[PATCH v1 5/6] arm64: dts: meson: a1: introduce UART_AO mux definitions
Dmitry Rokosov
ddrokosov at sberdevices.ru
Wed Jun 28 07:51:10 PDT 2023
Neil, Martin,
On Mon, Jun 26, 2023 at 03:34:38PM +0200, neil.armstrong at linaro.org wrote:
> Hi,
>
> On 25/06/2023 23:07, Martin Blumenstingl wrote:
> > On Wed, Jun 7, 2023 at 10:16 PM Dmitry Rokosov <ddrokosov at sberdevices.ru> wrote:
> > >
> > > From: Oleg Lyovin <ovlevin at sberdevices.ru>
> > >
> > > The Amlogic A1 has a UART_AO port, which can be used, for example, for
> > > BT HCI H4 connection.
> > >
> > > This patch adds mux definitions for it.
> > In the past we've only taken the pinctrl definitions if we have a
> > board that uses them.
> > Neil, do we still have the same policy in place? If so this patch
> > should be sent with the series that adds support for your A1 board.
>
> Yes and no, if the work is done I'll take it, but yeah since upstream linux
> hates dead code, let's only define what's necessary.
>
I'll prepare the patches for ad401 reference board, and share the in the
next patch series version.
> >
> > > Signed-off-by: Oleg Lyovin <ovlevin at sberdevices.ru>
> > > Signed-off-by: Dmitry Rokosov <ddrokosov at sberdevices.ru>
> > > ---
> > > arch/arm64/boot/dts/amlogic/meson-a1.dtsi | 16 ++++++++++++++++
> > > 1 file changed, 16 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> > > index 0efd922ca7e1..3eb6aa9c00e0 100644
> > > --- a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> > > +++ b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> > > @@ -118,6 +118,22 @@ gpio: bank at 400 {
> > > gpio-ranges = <&periphs_pinctrl 0 0 62>;
> > > };
> > >
> > > + uart_a_pins: uart_a {
> > Only our newer .dtsi (e.g. meson-g12-common.dtsi) are following the
> > pattern where node names should use dashes instead of underscores.
> > So please use: uart_a_pins: uart-a { ...
>
> The new scheme which should be use should be:
>
> uart_a_pins: uart-a-pins-state {
>
> but it wasn't enforced in the pinctrl yaml pushed by heiner, but for sure
> no underscores in the node name.
>
Okay, got it
> >
> > [...]
> > > + uart_a_cts_rts_pins: uart_a_cts_rts {
> > similar to the comment from above:
> > uart_a_cts_rts_pins: uart-a-cts-rts { ...
> >
> > > + mux {
> > > + groups = "uart_a_cts",
> > > + "uart_a_rts";
> > > + function = "uart_a";
> > > + bias-pull-down;
> > Out of curiosity: is this pull down needed on all boards or just specific ones?
> > It seems like all other SoCs use bias-disable for the RTS/CTS pins.
> >
> >
> > Best regards,
> > Martin
>
--
Thank you,
Dmitry
More information about the linux-amlogic
mailing list