[PATCH] mmc: meson-gx: increase power-up delay
Marc Gonzalez
marc.w.gonzalez at free.fr
Thu Mar 16 09:32:21 PDT 2023
On 16/03/2023 12:59, Ulf Hansson wrote:
> If the problem is regulator specific, this would be the correct thing to do.
>
> Although, if the problem is pwrseq specific, like that we need a delay
> after enabling the clock and asserting the GPIO enable pin for the
> WiFi chip, then we have the "post-power-on-delay-ms" of the pwrseq
> node to play with instead.
Heiner, Jerome, Uffe, Amlogic DT maintainers,
Perhaps tweaking the driver for every user is too intrusive.
Another solution would be to factorize all boards that implement
the reference design SDIO-based RF (WiFi + BT using brcm).
Then we can add post-power-on-delay-ms = 20 in sdio_pwrseq.
NB: there's vddio_ao1v8 vs vddao_1v8 in sei510.
Is my addition OK?
RFC prototype:
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-radxa-zero.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-radxa-zero.dts
index e3bb6df42ff3e..42b5dcf358912 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-radxa-zero.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-radxa-zero.dts
@@ -6,6 +6,7 @@
/dts-v1/;
#include "meson-g12a.dtsi"
+#include "meson-g12a-ref-design-brcm-rf.dtsi"
#include <dt-bindings/gpio/meson-g12a-gpio.h>
#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
@@ -53,13 +54,6 @@ emmc_pwrseq: emmc-pwrseq {
reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
};
- sdio_pwrseq: sdio-pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
- clocks = <&wifi32k>;
- clock-names = "ext_clock";
- };
-
ao_5v: regulator-ao_5v {
compatible = "regulator-fixed";
regulator-name = "AO_5V";
@@ -182,13 +176,6 @@ codec {
};
};
};
-
- wifi32k: wifi32k {
- compatible = "pwm-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
- };
};
&arb {
@@ -299,37 +286,6 @@ &saradc {
vref-supply = <&vddao_1v8>;
};
-/* SDIO */
-&sd_emmc_a {
- status = "okay";
- pinctrl-0 = <&sdio_pins>;
- pinctrl-1 = <&sdio_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
- #address-cells = <1>;
- #size-cells = <0>;
-
- bus-width = <4>;
- cap-sd-highspeed;
- sd-uhs-sdr50;
- max-frequency = <100000000>;
-
- non-removable;
- disable-wp;
-
- /* WiFi firmware requires power to be kept while in suspend */
- keep-power-in-suspend;
-
- mmc-pwrseq = <&sdio_pwrseq>;
-
- vmmc-supply = <&vddao_3v3>;
- vqmmc-supply = <&vddao_1v8>;
-
- brcmf: wifi at 1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
/* SD card */
&sd_emmc_b {
status = "okay";
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-ref-design-brcm-rf.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a-ref-design-brcm-rf.dtsi
new file mode 100644
index 0000000000000..e462324596964
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-ref-design-brcm-rf.dtsi
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Amlogic, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+};
+
+/* SDIO */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr50;
+ max-frequency = <100000000>;
+
+ non-removable;
+ disable-wp;
+
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddao_1v8>;
+
+ brcmf: wifi at 1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
index 23b790c6469d3..e12aeb956b7d7 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
@@ -6,6 +6,7 @@
/dts-v1/;
#include "meson-g12a.dtsi"
+#include "meson-g12a-ref-design-brcm-rf.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/meson-g12a-gpio.h>
@@ -96,6 +97,15 @@ emmc_1v8: regulator-emmc_1v8 {
regulator-always-on;
};
+ vddao_1v8: regulator-vddao_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
vddao_3v3: regulator-vddao_3v3 {
compatible = "regulator-fixed";
regulator-name = "VDDAO_3V3";
@@ -143,20 +153,6 @@ vddio_ao1v8: regulator-vddio_ao1v8 {
regulator-always-on;
};
- sdio_pwrseq: sdio-pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
- clocks = <&wifi32k>;
- clock-names = "ext_clock";
- };
-
- wifi32k: wifi32k {
- compatible = "pwm-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
- };
-
sound {
compatible = "amlogic,axg-sound-card";
model = "SEI510";
@@ -375,37 +371,6 @@ &saradc {
vref-supply = <&vddio_ao1v8>;
};
-/* SDIO */
-&sd_emmc_a {
- status = "okay";
- pinctrl-0 = <&sdio_pins>;
- pinctrl-1 = <&sdio_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
- #address-cells = <1>;
- #size-cells = <0>;
-
- bus-width = <4>;
- cap-sd-highspeed;
- sd-uhs-sdr50;
- max-frequency = <100000000>;
-
- non-removable;
- disable-wp;
-
- /* WiFi firmware requires power to be kept while in suspend */
- keep-power-in-suspend;
-
- mmc-pwrseq = <&sdio_pwrseq>;
-
- vmmc-supply = <&vddao_3v3>;
- vqmmc-supply = <&vddio_ao1v8>;
-
- brcmf: wifi at 1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
/* SD card */
&sd_emmc_b {
status = "okay";
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
index b2bb94981838f..68a8876386115 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
@@ -6,6 +6,7 @@
/dts-v1/;
#include "meson-g12a.dtsi"
+#include "meson-g12a-ref-design-brcm-rf.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/gpio/meson-g12a-gpio.h>
#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
@@ -60,13 +61,6 @@ emmc_pwrseq: emmc-pwrseq {
reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
};
- sdio_pwrseq: sdio-pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
- clocks = <&wifi32k>;
- clock-names = "ext_clock";
- };
-
flash_1v8: regulator-flash_1v8 {
compatible = "regulator-fixed";
regulator-name = "FLASH_1V8";
@@ -226,13 +220,6 @@ codec {
};
};
};
-
- wifi32k: wifi32k {
- compatible = "pwm-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
- };
};
&arb {
@@ -391,37 +378,6 @@ &usb {
dr_mode = "host";
};
-/* SDIO */
-&sd_emmc_a {
- status = "okay";
- pinctrl-0 = <&sdio_pins>;
- pinctrl-1 = <&sdio_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
- #address-cells = <1>;
- #size-cells = <0>;
-
- bus-width = <4>;
- cap-sd-highspeed;
- sd-uhs-sdr50;
- max-frequency = <100000000>;
-
- non-removable;
- disable-wp;
-
- /* WiFi firmware requires power to be kept while in suspend */
- keep-power-in-suspend;
-
- mmc-pwrseq = <&sdio_pwrseq>;
-
- vmmc-supply = <&vddao_3v3>;
- vqmmc-supply = <&vddao_1v8>;
-
- brcmf: wifi at 1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
/* SD card */
&sd_emmc_b {
status = "okay";
More information about the linux-amlogic
mailing list