[PATCH 4/5] arm64: dts: meson: u200: use TDM C for HDMI

[Jerome Brunet]

On the u200, TDM B is wired to the onboard AD82584F i2c speaker codec.
This makes TDM B a poor choice for the interface dedicated to HDMI which
uses 4 i2s lanes.

TDM A is not a good choice either as it is connected to the SDIO wifi/bt
chip.

TDM C is not used externally by default, which makes it a better choice for
the HDMI interface.

Signed-off-by: Jerome Brunet <jbrunet at baylibre.com>
---
 arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
index 921b62c5ab33..da66e2e1dffb 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
@@ -159,10 +159,10 @@ vddcpu: regulator-vddcpu {
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "U200";
-		audio-aux-devs = <&tdmout_b>;
-		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
-				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
-				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+		audio-aux-devs = <&tdmout_c>;
+		audio-routing = "TDMOUT_C IN 0", "FRDDR_A OUT 2",
+				"TDMOUT_C IN 1", "FRDDR_B OUT 2",
+				"TDMOUT_C IN 2", "FRDDR_C OUT 2",
 				"TDM_B Playback", "TDMOUT_B OUT",
 				"SPDIFOUT IN 0", "FRDDR_A OUT 3",
 				"SPDIFOUT IN 1", "FRDDR_B OUT 3",
@@ -193,7 +193,7 @@ dai-link-2 {
 
 		/* 8ch hdmi interface */
 		dai-link-3 {
-			sound-dai = <&tdmif_b>;
+			sound-dai = <&tdmif_c>;
 			dai-format = "i2s";
 			dai-tdm-slot-tx-mask-0 = <1 1>;
 			dai-tdm-slot-tx-mask-1 = <1 1>;
@@ -202,7 +202,7 @@ dai-link-3 {
 			mclk-fs = <256>;
 
 			codec {
-				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_C>;
 			};
 		};
 
@@ -412,11 +412,11 @@ &spdifout_b {
 	status = "okay";
 };
 
-&tdmif_b {
+&tdmif_c {
 	status = "okay";
 };
 
-&tdmout_b {
+&tdmout_c {
 	status = "okay";
 };
 
-- 
2.40.1