[PATCH] arm64: dts: amlogic: enable some device nodes for S4
Xianwei Zhao via B4 Relay
devnull+xianwei.zhao.amlogic.com at kernel.org
Thu Jul 4 22:39:16 PDT 2024
From: Xianwei Zhao <xianwei.zhao at amlogic.com>
Enable some device nodes for AQ222 base S4, including
SD, regulator and ethnernet node.
Signed-off-by: Xianwei Zhao <xianwei.zhao at amlogic.com>
---
.../boot/dts/amlogic/meson-s4-s805x2-aq222.dts | 146 +++++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-s4.dtsi | 128 ++++++++++++++++++
2 files changed, 274 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts b/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
index 983caddc409c..2ab685d9bd1d 100644
--- a/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
@@ -34,6 +34,112 @@ secmon_reserved: secmon at 5000000 {
no-map;
};
};
+
+ sdio_32k: sdio-32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&sdio_32k>;
+ clock-names = "ext_clock";
+ };
+
+ main_12v: regulator-main-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-always-on;
+ };
+
+ vddio_ao1v8: regulator-vddio-ao1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ /* SY8120B1ABC DC/DC Regulator. */
+ vddcpu: regulator-vddcpu {
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU";
+ regulator-min-microvolt = <689000>;
+ regulator-max-microvolt = <1049000>;
+
+ vin-supply = <&main_12v>;
+
+ pwms = <&pwm_ij 1 1500 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ /* Voltage Duty-Cycle */
+ voltage-table = <1049000 0>,
+ <1039000 3>,
+ <1029000 6>,
+ <1019000 9>,
+ <1009000 12>,
+ <999000 14>,
+ <989000 17>,
+ <979000 20>,
+ <969000 23>,
+ <959000 26>,
+ <949000 29>,
+ <939000 31>,
+ <929000 34>,
+ <919000 37>,
+ <909000 40>,
+ <899000 43>,
+ <889000 45>,
+ <879000 48>,
+ <869000 51>,
+ <859000 54>,
+ <849000 56>,
+ <839000 59>,
+ <829000 62>,
+ <819000 65>,
+ <809000 68>,
+ <799000 70>,
+ <789000 73>,
+ <779000 76>,
+ <769000 79>,
+ <759000 81>,
+ <749000 84>,
+ <739000 87>,
+ <729000 89>,
+ <719000 92>,
+ <709000 95>,
+ <699000 98>,
+ <689000 100>;
+ status = "okay";
+ };
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins1>;
+ pinctrl-names = "default";
+};
+
+&pwm_ij {
+ status = "okay";
};
&uart_b {
@@ -46,6 +152,40 @@ &ir {
pinctrl-names = "default";
};
+&sdio {
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ no-sd;
+ no-mmc;
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_ao1v8>;
+};
+
+&sd {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_3v3>;
+};
+
&nand {
status = "okay";
#address-cells = <1>;
@@ -90,3 +230,9 @@ &spicc0 {
pinctrl-0 = <&spicc0_pins_x>;
cs-gpios = <&gpio GPIOX_10 GPIO_ACTIVE_LOW>;
};
+
+ðmac {
+ status = "okay";
+ phy-handle = <&internal_ephy>;
+ phy-mode = "rmii";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-s4.dtsi b/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
index b686eacb9662..c11c947fa18c 100644
--- a/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
@@ -10,6 +10,7 @@
#include <dt-bindings/clock/amlogic,s4-pll-clkc.h>
#include <dt-bindings/clock/amlogic,s4-peripherals-clkc.h>
#include <dt-bindings/power/meson-s4-power.h>
+#include <dt-bindings/reset/amlogic,meson-s4-reset.h>
/ {
cpus {
@@ -466,6 +467,93 @@ mux {
};
};
+ sdcard_pins: sdcard-pins {
+ mux {
+ groups = "sdcard_d0_c",
+ "sdcard_d1_c",
+ "sdcard_d2_c",
+ "sdcard_d3_c",
+ "sdcard_clk_c",
+ "sdcard_cmd_c";
+ function = "sdcard";
+ bias-pull-up;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ sdcard_clk_gate_pins: sdcard-clk-gate-pins {
+ mux {
+ groups = "GPIOC_4";
+ function = "gpio_periphs";
+ bias-pull-down;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ emmc_pins: emmc-pins {
+ mux-0 {
+ groups = "emmc_nand_d0",
+ "emmc_nand_d1",
+ "emmc_nand_d2",
+ "emmc_nand_d3",
+ "emmc_nand_d4",
+ "emmc_nand_d5",
+ "emmc_nand_d6",
+ "emmc_nand_d7",
+ "emmc_cmd";
+ function = "emmc";
+ bias-pull-up;
+ drive-strength-microamp = <4000>;
+ };
+ mux-1 {
+ groups = "emmc_clk";
+ function = "emmc";
+ bias-pull-up;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ emmc_ds_pins: emmc-ds-pins {
+ mux {
+ groups = "emmc_nand_ds";
+ function = "emmc";
+ bias-pull-down;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ emmc_clk_gate_pins: emmc-clk-gate-pins {
+ mux {
+ groups = "GPIOB_8";
+ function = "gpio_periphs";
+ bias-pull-down;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ sdio_pins: sdio-pins {
+ mux {
+ groups = "sdio_d0",
+ "sdio_d1",
+ "sdio_d2",
+ "sdio_d3",
+ "sdio_clk",
+ "sdio_cmd";
+ function = "sdio";
+ bias-pull-up;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ sdio_clk_gate_pins: sdio-clk-gate-pins {
+ mux {
+ groups = "GPIOX_4";
+ function = "gpio_periphs";
+ bias-pull-down;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
spicc0_pins_x: spicc0-pins_x {
mux {
groups = "spi_a_mosi_x",
@@ -712,5 +800,45 @@ mdio0: mdio {
compatible = "snps,dwmac-mdio";
};
};
+
+ sdio: mmc at fe088000 {
+ compatible = "amlogic,meson-axg-mmc";
+ reg = <0x0 0xfe088000 0x0 0x800>;
+ interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc_periphs CLKID_SDEMMC_A>,
+ <&xtal>,
+ <&clkc_pll CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ resets = <&reset RESET_SD_EMMC_A>;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ status = "disabled";
+ };
+
+ sd: mmc at fe08a000 {
+ compatible = "amlogic,meson-axg-mmc";
+ reg = <0x0 0xfe08a000 0x0 0x800>;
+ interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_periphs CLKID_SDEMMC_B>,
+ <&clkc_periphs CLKID_SD_EMMC_B>,
+ <&clkc_pll CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ resets = <&reset RESET_SD_EMMC_B>;
+ status = "disabled";
+ };
+
+ emmc: mmc at fe08c000 {
+ compatible = "amlogic,meson-axg-mmc";
+ reg = <0x0 0xfe08c000 0x0 0x800>;
+ interrupts = <GIC_SPI 178 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_periphs CLKID_NAND>,
+ <&xtal>,
+ <&clkc_pll CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ resets = <&reset RESET_NAND_EMMC>;
+ no-sdio;
+ no-sd;
+ status = "disabled";
+ };
};
};
---
base-commit: 338c92a5d1956f1841f84b86923087676d1d0cea
change-id: 20240705-s4_node-8110e3286c0c
Best regards,
--
Xianwei Zhao <xianwei.zhao at amlogic.com>
More information about the linux-amlogic
mailing list