[PATCH 2/2] arm64: dts: add support for T7 based Amlogic AN400

Krzysztof Kozlowski krzysztof.kozlowski at linaro.org
Mon Jun 26 08:41:05 PDT 2023


On 26/06/2023 11:52, Xianwei Zhao wrote:
> Amlogic T7 is an advanced application processor designed for smart display.
> 
> Add basic support for the T7 based Amlogic AN400 board, which describes
> the following components: CPU, GIC, IRQ, Timer, UART. It's capable of
> booting up into the serial console.

Few nits.

...

> +				core3 {
> +					cpu = <&cpu7>;
> +				};
> +			};
> +		};
> +
> +		cpu0:cpu at 0 {

You miss spaces after labels.

> +			device_type = "cpu";
> +			compatible = "arm,cortex-a73";
> +			reg = <0x0 0x0>;
> +			enable-method = "psci";
> +		};
> +
> +		cpu1:cpu at 1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a73";
> +			reg = <0x0 0x1>;
> +			enable-method = "psci";
> +		};
> +
> +		cpu2:cpu at 2 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a73";
> +			reg = <0x0 0x2>;
> +			enable-method = "psci";
> +		};
> +
> +		cpu3:cpu at 3 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a73";
> +			reg = <0x0 0x3>;
> +			enable-method = "psci";
> +		};
> +
> +		cpu4:cpu at 100 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x0 0x100>;
> +			enable-method = "psci";
> +		};
> +
> +		cpu5:cpu at 101{
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x0 0x101>;
> +			enable-method = "psci";
> +		};
> +
> +		cpu6:cpu at 102 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x0 0x102>;
> +			enable-method = "psci";
> +		};
> +
> +		cpu7:cpu at 103 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x0 0x103>;
> +			enable-method = "psci";
> +		};
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-0.2";
> +		method = "smc";
> +	};
> +
> +	xtal: xtal-clk {
> +		compatible = "fixed-clock";
> +		clock-frequency = <24000000>;
> +		clock-output-names = "xtal";
> +		#clock-cells = <0>;
> +	};
> +
> +	soc {
> +		compatible = "simple-bus";
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		gic: interrupt-controller at fff01000 {
> +			compatible = "arm,gic-400";
> +			#interrupt-cells = <3>;
> +			#address-cells = <0>;
> +			interrupt-controller;
> +			reg = <0x0 0xfff01000 0 0x1000>,
> +			    <0x0 0xfff02000 0 0x0100>;
> +			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
> +		     };

Fix indentation.

> +
> +		apb4: bus at fe000000 {
> +			compatible = "simple-bus";
> +			reg = <0x0 0xfe000000 0x0 0x480000>;
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
> +
> +			uart_a: serial at 78000 {
> +				compatible = "amlogic,meson-s4-uart",
> +					     "amlogic,meson-ao-uart";
> +				reg = <0x0 0x78000 0x0 0x18>;
> +				interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
> +				status = "disabled";

Please, don't put status in the middle of properties...



Best regards,
Krzysztof




More information about the linux-amlogic mailing list