[PATCH v1 3/3] ARM: dts: meson8m2: mxiii-plus: Enable Bluetooth and WiFi support

[neil.armstrong at linaro.org]

On 21/03/2023 18:12, Martin Blumenstingl wrote:
> The MXIII Plus uses an Ampak AP6330 Bluetooth and WiFi combo chip.
> Bluetooth is connected to &uart_A and requires toggling GPIOX_20.
> WiFi can be routed to either &sdhc or &sdio. Route WiFi to &sdhc
> since  &sdio is already connected to the SD card. Additionally WiFi
> requires toggling GPIOX_11 and GPIOAO_6 as well as enabling the 32kHz
> clock signal.
> 
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> ---
>   arch/arm/boot/dts/meson8m2-mxiii-plus.dts | 48 ++++++++++++++++++++++-
>   1 file changed, 47 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
> index fa6d55f1cfb9..aa4d4bf70629 100644
> --- a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
> +++ b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
> @@ -19,7 +19,6 @@ aliases {
>   		ethernet0 = ðmac;
>   		i2c0 = &i2c_AO;
>   		serial0 = &uart_AO;
> -		serial1 = &uart_A;
>   		mmc0 = &sd_card_slot;
>   	};
>   
> @@ -45,12 +44,32 @@ button-function {
>   		};
>   	};
>   
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +
> +		pinctrl-0 = <&xtal_32k_out_pins>;
> +		pinctrl-names = "default";
> +
> +		reset-gpios = <&gpio GPIOX_11 GPIO_ACTIVE_LOW>,
> +			      <&gpio_ao GPIOAO_6 GPIO_ACTIVE_LOW>;
> +
> +		clocks = <&xtal_32k_out>;
> +		clock-names = "ext_clock";
> +	};
> +
>   	vcc_3v3: regulator-vcc3v3 {
>   		compatible = "regulator-fixed";
>   		regulator-name = "VCC3V3";
>   		regulator-min-microvolt = <3300000>;
>   		regulator-max-microvolt = <3300000>;
>   	};
> +
> +	xtal_32k_out: xtal-32k-out-clk {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		clock-output-names = "xtal_32k_out";
> +	};
>   };
>   
>   &cpu0 {
> @@ -192,6 +211,27 @@ &saradc {
>   	vref-supply = <&vddio_ao1v8>;
>   };
>   
> +/* SDIO wifi */
> +&sdhc {
> +	status = "okay";
> +
> +	pinctrl-0 = <&sdxc_a_pins>;
> +	pinctrl-names = "default";
> +
> +	bus-width = <4>;
> +	max-frequency = <50000000>;
> +
> +	disable-wp;
> +	non-removable;
> +	cap-mmc-highspeed;
> +	cap-sd-highspeed;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vcc_3v3>;
> +};
> +
>   &sdio {
>   	status = "okay";
>   
> @@ -222,6 +262,12 @@ &uart_A {
>   	pinctrl-0 = <&uart_a1_pins>, <&uart_a1_cts_rts_pins>;
>   	pinctrl-names = "default";
>   	uart-has-rtscts;
> +
> +	bluetooth {
> +		compatible = "brcm,bcm20702a1";
> +		shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
> +		max-speed = <2000000>;
> +	};
>   };
>   
>   &uart_AO {

Reviewed-by: Neil Armstrong <neil.armstrong at linaro.org>