[PATCH re-send] drm/meson: add support for higher bandwidth HDMI DTDs

[neil.armstrong at linaro.org]

On 11/2/26 22:28, Martin Blumenstingl wrote:
> There's a report from a user with a DELL U3415W monitor and a Khadas
> VIM3 stating that 3440x1440 at 50Hz works but 3440x1440 at 60Hz doesn't.
> edid-decode Detailed Timing Descriptor (DTD) extract of that mode:
>    DTD 1:  3440x1440   59.972616 Hz  43:18    88.819 kHz    319.750000 MHz
>                 Hfront   80 Hsync  32 Hback   48 Hpol P
>                 Vfront   28 Vsync  10 Vback    3 Vpol N
> 
> Those high clock rates are currently not supported by the meson_vclk
> code as it limits the PLL OD (output divider) to a minimum of 2. The
> formula to calculate the clock internally is (ignoring fractional
> dividers):
>    319.750MHz * 10 * od = 24MHz * m
> 
> With od = 2 this results in m = 266, which is outside the supported
> range of the PLL on G12A SoCs (the driver limits m to 106..247).
> Using od = 2 results in m = 133, which is supported.
> 
> Allow the driver to pick OD = 1 to gain support for modes such as
> 3440x1440 at 60Hz.
> 
> Link: https://forum.khadas.com/t/can-not-set-display-resolution-to-3440x1440-for-dell-monitor/26271/12
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> ---
> Re-send of [0] which seems to have slipped through.
> 
> 
> [0] https://lore.kernel.org/linux-amlogic/20260109204836.790096-1-martin.blumenstingl@googlemail.com/
> 
> 
>   drivers/gpu/drm/meson/meson_vclk.c | 6 +++---
>   1 file changed, 3 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/gpu/drm/meson/meson_vclk.c b/drivers/gpu/drm/meson/meson_vclk.c
> index dfe0c28a0f05..c0be0b7655bf 100644
> --- a/drivers/gpu/drm/meson/meson_vclk.c
> +++ b/drivers/gpu/drm/meson/meson_vclk.c
> @@ -700,8 +700,8 @@ static bool meson_hdmi_pll_find_params(struct meson_drm *priv,
>   				       unsigned int *frac,
>   				       unsigned int *od)
>   {
> -	/* Cycle from /16 to /2 */
> -	for (*od = 16 ; *od > 1 ; *od >>= 1) {
> +	/* Cycle from /16 to /1 */
> +	for (*od = 16 ; *od > 0 ; *od >>= 1) {
>   		*m = meson_hdmi_pll_get_m(priv, freq * *od);
>   		if (!*m)
>   			continue;
> @@ -750,7 +750,7 @@ static void meson_hdmi_pll_generic_set(struct meson_drm *priv,
>   		/* OD2 goes to the PHY, and needs to be *10, so keep OD3=1 */
>   		od3 = 1;
>   		if (od < 4) {
> -			od1 = 2;
> +			od1 = od;
>   			od2 = 1;
>   		} else {
>   			od2 = od / 4;

Reviewed-by: Neil Armstrong <neil.armstrong at linaro.org>

Thanks,
Neil