[PATCH v9 08/12] clk: meson: g12a: make VCLK2 and ENCL clock path configurable by CCF
Neil Armstrong
neil.armstrong at linaro.org
Fri Nov 24 07:15:55 PST 2023
On 24/11/2023 15:12, Jerome Brunet wrote:
>
> On Fri 24 Nov 2023 at 09:41, Neil Armstrong <neil.armstrong at linaro.org> wrote:
>
>> In order to setup the DSI clock, let's make the unused VCLK2 clock path
>> configuration via CCF.
>>
>> The nocache option is removed from following clocks:
>> - vclk2_sel
>> - vclk2_input
>> - vclk2_div
>> - vclk2
>> - vclk_div1
>> - vclk2_div2_en
>> - vclk2_div4_en
>> - vclk2_div6_en
>> - vclk2_div12_en
>> - vclk2_div2
>> - vclk2_div4
>> - vclk2_div6
>> - vclk2_div12
>> - cts_encl_sel
>>
>> vclk2 and vclk2_div uses the newly introduced vclk regmap driver
>> to handle the enable and reset bits.
>>
>> In order to set a rate on cts_encl via the vclk2 clock path,
>> the NO_REPARENT flag is set on cts_encl_sel & vclk2_sel in order
>> to keep CCF from selection a parent.
>> The parents of cts_encl_sel & vclk2_sel are expected to be defined
>> in DT.
>>
>> The following clock scheme is to be used for DSI:
>>
>> xtal
>> \_ gp0_pll_dco
>> \_ gp0_pll
>> |- vclk2_sel
>> | \_ vclk2_input
>> | \_ vclk2_div
>> | \_ vclk2
>> | \_ vclk2_div1
>> | \_ cts_encl_sel
>> | \_ cts_encl -> to VPU LCD Encoder
>> |- mipi_dsi_pxclk_sel
>> \_ mipi_dsi_pxclk_div
>> \_ mipi_dsi_pxclk -> to DSI controller
>>
>> The mipi_dsi_pxclk_div is set as RO in order to use the same GP0
>> for mipi_dsi_pxclk and vclk2_input.
>
> Could you explain a bit more this part of about the RO ops ?
> Maybe I'm missing something.
>
> You would be relying on the reset being always the way it. It is
> probable but not safe.
>
> A way to deal with the shared GP0 would be to:
> * cut rate propagation at mipi_dsi_pxclk_sel (already done) and
> (vclk2_sel - TBD) ...
> * Set GP0 base rate through assigned-clock-rate (which you already in
> patch 11)
>
> With this, I'm not sure anything needs to be RO for the rates to be set
> properly for each subtree.
>
> Also, with the subtree above and your example in patch 11, it looks odd that
> PXCLK is manually set through DT while ENCL is not. Both are input of
> dsi driver.
So the deal is about dynamic setup of clocks for DSI bridges, not really
for panels where we can probably know in advance the clock setup.
In this particular case, we need to keep a ratio between the vclk and the
DSI bitclk, the DSI bitclk is taken from mipi_dsi_pxclk and vclk is derived
from gp0 via vclk2.
If we set the bitclk rate via mipi_dsi_pxclk, CCF will try to use mipi_dsi_pxclk_div
to achieve the rate, and it does it everytime I tried, breaking the vclk/bitclk ratio,
and we have no way to know the gp0 rate in this case.
I suspect mipi_dsi_pxclk_div was added to achieve fractional vclk/bitclk ratios,
since it doesn't exist on AXG. Not sure we would ever need it... and none
of the other upstream DSI drivers supports such setups.
The main reasons I set only mipi_dsi_pxclk in DT is because :
1) the DSI controller requires a bitclk to respond, pclk is not enough
2) GP0 is disabled with an invalid config at cold boot, thus we cannot
rely on a default/safe rate on an initial prepare_enable().
This permits setting initial valid state for the DSI controller, while
the actual bitclk and vclk are calculated dynamically with panel/bridge
runtime parameters.
For the record, the samsung-dsim used fixed rate set from DT, and they moved
from that in order to support more panel and bridges.
But they're quite lucky because usually the DSI PLL is included in the PHY,
this makes the Amlogic design quite unusual (like most multimedia stuf...).
Neil
>
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong at linaro.org>
>> ---
>> drivers/clk/meson/g12a.c | 68 +++++++++++++++++++++++++++++++++---------------
>> 1 file changed, 47 insertions(+), 21 deletions(-)
>>
>> diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
>> index cadd824336ad..fb3d9196a1fd 100644
>> --- a/drivers/clk/meson/g12a.c
>> +++ b/drivers/clk/meson/g12a.c
>> @@ -22,6 +22,7 @@
>> #include "clk-regmap.h"
>> #include "clk-cpu-dyndiv.h"
>> #include "vid-pll-div.h"
>> +#include "vclk.h"
>> #include "meson-eeclk.h"
>> #include "g12a.h"
>>
>> @@ -3165,7 +3166,7 @@ static struct clk_regmap g12a_vclk2_sel = {
>> .ops = &clk_regmap_mux_ops,
>> .parent_hws = g12a_vclk_parent_hws,
>> .num_parents = ARRAY_SIZE(g12a_vclk_parent_hws),
>> - .flags = CLK_SET_RATE_NO_REPARENT | CLK_GET_RATE_NOCACHE,
>> + .flags = CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
>
> No sure CLK_SET_RATE_PARENT is wise here.
> What you manually set in DT for the GP0, is likely to change because of
> this, isn't it ?
>
>> },
>> };
>>
>> @@ -3193,7 +3194,7 @@ static struct clk_regmap g12a_vclk2_input = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2_sel.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3215,19 +3216,32 @@ static struct clk_regmap g12a_vclk_div = {
>> };
>>
>> static struct clk_regmap g12a_vclk2_div = {
>> - .data = &(struct clk_regmap_div_data){
>> - .offset = HHI_VIID_CLK_DIV,
>> - .shift = 0,
>> - .width = 8,
>> + .data = &(struct clk_regmap_vclk_div_data){
>> + .div = {
>> + .reg_off = HHI_VIID_CLK_DIV,
>> + .shift = 0,
>> + .width = 8,
>> + },
>> + .enable = {
>> + .reg_off = HHI_VIID_CLK_DIV,
>> + .shift = 16,
>> + .width = 1,
>> + },
>> + .reset = {
>> + .reg_off = HHI_VIID_CLK_DIV,
>> + .shift = 17,
>> + .width = 1,
>> + },
>> + .flags = CLK_DIVIDER_ROUND_CLOSEST,
>> },
>> .hw.init = &(struct clk_init_data){
>> .name = "vclk2_div",
>> - .ops = &clk_regmap_divider_ops,
>> + .ops = &clk_regmap_vclk_div_ops,
>> .parent_hws = (const struct clk_hw *[]) {
>> &g12a_vclk2_input.hw
>> },
>> .num_parents = 1,
>> - .flags = CLK_GET_RATE_NOCACHE,
>> + .flags = CLK_SET_RATE_PARENT | CLK_SET_RATE_GATE,
>> },
>> };
>>
>> @@ -3246,16 +3260,24 @@ static struct clk_regmap g12a_vclk = {
>> };
>>
>> static struct clk_regmap g12a_vclk2 = {
>> - .data = &(struct clk_regmap_gate_data){
>> - .offset = HHI_VIID_CLK_CNTL,
>> - .bit_idx = 19,
>> + .data = &(struct clk_regmap_vclk_data){
>> + .enable = {
>> + .reg_off = HHI_VIID_CLK_CNTL,
>> + .shift = 19,
>> + .width = 1,
>> + },
>> + .reset = {
>> + .reg_off = HHI_VIID_CLK_CNTL,
>> + .shift = 15,
>> + .width = 1,
>> + },
>> },
>> .hw.init = &(struct clk_init_data) {
>> .name = "vclk2",
>> - .ops = &clk_regmap_gate_ops,
>> + .ops = &clk_regmap_vclk_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2_div.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT | CLK_SET_RATE_GATE,
>> },
>> };
>>
>> @@ -3339,7 +3361,7 @@ static struct clk_regmap g12a_vclk2_div1 = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3353,7 +3375,7 @@ static struct clk_regmap g12a_vclk2_div2_en = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3367,7 +3389,7 @@ static struct clk_regmap g12a_vclk2_div4_en = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3381,7 +3403,7 @@ static struct clk_regmap g12a_vclk2_div6_en = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3395,7 +3417,7 @@ static struct clk_regmap g12a_vclk2_div12_en = {
>> .ops = &clk_regmap_gate_ops,
>> .parent_hws = (const struct clk_hw *[]) { &g12a_vclk2.hw },
>> .num_parents = 1,
>> - .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3461,6 +3483,7 @@ static struct clk_fixed_factor g12a_vclk2_div2 = {
>> &g12a_vclk2_div2_en.hw
>> },
>> .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3474,6 +3497,7 @@ static struct clk_fixed_factor g12a_vclk2_div4 = {
>> &g12a_vclk2_div4_en.hw
>> },
>> .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3487,6 +3511,7 @@ static struct clk_fixed_factor g12a_vclk2_div6 = {
>> &g12a_vclk2_div6_en.hw
>> },
>> .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3500,6 +3525,7 @@ static struct clk_fixed_factor g12a_vclk2_div12 = {
>> &g12a_vclk2_div12_en.hw
>> },
>> .num_parents = 1,
>> + .flags = CLK_SET_RATE_PARENT,
>> },
>> };
>>
>> @@ -3561,7 +3587,7 @@ static struct clk_regmap g12a_cts_encl_sel = {
>> .ops = &clk_regmap_mux_ops,
>> .parent_hws = g12a_cts_parent_hws,
>> .num_parents = ARRAY_SIZE(g12a_cts_parent_hws),
>> - .flags = CLK_SET_RATE_NO_REPARENT | CLK_GET_RATE_NOCACHE,
>> + .flags = CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
>> },
>> };
>>
>> @@ -3717,7 +3743,7 @@ static struct clk_regmap g12a_mipi_dsi_pxclk_sel = {
>> .ops = &clk_regmap_mux_ops,
>> .parent_hws = g12a_mipi_dsi_pxclk_parent_hws,
>> .num_parents = ARRAY_SIZE(g12a_mipi_dsi_pxclk_parent_hws),
>> - .flags = CLK_SET_RATE_NO_REPARENT,
>> + .flags = CLK_SET_RATE_PARENT | CLK_SET_RATE_NO_REPARENT,
>> },
>> };
>>
>> @@ -3729,7 +3755,7 @@ static struct clk_regmap g12a_mipi_dsi_pxclk_div = {
>> },
>> .hw.init = &(struct clk_init_data){
>> .name = "mipi_dsi_pxclk_div",
>> - .ops = &clk_regmap_divider_ops,
>> + .ops = &clk_regmap_divider_ro_ops,
>> .parent_hws = (const struct clk_hw *[]) {
>> &g12a_mipi_dsi_pxclk_sel.hw
>> },
>
More information about the linux-amlogic
mailing list