[PATCH 2/2] arm64: dts: amlogic: add libretech cottonwood support
Jerome Brunet
jbrunet at baylibre.com
Wed Oct 4 02:49:00 PDT 2023
On Wed 04 Oct 2023 at 11:20, Neil Armstrong <neil.armstrong at linaro.org> wrote:
> On 02/10/2023 16:10, Jerome Brunet wrote:
>> Add support for the Libretech cottonwood board family.
>> These 2 boards are based on the same PCB, with an RPi B form factor.
>> The "Alta" board uses an a311d while the "Solitude" variant uses an
>> s905d3.
>> Co-developed-by: Da Xue <da.xue at libretech.co>
>> Signed-off-by: Da Xue <da.xue at libretech.co>
>> Signed-off-by: Jerome Brunet <jbrunet at baylibre.com>
>> ---
>> arch/arm64/boot/dts/amlogic/Makefile | 2 +
>> .../amlogic/meson-g12b-a311d-libretech-cc.dts | 133 ++++
>> .../amlogic/meson-libretech-cottonwood.dtsi | 610 ++++++++++++++++++
>> .../amlogic/meson-sm1-s905d3-libretech-cc.dts | 89 +++
>> 4 files changed, 834 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-a311d-libretech-cc.dts
>> create mode 100644 arch/arm64/boot/dts/amlogic/meson-libretech-cottonwood.dtsi
>> create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-s905d3-libretech-cc.dts
>>
>
> <snip>
>
>> +
>> + leds-pwm {
>> + compatible = "pwm-leds";
>> +
>> + led-green {
>> + color = <LED_COLOR_ID_GREEN>;
>> + function = LED_FUNCTION_STATUS;
>> + linux,default-trigger = "default-on";
>> + panic-indicator;
>> + max-brightness = <255>;
>> + pwms = <&pwm_cd 1 1250 0>;
>> + active-low;
>> + };
>> +
>> + led-blue {
>> + color = <LED_COLOR_ID_BLUE>;
>> + function = LED_FUNCTION_ACTIVITY;
>> + linux,default-trigger = "activity";
>
> "activity" isn't documented, perhaps heartbeat instead ?
>
The trigger does exist though. The other way is to extend the DT doc.
I don't really care one way or the other
I'll defer to Da on this one
>> + max-brightness = <255>;
>> + pwms = <&pwm_ab 1 1250 0>;
>> + active-low;
>> + };
>
> leds subnodes should be named as led(-[0-9a-f]+)
>
> see Documentation/devicetree/bindings/leds/leds-pwm.yaml
That I do care. The schematics refer to the leds by name. There is no
number assigned, much less hex. Making one up makes no sense.
User should be able to quickly (and easily) link what they see in the
schematics with DT.
So I'd prefer to submit a change for the regex rather than changing this
>
>> + };
>> +
>> + leds-gpio {
>> + compatible = "gpio-leds";
>> +
>> + led-orange {
>> + color = <LED_COLOR_ID_AMBER>;
>> + function = LED_FUNCTION_STANDBY;
>> + gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
>> + };
>
> Ditto, but you can simply use "led" since it's the only one.
>
> See Documentation/devicetree/bindings/leds/leds-gpio.yaml
>
> Neil
>
>
> <snip>
More information about the linux-amlogic
mailing list