_devices(ARRAY_AND_SIZE(a910_devices));
> > }
> > --
> > 1.6.5.2
> >
> >
>
---
Guennadi Liakhovetski, Ph.D.
Freelance Open-Source Software Developer
http://www.open-technology.de/
More information about the linux-arm-kernel
mailing list