[PATCH v2] mmc: meson-mx-sdhc: Fix initialization frozen issue
Linux regression tracking (Thorsten Leemhuis)
regressions at leemhuis.info
Wed Oct 25 03:16:37 PDT 2023
On 23.10.23 13:14, Ulf Hansson wrote:
> On Tue, 10 Oct 2023 at 18:44, Ziyang Huang <hzyitc at outlook.com> wrote:
>>
>> Commit 4bc31edebde5 ("mmc: core: Set HS clock speed before sending
>> HS CMD13") set HS clock (52MHz) before switching to HS mode. For this
>> freq, FCLK_DIV5 will be selected and div value is 10 (reg value is 9).
>> Then we set rx_clk_phase to 11 or 15 which is out of range and make
>> hardware frozen. After we send command request, no irq will be
>> interrupted and the mmc driver will keep to wait for request finished,
>> even durning rebooting.
>>
>> So let's set it to Phase 90 which should work in most cases. Then let
>> meson_mx_sdhc_execute_tuning() to find the accurate value for data
>> transfer.
>>
>> If this doesn't work, maybe need to define a factor in dts.
>>
>> Fixes: e4bf1b0970ef ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
>> Signed-off-by: Ziyang Huang <hzyitc at outlook.com>
>
> I have re-added Thorsten to see if he has some time to test this on his end.
FWIW, I was only involved wrt to regression tracking. It iirc was was
Martin that had reported the problem here:
https://lore.kernel.org/all/CAFBinCD0RT0p-jk86W0JuMT3ufohRh1RqWCcM35DKZJpuc10HQ@mail.gmail.com/
Side note: a proper Reported-by: tag together with a Link or Closes tag
would be good to have in the patch descriptions, as explained in the Docs.
Ciao, Thorsten
>> ---
>> Changes since v1:
>> Use Phase 90 instand of value 1
>>
>> drivers/mmc/host/meson-mx-sdhc-mmc.c | 26 +++++---------------------
>> 1 file changed, 5 insertions(+), 21 deletions(-)
>>
>> diff --git a/drivers/mmc/host/meson-mx-sdhc-mmc.c b/drivers/mmc/host/meson-mx-sdhc-mmc.c
>> index 97168cdfa8e9..29698fceb89c 100644
>> --- a/drivers/mmc/host/meson-mx-sdhc-mmc.c
>> +++ b/drivers/mmc/host/meson-mx-sdhc-mmc.c
>> @@ -269,7 +269,7 @@ static int meson_mx_sdhc_enable_clks(struct mmc_host *mmc)
>> static int meson_mx_sdhc_set_clk(struct mmc_host *mmc, struct mmc_ios *ios)
>> {
>> struct meson_mx_sdhc_host *host = mmc_priv(mmc);
>> - u32 rx_clk_phase;
>> + u32 val, rx_clk_phase;
>> int ret;
>>
>> meson_mx_sdhc_disable_clks(mmc);
>> @@ -290,27 +290,11 @@ static int meson_mx_sdhc_set_clk(struct mmc_host *mmc, struct mmc_ios *ios)
>> mmc->actual_clock = clk_get_rate(host->sd_clk);
>>
>> /*
>> - * according to Amlogic the following latching points are
>> - * selected with empirical values, there is no (known) formula
>> - * to calculate these.
>> + * Phase 90 should work in most cases. For data transmission,
>> + * meson_mx_sdhc_execute_tuning() will find a accurate value
>> */
>> - if (mmc->actual_clock > 100000000) {
>> - rx_clk_phase = 1;
>> - } else if (mmc->actual_clock > 45000000) {
>> - if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330)
>> - rx_clk_phase = 15;
>> - else
>> - rx_clk_phase = 11;
>> - } else if (mmc->actual_clock >= 25000000) {
>> - rx_clk_phase = 15;
>> - } else if (mmc->actual_clock > 5000000) {
>> - rx_clk_phase = 23;
>> - } else if (mmc->actual_clock > 1000000) {
>> - rx_clk_phase = 55;
>> - } else {
>> - rx_clk_phase = 1061;
>> - }
>> -
>> + regmap_read(host->regmap, MESON_SDHC_CLKC, &val);
>> + rx_clk_phase = FIELD_GET(MESON_SDHC_CLKC_CLK_DIV, val) / 4;
>> regmap_update_bits(host->regmap, MESON_SDHC_CLK2,
>> MESON_SDHC_CLK2_RX_CLK_PHASE,
>> FIELD_PREP(MESON_SDHC_CLK2_RX_CLK_PHASE,
>> --
>> 2.34.1
>>
>
More information about the linux-amlogic
mailing list