[RFC PATCH 5/6] arm64: dts: amlogic: t7: add the ethernet controller

[Neil Armstrong]

On 10/4/26 16:40, Lucas Tanure wrote:
> The SoC pairs a Synopsys gigabit MAC with a small block of glue
> registers that selects the interface type and trims the clock timing,
> and with a multiplexer that points the management bus at either the
> on-chip 100M PHY or the external pins. None of it was described, so the
> port could not be used at all.
> 
> Add the controller and the multiplexer. The MAC reports a 5.10a core.
> The path the controller reaches memory over runs through a pipeline
> stage with a gate of its own, so hand that to the controller as well;
> nothing else claims it and it would otherwise be switched off as unused,
> leaving the port unable to complete a transfer.
> 
> The on-chip PHY behind the second port of the multiplexer is described
> the way the G12A does it. No board in tree uses it and that path is
> untested.
> 
> The controller is left disabled for boards to enable.
> 
> Assisted-by: LLM
> Signed-off-by: Lucas Tanure <tanure at linux.com>
> ---
>   arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi | 57 +++++++++++++++++++++
>   1 file changed, 57 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi b/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi
> index 7bd53ec16607..140f1836f3dd 100644
> --- a/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/amlogic-t7.dtsi
> @@ -250,6 +250,31 @@ gic: interrupt-controller at fff01000 {
>   			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
>   		};
>   
> +		ethmac: ethernet at fdc00000 {
> +			compatible = "amlogic,t7-dwmac",
> +				     "snps,dwmac-5.10a",
> +				     "snps,dwmac";
> +			reg = <0x0 0xfdc00000 0x0 0x10000>,
> +			      <0x0 0xfe024000 0x0 0x8>;
> +			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "macirq";
> +			clocks = <&clkc_periphs CLKID_SYS_ETH>,
> +				 <&scmi_clk CLKID_FCLK_DIV2>,
> +				 <&mpll CLKID_MPLL2>,
> +				 <&clkc_periphs CLKID_SYS_AMPIPE_ETH>;
> +			clock-names = "stmmaceth", "clkin0", "clkin1", "pipeline";
> +			power-domains = <&pwrc PWRC_T7_ETH_ID>;
> +			rx-fifo-depth = <4096>;
> +			tx-fifo-depth = <2048>;
> +			status = "disabled";
> +
> +			mdio0: mdio {
> +				compatible = "snps,dwmac-mdio";
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
> +		};
> +
>   		apb4: bus at fe000000 {
>   			compatible = "simple-bus";
>   			reg = <0x0 0xfe000000 0x0 0x480000>;
> @@ -645,6 +670,38 @@ gpio_intc: interrupt-controller at 4080 {
>   					<10 11 12 13 14 15 16 17 18 19 20 21>;
>   			};
>   
> +			eth_phy: mdio-multiplexer at 28000 {
> +				compatible = "amlogic,g12a-mdio-mux";
> +				reg = <0x0 0x28000 0x0 0xa4>;
> +				clocks = <&clkc_periphs CLKID_SYS_ETHPHY>,
> +					 <&xtal>,
> +					 <&scmi_clk CLKID_FCLK_50M>;
> +				clock-names = "pclk", "clkin0", "clkin1";
> +				mdio-parent-bus = <&mdio0>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ext_mdio: mdio at 0 {
> +					reg = <0>;
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +				};
> +
> +				int_mdio: mdio at 1 {
> +					reg = <1>;
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					internal_ephy: ethernet-phy at 8 {
> +						compatible = "ethernet-phy-id0180.3301",
> +							     "ethernet-phy-ieee802.3-c22";
> +						interrupts = <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>;
> +						reg = <8>;
> +						max-speed = <100>;
> +					};
> +				};
> +			};
> +
>   			uart_a: serial at 78000 {
>   				compatible = "amlogic,t7-uart", "amlogic,meson-s4-uart";
>   				reg = <0x0 0x78000 0x0 0x18>;

Reviewed-by: Neil Armstrong <neil.armstrong at linaro.org>

Thanks,
Neil