[PATCH v2 2/3] arm64: dts: amlogic: add some device nodes for C3
Xianwei Zhao via B4 Relay
devnull+xianwei.zhao.amlogic.com at kernel.org
Tue Aug 20 02:41:57 PDT 2024
From: Xianwei Zhao <xianwei.zhao at amlogic.com>
Add some device nodes for SoC C3, including periphs clock controller
node, PLL clock controller node, SPICC node, regulator node, NAND
controller node, sdcard node, Ethernet MAC and PHY node.
The sdacrd depends on regulator and pinctrl(select), so some
property fields are placed at the board level. The nand chip
is placed on the board, So some property fields about SPIFC
and NAND controller node are placed at the board level.
THe Ethernet MAC support outchip PHY, so place this property
field(select PHY) at the board level.
Signed-off-by: Xianwei Zhao <xianwei.zhao at amlogic.com>
---
.../boot/dts/amlogic/amlogic-c3-c302x-aw409.dts | 233 ++++++++++
arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi | 487 ++++++++++++++++++++-
2 files changed, 719 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/amlogic/amlogic-c3-c302x-aw409.dts b/arch/arm64/boot/dts/amlogic/amlogic-c3-c302x-aw409.dts
index edce8850b338..b8d2037afc00 100644
--- a/arch/arm64/boot/dts/amlogic/amlogic-c3-c302x-aw409.dts
+++ b/arch/arm64/boot/dts/amlogic/amlogic-c3-c302x-aw409.dts
@@ -16,14 +16,247 @@ / {
aliases {
serial0 = &uart_b;
+ spi0 = &spifc;
};
memory at 0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x10000000>;
};
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 9 MiB reserved for ARM Trusted Firmware */
+ secmon_reserved: secmon at 7f00000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x07f00000 0x0 0x900000>;
+ no-map;
+ };
+ };
+
+ main_12v: regulator-main-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&main_12v>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddq: regulator-vddq {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDQ";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <&main_12v>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddao_1v8: regulator-vddao-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ddr4_2v5: regulator-ddr4-2v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "DDR4_2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vcc_1v8: regulator-vcc-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd_1v8: regulator-vdd-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD1V8_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddio_b: regulator-vddio-3v3-b {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_B";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sdcard: regulator-sdcard {
+ compatible = "regulator-fixed";
+ regulator-name = "SDCARD_POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ gpio = <&gpio GPIOA_4 GPIO_ACTIVE_LOW>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
};
&uart_b {
status = "okay";
};
+
+&nand {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand at 0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ nand-on-flash-bbt;
+
+ partition at 0 {
+ label = "boot";
+ reg = <0x0 0x00200000>;
+ };
+ partition at 200000 {
+ label = "env";
+ reg = <0x00200000 0x00400000>;
+ };
+ partition at 600000 {
+ label = "system";
+ reg = <0x00600000 0x00a00000>;
+ };
+ partition at 1000000 {
+ label = "rootfs";
+ reg = <0x01000000 0x03000000>;
+ };
+ partition at 4000000 {
+ label = "media";
+ reg = <0x04000000 0x8000000>;
+ };
+ };
+};
+
+ðmac {
+ status = "okay";
+ phy-handle = <&internal_ephy>;
+ phy-mode = "rmii";
+};
+
+&spifc {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-0 = <&spifc_pins>;
+ pinctrl-names = "default";
+
+ nand at 0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <83000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "disabled";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "boot";
+ reg = <0 0x200000>;
+ };
+
+ partition at 200000 {
+ label = "env";
+ reg = <0x200000 0x400000>;
+ };
+
+ partition at 600000 {
+ label = "system";
+ reg = <0x600000 0xa00000>;
+ };
+
+ partition at 1000000 {
+ label = "rootfs";
+ reg = <0x1000000 0x3000000>;
+ };
+
+ partition at 4000000 {
+ label = "data";
+ reg = <0x4000000 0x8000000>;
+ };
+ };
+ };
+};
+
+&sd {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default","clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&sdcard>;
+ vqmmc-supply = <&sdcard>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi b/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi
index f8fb060c49ae..2bf56fbe3dfb 100644
--- a/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi
+++ b/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi
@@ -7,6 +7,11 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/reset/amlogic,c3-reset.h>
+#include <dt-bindings/clock/amlogic,c3-pll-clkc.h>
+#include <dt-bindings/clock/amlogic,c3-scmi-clkc.h>
+#include <dt-bindings/clock/amlogic,c3-peripherals-clkc.h>
+#include <dt-bindings/power/amlogic,c3-pwrc.h>
+#include <dt-bindings/gpio/amlogic-c3-gpio.h>
/ {
cpus {
@@ -57,6 +62,34 @@ pwrc: power-controller {
};
};
+ sram {
+ compatible = "mmio-sram";
+ reg = <0x0 0x07f50e00 0x0 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x0 0x07f50e00 0x100>;
+
+ scmi_shmem: sram at 0 {
+ compatible = "arm,scmi-shmem";
+ reg = <0x0 0x100>;
+ };
+ };
+
+ firmware {
+ scmi: scmi {
+ compatible = "arm,scmi-smc";
+ arm,smc-id = <0x820000C1>;
+ shmem = <&scmi_shmem>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ scmi_clk: protocol at 14 {
+ reg = <0x14>;
+ #clock-cells = <1>;
+ };
+ };
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <2>;
@@ -108,6 +141,237 @@ gpio: bank at 4000 {
#gpio-cells = <2>;
gpio-ranges = <&periphs_pinctrl 0 0 55>;
};
+
+ i2c0_pins1: i2c0-pins1 {
+ mux {
+ groups = "i2c0_sda_e",
+ "i2c0_scl_e";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c0_pins2: i2c0-pins2 {
+ mux {
+ groups = "i2c0_sda_d",
+ "i2c0_scl_d";
+ function = "i2c0";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_pins1: i2c1-pins1 {
+ mux {
+ groups = "i2c1_sda_x",
+ "i2c1_scl_x";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_pins2: i2c1-pins2 {
+ mux {
+ groups = "i2c1_sda_d",
+ "i2c1_scl_d";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_pins3: i2c1-pins3 {
+ mux {
+ groups = "i2c1_sda_a",
+ "i2c1_scl_a";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c1_pins4: i2c1-pins4 {
+ mux {
+ groups = "i2c1_sda_b",
+ "i2c1_scl_b";
+ function = "i2c1";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c2_pins1: i2c2-pins1 {
+ mux {
+ groups = "i2c2_sda",
+ "i2c2_scl";
+ function = "i2c2";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_pins1: i2c3-pins1 {
+ mux {
+ groups = "i2c3_sda_c",
+ "i2c3_scl_c";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_pins2: i2c3-pins2 {
+ mux {
+ groups = "i2c3_sda_x",
+ "i2c3_scl_x";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ i2c3_pins3: i2c3-pins3 {
+ mux {
+ groups = "i2c3_sda_d",
+ "i2c3_scl_d";
+ function = "i2c3";
+ bias-disable;
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ nand_pins: nand-pins {
+ mux {
+ groups = "emmc_nand_d0",
+ "emmc_nand_d1",
+ "emmc_nand_d2",
+ "emmc_nand_d3",
+ "emmc_nand_d4",
+ "emmc_nand_d5",
+ "emmc_nand_d6",
+ "emmc_nand_d7",
+ "nand_ce0",
+ "nand_ale",
+ "nand_cle",
+ "nand_wen_clk",
+ "nand_ren_wr";
+ function = "nand";
+ input-enable;
+ };
+ };
+
+ sdcard_pins: sdcard-pins {
+ mux {
+ groups = "sdcard_d0",
+ "sdcard_d1",
+ "sdcard_d2",
+ "sdcard_d3",
+ "sdcard_clk",
+ "sdcard_cmd";
+ function = "sdcard";
+ bias-pull-up;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ sdcard_clk_gate_pins: sdcard-clk-cmd-pins {
+ mux {
+ groups = "GPIOC_4";
+ function = "gpio_periphs";
+ bias-pull-down;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ sdio_m_clk_gate_pins: sdio-m-clk-cmd-pins {
+ mux {
+ groups = "sdio_clk";
+ function = "sdio";
+ bias-pull-down;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ sdio_m_pins: sdio-m-all-pins {
+ mux {
+ groups = "sdio_d0",
+ "sdio_d1",
+ "sdio_d2",
+ "sdio_d3",
+ "sdio_clk",
+ "sdio_cmd";
+ function = "sdio";
+ input-enable;
+ bias-pull-up;
+ drive-strength-microamp = <4000>;
+ };
+ };
+
+ spicc0_pins1: spicc0-pins1 {
+ mux {
+ groups = "spi_a_mosi_b",
+ "spi_a_miso_b",
+ "spi_a_clk_b";
+ function = "spi_a";
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ spicc0_pins2: spicc0-pins2 {
+ mux {
+ groups = "spi_a_mosi_c",
+ "spi_a_miso_c",
+ "spi_a_clk_c";
+ function = "spi_a";
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ spicc0_pins3: spicc0-pins3 {
+ mux {
+ groups = "spi_a_mosi_x",
+ "spi_a_miso_x",
+ "spi_a_clk_x";
+ function = "spi_a";
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ spicc1_pins1: spicc1-pins1 {
+ mux {
+ groups = "spi_b_mosi_d",
+ "spi_b_miso_d",
+ "spi_b_clk_d";
+ function = "spi_b";
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ spicc1_pins2: spicc1-pins2 {
+ mux {
+ groups = "spi_b_mosi_x",
+ "spi_b_miso_x",
+ "spi_b_clk_x";
+ function = "spi_b";
+ drive-strength-microamp = <3000>;
+ };
+ };
+
+ spifc_pins: spifc-pins {
+ mux {
+ groups = "spif_mo",
+ "spif_mi",
+ "spif_clk",
+ "spif_cs",
+ "spif_hold",
+ "spif_wp",
+ "spif_clk_loop";
+ function = "spif";
+ drive-strength-microamp = <4000>;
+ };
+ };
};
gpio_intc: interrupt-controller at 4080 {
@@ -119,16 +383,237 @@ gpio_intc: interrupt-controller at 4080 {
<10 11 12 13 14 15 16 17 18 19 20 21>;
};
+ clkc_pll: clock-controller at 8000 {
+ compatible = "amlogic,c3-pll-clkc";
+ reg = <0x0 0x8000 0x0 0x1a4>;
+ #clock-cells = <1>;
+ clocks = <&scmi_clk CLKID_TOP_PLL_OSC>,
+ <&scmi_clk CLKID_MCLK_PLL_OSC>,
+ <&scmi_clk CLKID_FIXED_PLL_OSC>;
+ clock-names = "top",
+ "mclk",
+ "fix";
+ };
+
+ clkc_periphs: clock-controller at 0 {
+ compatible = "amlogic,c3-peripherals-clkc";
+ reg = <0x0 0x0 0x0 0x49c>;
+ #clock-cells = <1>;
+ clocks = <&xtal>,
+ <&scmi_clk CLKID_OSC>,
+ <&scmi_clk CLKID_FIXED_PLL_OSC>,
+ <&clkc_pll CLKID_FCLK_DIV2>,
+ <&clkc_pll CLKID_FCLK_DIV2P5>,
+ <&clkc_pll CLKID_FCLK_DIV3>,
+ <&clkc_pll CLKID_FCLK_DIV4>,
+ <&clkc_pll CLKID_FCLK_DIV5>,
+ <&clkc_pll CLKID_FCLK_DIV7>,
+ <&clkc_pll CLKID_GP0_PLL>,
+ <&scmi_clk CLKID_GP1_PLL_OSC>,
+ <&clkc_pll CLKID_HIFI_PLL>,
+ <&scmi_clk CLKID_SYS_CLK>,
+ <&scmi_clk CLKID_AXI_CLK>,
+ <&scmi_clk CLKID_SYS_PLL_DIV16>,
+ <&scmi_clk CLKID_CPU_CLK_DIV16>;
+ clock-names = "xtal_24m",
+ "oscin",
+ "fix",
+ "fdiv2",
+ "fdiv2p5",
+ "fdiv3",
+ "fdiv4",
+ "fdiv5",
+ "fdiv7",
+ "gp0",
+ "gp1",
+ "hifi",
+ "sysclk",
+ "axiclk",
+ "sysplldiv16",
+ "cpudiv16";
+ };
+
+ eth_phy: mdio-multiplexer at 28000 {
+ compatible = "amlogic,g12a-mdio-mux";
+ reg = <0x0 0x28000 0x0 0xa4>;
+
+ clocks = <&clkc_periphs CLKID_SYS_ETH_PHY>,
+ <&xtal>,
+ <&clkc_pll CLKID_FCLK_50M>;
+ clock-names = "pclk", "clkin0", "clkin1";
+ mdio-parent-bus = <&mdio0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ext_mdio: mdio at 0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ int_mdio: mdio at 1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ internal_ephy: ethernet_phy at 8 {
+ compatible = "ethernet-phy-id0180.3301",
+ "ethernet-phy-ieee802.3-c22";
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <8>;
+ max-speed = <100>;
+ };
+ };
+ };
+
+ spicc0: spi at 50000 {
+ compatible = "amlogic,meson-g12a-spicc";
+ reg = <0x0 0x50000 0x0 0x44>;
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc_periphs CLKID_SYS_SPICC_0>,
+ <&clkc_periphs CLKID_SPICC_A>;
+ clock-names = "core", "pclk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spicc1: spi at 52000 {
+ compatible = "amlogic,meson-g12a-spicc";
+ reg = <0x0 0x52000 0x0 0x44>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc_periphs CLKID_SYS_SPICC_1>,
+ <&clkc_periphs CLKID_SPICC_B>;
+ clock-names = "core", "pclk";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ spifc: spi at 56000 {
+ compatible = "amlogic,a1-spifc";
+ reg = <0x0 0x56000 0x0 0x290>;
+ interrupts = <GIC_SPI 182 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_periphs CLKID_SPIFC>;
+ clock-names = "core";
+ status = "disabled";
+ };
+
+ i2c0: i2c at 66000 {
+ compatible = "amlogic,meson-axg-i2c";
+ reg = <0x0 0x66000 0x0 0x24>;
+ interrupts = <GIC_SPI 160 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc_periphs CLKID_SYS_I2C_M_A>;
+ status = "disabled";
+ };
+
+ i2c1: i2c at 68000 {
+ compatible = "amlogic,meson-axg-i2c";
+ reg = <0x0 0x68000 0x0 0x24>;
+ interrupts = <GIC_SPI 161 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc_periphs CLKID_SYS_I2C_M_B>;
+ status = "disabled";
+ };
+
+ i2c2: i2c at 6a000 {
+ compatible = "amlogic,meson-axg-i2c";
+ reg = <0x0 0x6a000 0x0 0x24>;
+ interrupts = <GIC_SPI 162 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc_periphs CLKID_SYS_I2C_M_C>;
+ status = "disabled";
+ };
+
+ i2c3: i2c at 6c000 {
+ compatible = "amlogic,meson-axg-i2c";
+ reg = <0x0 0x6c000 0x0 0x24>;
+ interrupts = <GIC_SPI 163 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc_periphs CLKID_SYS_I2C_M_D>;
+ status = "disabled";
+ };
+
uart_b: serial at 7a000 {
compatible = "amlogic,meson-s4-uart",
"amlogic,meson-ao-uart";
reg = <0x0 0x7a000 0x0 0x18>;
interrupts = <GIC_SPI 169 IRQ_TYPE_EDGE_RISING>;
status = "disabled";
- clocks = <&xtal>, <&xtal>, <&xtal>;
+ clocks = <&xtal>, <&clkc_periphs CLKID_SYS_UART_B>, <&xtal>;
clock-names = "xtal", "pclk", "baud";
};
+ sdio: mmc at 88000 {
+ compatible = "amlogic,meson-axg-mmc";
+ reg = <0x0 0x88000 0x0 0x800>;
+ interrupts = <GIC_SPI 176 IRQ_TYPE_EDGE_RISING>;
+ power-domains = <&pwrc PWRC_C3_SDIOA_ID>;
+ clocks = <&clkc_periphs CLKID_SYS_SD_EMMC_A>,
+ <&clkc_periphs CLKID_SD_EMMC_A>,
+ <&clkc_pll CLKID_FCLK_DIV2>;
+ clock-names = "core","clkin0", "clkin1";
+ no-mmc;
+ no-sd;
+ resets = <&reset RESET_SD_EMMC_A>;
+ status = "disabled";
+ };
+
+ sd: mmc at 8a000 {
+ compatible = "amlogic,meson-axg-mmc";
+ reg = <0x0 0x8a000 0x0 0x800>;
+ interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
+ power-domains = <&pwrc PWRC_C3_SDCARD_ID>;
+ clocks = <&clkc_periphs CLKID_SYS_SD_EMMC_B>,
+ <&clkc_periphs CLKID_SD_EMMC_B>,
+ <&clkc_pll CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ no-mmc;
+ no-sdio;
+ resets = <&reset RESET_SD_EMMC_B>;
+ status = "disabled";
+ };
+
+ nand: nand-controller at 8d000 {
+ compatible = "amlogic,meson-axg-nfc";
+ reg = <0x0 0x8d000 0x0 0x200>,
+ <0x0 0x8C000 0x0 0x4>;
+ reg-names = "nfc", "emmc";
+ interrupts = <GIC_SPI 87 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_periphs CLKID_SYS_SD_EMMC_C>,
+ <&clkc_pll CLKID_FCLK_DIV2>;
+ clock-names = "core", "device";
+ status = "disabled";
+ };
+ };
+
+ ethmac: ethernet at fdc00000 {
+ compatible = "amlogic,meson-g12a-dwmac",
+ "snps,dwmac-3.70a",
+ "snps,dwmac";
+ reg = <0x0 0xfdc00000 0x0 0x10000>,
+ <0x0 0xfe024000 0x0 0x8>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ power-domains = <&pwrc PWRC_C3_ETH_ID>;
+ clocks = <&clkc_periphs CLKID_SYS_ETH_MAC>,
+ <&clkc_pll CLKID_FCLK_DIV2>,
+ <&clkc_pll CLKID_FCLK_50M>;
+ clock-names = "stmmaceth", "clkin0", "clkin1";
+ rx-fifo-depth = <4096>;
+ tx-fifo-depth = <2048>;
+ status = "disabled";
+
+ mdio0: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
};
};
--
2.37.1
More information about the linux-amlogic
mailing list